Linksys Wireless Router :: E4200 Not Recognizing Hard Drive (Seagate 7200)?
Jul 2, 2012
I have a E4200 router, and I had previously plugged in a small external hard drive just to test the functionality. The router seemed to recognize the storage, and the computers on the network could see it as a shared drive. Now I have plugged in a Seagate 7200 internal hard drive inside a Rocketfish enclosure, but the router is not recognizing anything. I just upgraded the firmware to 1.0.04, but there was no change. Are there problems using an enclosure rather than just plugging in an external hard drive?
View 1 Replies
ADVERTISEMENT
Sep 17, 2012
When i connect my Seagate Backup Plus Drive to the USB port on my EA3500 the drive becomes available on my network but it never spins down even when not in use. Is there any way to correct this? If the drive spins 24/7 its going to die very fast.
View 2 Replies
View Related
Apr 15, 2012
i have a seagate goflex home wireless hardrive and kaspersky PURE, and the only way i can get the hard drive to work is by turning off kasperky's firewall. is there anyway i can add an exception on the firewall so i can have it running and still have my wireless hard drive running at the same time
View 1 Replies
View Related
Sep 6, 2011
I just updated to the new firmware 1.0.02 and the USB stop working for my External Hard WD 500GB harddrive. I had to roll back to firmware 1.0.01 for it work
View 2 Replies
View Related
Jun 20, 2011
Yesterday i upgraded my e4200 to firmware version 1.0.02 (Build 13) after waiting since february.Unfortunately it still doesn't recognize my WD 500 GB Essentials.
View 9 Replies
View Related
Nov 4, 2011
I have an E4200 with a 500GB WD hard drive attached to the USB port. I also have 3 computers on the network named "THINK", "PC", and "DELL". THINK is mixed Wired and Wireless - depending on what I'm doing - Win7 Professional, DELL is plugged into a Range Extender. (RE1000) - WinXP (This one isn't as important: It's an older machine) PC is always hardwired. - Win7 Ultimate, Recently, THINK has unable to see DELL, OR even the HD connected to the router, but it can see PC. It can also see the HD as a media device - just not as a computer or device I can browse as it does on PC.However, PC can see everything: THINK, DELL, AND the HD and can access them all the way I would like it to be. Also - MY PS3 DOES see the Media Share and can access it. Edit: Also just discovered both internal and external FTP no long works. Why can't THINK see the HD connected to the router regardless if I'm wired or wireless? As far as I can tell, all the settings are identical on both THINK and PC. Is there a router setting I'm missing? IPV6 is disabled and I've treid the basic disabling of HOMEGROUP and anything that goes with it - but nothing yet.
View 9 Replies
View Related
Aug 11, 2011
I just purchased a Linksys e4200 router today along with a WD 2TB MyBook hard drive. My intent is to set these two up together so that i can share files on the hard drive with: Computers on my home network ( 1 Windows 7 desktop wired, 1 windows 7 laptop wifi, 1 XP netbook wifi)Computers remotely over the internetSmartphones (Android and Apple) on my home networkSmartphones (Android and Apple) remotely over the internet. My questions are: Set-up remote access for fileshare with smartphones?What is the easiest way to set-up and configure this?
View 9 Replies
View Related
Jan 20, 2012
I have realized that E4200 V1 I have, with 1.03 firmware, seems to be dying when I reboot it and it tries to load the USB HD I have connected to it. By die I mean the web server does not work anymore (http://192.168.1.1), and new computers can't connect to the router. I suspect it is due to the amount of files I have in the External Disk Drive -I used to have Media Server enabled, but I disabled it because this problem was happening, and I only left File Server enabled. Now since I moved many of my pictures to it, it seems even File Server is causing problems, and if neither one work for me, then this router does not justify its money, since that was the only reason I bought this E4200 hardware. These problems are solved in V2? Since it is still under warranty, I could try to exchange my V1 for a V2 version.
View 3 Replies
View Related
Oct 13, 2011
I just bought an E4200 hoping to plug my external hard drive in. Unfortunately, the drive isn't even showing up as connected. I'm using an Icy Box enclosure around a toshiba laptop drive right now.
View 4 Replies
View Related
Jan 5, 2012
My E4200 works beautifully, and was working fine with the Toshiba 500 GB portable drive that I had on it for a week or so. I tried to plug in my WD MyBook Essential (Passed on the list of compatible drives), but the router is not detecting it. Further, when the drive is plugged in, the router stops receiving new wireless connections. Even if I reboot a laptop that was previously connected, it says that that the passkey is incorrect. When the drive is plugged in, I can't even log in to the 192.168.1.1 - it's as if the router creates a firewall around it and refuses every new connection on every port.
