Cisco Routers :: How Does Quality And Longevity Of SRP500 Series Compare To RV Series
May 27, 2012
My Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
I've buy a SRP500 Series Router (ADSL 2+).My ISP need RFC1483 Routed with LCC encapsulation type but this router dont have this type of encapsulation available in WAN settings. What can i do to use this device with my ISP adsl connection ?
I'm using a SRP521W-U. I've set up a SIP account on Line 1. I would like to be able to answer incoming calls on both FXS1 and FXS2. How do I achieve that both ports will ring?
why I can't use cisco ehwic-3g-hspa-u card in cisco 2800 series and 1841 series router?documentation said that it should work with that devices but when I installed it, it doesn't work even as device i can't see I am using cisco latest ios advance ent. 15.1(4)M4?
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
I have not done much with business routers, but we have a 1700 series with a WAN WIC-1ENET card with a RJ45 connection. We had a T1 line and will be moving to ehternet. We are going to be moving to a 20MB line, and i just wanted to make sure I have the right connections before installing. We also have a T1 line in another loaton and would be moving to this same 2811 router there as well.We would also like to copy over the configuration from 1700 series router to the 2811 router. Would it be easier to do it by hyper-terminal? Also if we keep the 1700 routers are they capable of using layer-3?
I'm just courious as to the platform specs of the SRP500 series routers. What processor is used, how fast is it and how much RAM and flash do they have?
Does the two listed POE switch ports on the 880 series routers are active out of the box (default) or is configuration or extra parts required as internet pictures appear to show what looks like a power connector new to the POE ports?
The first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
I have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
I'm considering upgrading a small business to the newly released RV180 or RV180W.Does the RV180 series support 6rd (IPv6 rapid deployment?).I see 6rd documented in the other small business routers (e.g. RV110), but I can't find it in the RV180 documentation.
I have been able to put two Linksys routers in series no problem but this doesn't seem to work with an RV042.I have a number of customers that need to connect to a private email network via a router based VPN, but since VPN traffic is not filtered in the firewall, I would like to use an older Linksys router to manage the VPN(s) and have it pass data in through the filters of an RV042 on the DMZ port.I am getting stuck on the very frist part of this. Although I can connect to both the RV042 and LinkSys directly (by adjusting my subnet), I cannot ping the Linksys when it is connected through the DMZ port even if I disable the RV042 Internet port.
I know both the Internet and DMZ ports work on the RV042. I suspected that perhaps the RV won't pass through private IPs and tried known available pubic IPs instead of the 192.168.2.x subnet, but still no ping.What would be limiting the RV in this case? Is is possible to setup the RV to work in series with another router? Is there any other way to filter VPN traffic?
i have a demroom set up which includes a sr520 as the edge router connecting to the ISP and i have a uc 560 connected to that which is working fine i also have a new business edition 3000 and a 800 series router which im looking to connect to the sr 520 for access to the ISP as the 800 series doesn't have a ADSL line on it .i have given the 800 series routers wan interface a static address of 192.168.75.14 wich is from the address range in the sr520s default vlan and excluded the address from the DHCP pool. now from the ccp express on the 800 s i can ping the wan port of the 800 s and the default vlan/gateway of the sr520 and the wan ip of the sr520 but no further also once i try pinging it from the cmd on windows i cant ping any further that the wan interface on the 800 s .
I'm looking to use 861s at few remote sites connecting to a 881 in the main office using Easy VPN. If I was to get 2 ISPs at the main office, can I configure it in a way that if the primary WAN failsover to the secondary, the VPN tunnels from remote sites will also failover?
Would you recommend an ASA 5505 at main office over the 811?
How come the 2600 series IOS has the show mac-address command but it does not display anything? you need to use show arp? is this for when you use one of those network modules that is a switch?
I've goggled and searched here, and I can't seem to find what I'm looking for. I need to make a couple changes to a clients Cisco 800 series router, enable ping replies add ip addresses to the ssh ACL.I can't seem to find any basic commands for CLI anywhere.
Normaly all incoming IP addresses can use NAT to gain access. I would like to make a rule that only one IP address can connect to my router and use that port or range of ports defined.
Is there a way to configure a SRP 527W on such a way?
If not possible now, can I expect a software update ?
which 800 series routers allow 20 Mbps throughput across the WAN port? I have a cable modem that outputs this speed but am having difficulty finding a router that will accept this throughput across the WAN port.
I wondered, how much power do the SRP520-U series actual draw? Compared to commonly used home-grade equipment I think the power consumption is above average?
We have deployed a number of 800 series routers for some of our clients and have found that in many cases they seem to disconnect at an excessive rate. When I connected to the console of one the other day I could see that the virtual-interface for the ADSL connection was down, but not the ATM or DSL interface. If I disconnected the cable and reconnected the virtual-circuit came back up momentarily before disconnecting within a minute.
If I switched off the router for a few minutes and powered it back on it would usually remain up for a few hours. I reconfigured the router again using exactly the same config and it seemed to stay up for quite long periods for 4 or 5 days before reverting to type. [code]
We have an MPLS network to a half dozen remote sites. At our main location we have a 2800 series router. In the routers config are the following lines for QOS. When I go to the routers on the other end of the MPLS, none of them are configured with these same policies. Would these not be in the running config of the 1800 series routers, or is this not setup correct and this should be removed?
I am a mac user, and whenever I try to open this following link: [URL] to log in my router, nothing happens. Firefox and/or Safari browse the link for a while, but then nothing happens. I am using a Zyxel prestige series 600.
I bought some hardware and created my own lab to prepare for the CCNA. I only have one machine with a serial port and whenever I try to connect to a router (I've tried multiple purchased from different sources) nothing happens on the screen. If I wait for a couple of seconds and hit enter I get the response shown on the screen in the screenshot I have inserted. If this image is too small I have also attached. looks like it has already asked me this but I am unable to see it. Shouldn't I see some information when I attempt to connect, some acknowledgement that I have connected? I have tried using both hyperterminal anbd PuTTy.
The products from SRP 540 series line (541w etc) will ever support IPv6 features or remote VPN (eg SSL VPN or Cisco QuickVPN)? If yes, is there a time horizon?
We are migrating from a Microwave T1 WAN to a Fiber ring WAN which I'll be connecting to our providers Ciena Metro E switches. Eventually we are going to move away from the routers, but the network is a little too complex as well as spanned across a lot of miles. Since I am the only networking personnel here, I would like to first simply migrate to the fiber by simply moving the connection configs off of the T1 interfaces, and onto one of the Gig interfaces on the 7206 and on one of the Fe interfaces on the 3900 (which is actually a 3700 series because the line card on the 3900 is toast). If this works, I will need to purchase Fe line cards for the 7206, because I found out that the virtual interfaces do not support Policy Mapping for our QOS and Multicasting.