View 1 Replies
View Related
Mar 20, 2011
I just bought a Linksys E4200 from bestbuy tonight, mostly for the feature of plugging my hard drive into it to use it as a media server, and being able to read & write to it from any computer on my network. I have searched for hours on end trying to fix my problem. I login to my router (at 192.168.1.1), I go to the storage tab, I then click the "Create Share" button next to my WD hard drive in the list and nothing happens. Ive tried this on four different computers, and three different browsers now to no avail.
Some random information:
Computer: Dell XPS 420
Router: Linksys E4200
Hard Drive: WD 1TB
View 9 Replies
View Related
Oct 15, 2011
I just updated Cisco software and my external hard drive is no longer recognized by Cisco. It is a Seagate drive that is listed on the Cisco tested - passed - approved list. It worked prior to this update. I have disconnected the drive. Reconnected it. Rebooted. Turned machine and router on and off and its still not recognized.
Model name: Linksys E4200
Model number: E4200
Firmware version: 1.0.03 build 14
Operating system: Windows 7 SP 1
Software version: 1.4.11266.0
Connection type (WAN): DHCP
View 7 Replies
View Related
Jan 26, 2012
I had an Iomega 1TB External Hard Drive connected to my E4200 router. I had shares confgured and they were properly running on the network.
As of yesterday, this all stopped working. The router does not see the drive; it is as though it is not plugged in.
I rebooted the router and it still does not work. I've connected the hard drive directly to my PC to verify that it works there, and it does. The router is running Ver.1.0.03 (Build 14) of firmware (the latest).
View 9 Replies
View Related
Jan 14, 2012
If I were to take a e4200v2 and use it as an access point (disable DHCP), would the USB port connected to a Hard Drive still function as network storage?
View 5 Replies
View Related
Dec 3, 2011
Is there any way to connect a Seagate USB drive to the E4200.i have 2 USB portables and 1 USB with power cable, none of them seem to be recognized by the router
View 9 Replies
View Related
Jun 25, 2012
Bought GoFlex Home 3TB, plugged into Cisco WRT310N V2, w/ Desktop PC (Win 7 64bit) does not recognize the drive. Get NETWORK ERROR "Windows cannot access \goflex_home" Error Code: 0x80070035. Can not map netork drive. Under Win Explorer the drive DOES appear as "GoFlex Home:UPNP-AV" in TWO places, 1) under Media Devices & 2) Under Storage. Bother places are treated as MEDIA because, when I click on either of them it opens Windows Media Player! I can type in the IP address in BOTH IE & WIn Explorer and it will take me to the web page for the drive, where i can log in and create users, add folderes, etc. I WANT TO USE THIS AS A BACK-UP DRIVE, but can't get WINDOWS TO RECOGNIZE IT. I have turned off McAfee
View 3 Replies
View Related
Jun 26, 2011
I attached WD My Book Mirror 2TB to E4200 with firmware 1.0.01 but it was very UNreliable. It would give I/O errors when I tried to access the harddisk. So I upgraded to firmware 1.0.02. Now E4200 doesn't recognize my hard disk at all. Yes, my hard disk is in the list of tested devices using NTFS.I contacted support but no luck.
I also have bad range with this router where I am only about 20ft from the router (2 walls in between) but I get about 3 bars out of 5 on my Windows 7. Could it be because I purchased a refurbished product directly from Cisco?
View 2 Replies
View Related
Jul 10, 2010
I have my router setup fine to the internet, as well as the media server. I can't figure out how to access the hard drive from my laptop, however. The manual says put 192.168.1.1 in the address field of windows explorer, but it just gives me the "Setup" page for the router.
View 9 Replies
View Related
Jul 31, 2012
I recently copied files to my hard drive that was connected directly to my computer (via USB).When I connected the disk back to E3000 the files were missing. I connected it back to PC directly and verified the files are there.My PC runs Windows 7 Enterprise.Why can't I see files copied via local connection when I connect the disk to E3000.I carefully compared the permissions with files that I can see just fine and there is no difference - same permissions, same owner.I also get all kinds of permission errors when I try to delete a files from the network drive.
View 9 Replies
View Related
Sep 18, 2011
I had previously posted about problems with the E1550 not being able to recognize NTFS formated hard drives. After multiple retries and reformats I was finally able to get it to work and was able to backup my system files to that NTFS hard drive.
Now, little more than a week later I setup to run my backup to run again and once again the E1550 is not accessing the hard drive. The same one it had previously acknowledged and allowed me to save to.
The E1550 sees that there is a hard drive out there but all it says is "Detecting..." this does not change.
I need this to be fixed and stay fixed. If it is going to do this every time I turn on the drive to do weekly backups, then I need to get a different wireless router.
View 5 Replies
View Related
Jun 4, 2012
Can I use a USB hub to connect more than 1 hard drive/flash drive device to the EA4500?
View 3 Replies
View Related
Jan 7, 2013
EA 4500 seems to work fine. Have a Seagate 3 TB HD connecfed to USB. Have LG Smart box connected to EA4500 by Cat5e cable. HD hard drive contents shows and accesses ok on PC via wireless. Smart box showed HD but only media files in "documents" directory, did not show "TV" & "Movies" directories.
Reset Router Media Server Access with "TV" & "Movies" directories - presto LG smarbow showed directories now and worked fine. This morning will no longer show "TV" & "Movies" directories on Smart box. Have tried deleting and resetting Router Media Server Access with "TV" & "Movies" directories several times, no luck.
View 1 Replies
View Related
Jun 23, 2012
WD essential 2GB hard drive connects OK through cisco connect but when I click on the shortcut or try to access the drive I get access denied duer to permission to the ip address
View 4 Replies
View Related
Jan 1, 2011
I just installed this router and connected the hard drive (Western Digital 1TB) which worked fine at first. When I moved some movie files to another folder they lost all of their data. The file names are still present, but all the media files show zero bytes and are no longer usable. Is there anyway to get these files back? I have been digitizing all our movies to the tune of about 90GB. What could be going on here? I disconnected the HD from the router and plugged directly into the laptop. Still shows the file names, but each file is still at zero bytes. Not a cool way to have a media server for your house!
View 6 Replies
View Related
Sep 2, 2012
I have mapped the attached hard drive to my EA4500 on my PC and can access folders and files on my LAN PC. However, when I come in through the Internet via an iOS device, I can see folders but when I try to enter the folder, all I get is a message that displays "|Folder|Enter Into Folder|Select|. There is no click-through capability other than "Return to Upper Folder", which takes me back to folders.
View 8 Replies
View Related
Mar 21, 2012
do external hard disks automatically spin down after a period with no access/use when connected with the USB port of the WRT160NL?
View 1 Replies
View Related
Jul 22, 2012
I bought a seagate USB hard drive today from Target. Its a 2TB and I was going to use it via USB attached to my router. I connected it and the Linksys firmware detected it and I was able to create the appropriate folders on the drive for storage through the linksys GUI.My issue is that I am now trying to move my movies and tv shows over to the drive and it isn't allowing me to do that.
I get an error message that says "You don't have access to //myshare. contact your administrator".
I'm not sure why I was able to create folders on this drive but am unable to move files to it. Makes no sense to me. Write permission is write permission no?My machine which currently stores the media files is windows7 utimate. The router is E3000 using up to date stock firmware.
View 1 Replies
View Related
Mar 6, 2013
I bought an EA 3500 refurbished through linksys. I can't configurate it using the CD-Rom. Always said "can't find your router". So I flash with the classic firmware, and it fixs the problem and automatically upgrade to smart Wi-Fi. That being said, whenever I plug in a portable hard drive, the router disconnect from internet after a minute. I tried my seagate HDD and also my flash driver. Both Lost internet after a minute or so. So I think it is probably the router's problem.
View 4 Replies
View Related
Aug 16, 2012
I was wondering if the EA3500 would support splitting the USB (buying a USB tree) to allow for both a printer and hard drive to connect at the same time?
View 1 Replies
View Related
Aug 3, 2011
Im looking to swap out my older 3.5" drive in an external enclosure for a Seagate - FreeAgent GoFlex Desk 2TB. Can I just drag and drop the 200+gb of files on my current drive to the new Seagate - FreeAgent GoFlex Desk 2TB? Or do I need to re configure the new drive in my web browser.
E4200 media server in .02 firmware
View 9 Replies
View Related
Mar 17, 2013
I have an e4200 with the latest firmware 2.1.39. I just upgraded the firmware due to connection issues with my DSL. I now have the same issues with disconnects but I believe they are being caused by a different issue. When I try and log into my router through the IP address it wont let me, it says it can't find the router. Eventually after getting in the first time by using the default password, I have twice found out that all my settings are gone. This has happened twice this week and only happened after upgrading the firmware but I can not tell if firmware is causing it or if it is hardware related. I now reboot and restore saved firmware but that is a hassle and am pretty sure that is not the way it was designed to work.
View 9 Replies
View Related
Feb 8, 2012
I am a avid fan of Linksys routers i blindly go buy it. But one feature which i feel isn't there on linksys is the ability to start downloads on the router and also peer to peer capability such as torrents. Asus routers have this and it works flawlessly love to have this feature on the Linksys routers. This is one and only request i ask for in firmware update?
View 1 Replies
View Related
May 10, 2012
I just bought an IOSafe Solo G3 3TB drive. My E4200 does not seem to mount the drive correctly when formatted as GPT. When I re-format as MBR, it mounts with no problem, but this limits the drive size to 2TB. Has anyone had success with this HD or others using GPT format?
View 9 Replies
View Related
