which 800 series routers allow 20 Mbps throughput across the WAN port? I have a cable modem that outputs this speed but am having difficulty finding a router that will accept this throughput across the WAN port.
View 21 Replieswhat is the throughput of the 1941 and 3945 series routers, i didn't find this info in the datasheet for both!
View 2 Replies View RelatedI have a 128mb connection with a sa 500 series fw/router. When I turn on the ips function my throughput drops to 15 Mbps and the CPU max goes up to 100%. What gives?
View 2 Replies View RelatedI'm using a SRP521W-U. I've set up a SIP account on Line 1. I would like to be able to answer incoming calls on both FXS1 and FXS2. How do I achieve that both ports will ring?
View 2 Replies View RelatedMy Draytek 2710 just dies after 2 years so I was looking for something a little more reliable and noticed the spec of the SRP527W-U.I take it with only one antenna and reading a couple of past discussions, the wireless will only manage n-lite as some people call it i.e. 150Mbps, and not the full 300? Oh, and are the ports still only 100M and not Gig?I know the 547 would tick both these boxes but we are talking twice the price. How does the quality and logevity of the SRP500 series compare to the RV series (which would need an adsl modem) or the Linksys boxes?
View 1 Replies View RelatedInstallation of 2 x 4 Mbps MPLS circuit on primary router (CISCO 2951) and 1 x 8 Mbps Ethernet link on secondary router (Cisco 2951). We have successfully implement the primary router with 2 x 4 Mbps MPLS circuit. Site is having two computer room CR1 and CR2 and distance between both room is 200mts. CR1 is having primary core router and primary core switch where the service provider terminated the new MPLS circuit and we have done the successful implementation. CR2 is having Secondary core router and secondary core switch where we needs to have the termination of Ethernet link but service provider has delivered the Ethernet link on the CR1 which is incorrect DMARC Location.
Both the computer rooms are connected via optical copper can we use that copper to connect the circuit on CR2, as per my understanding we can use the optical fiber to connect the wind circuit on secondary router on CR2 by using the media connector.
I just ran some speedtests om my PC on the advice of my isp to see if my Linksys WRT54G router might be bad. As a result, I found that the router might not be entirely bad, but it might not be entirely good, either. I got .77 Mbps dowload and .17 Mbps upload on the first speedtest. I got .43 Mbps download on the second speedtest and the speed test hung hear the end. When I connected an IMac to the cable modem with an ethernet cable, the IMac ran strong. So the tech thought I should get a new router.
But wait a minute, isn't there a network adapter in the PC that the router talks to? Might the adapter be the problem, not the router? So I speedtested the wireless network to the IMac. That speedtest was fine, tiptop, like the ethernet direct connection test noted above. Did that tell me that the problem is in my PC network adapter, not the router? Then, I retested (speedtested) the connection on the PC and it was fine...excellent. Good up and down speeds, no hangs.Then, I checked the PC adapter (a Belkin). I saw three adapters on Device Manager, including the Belkin. I downloaded new drivers for the adapters (except for the Microsoft Virtual WiFi Minipoty Adapter - because it got a warning that the download software wasn't signed and might harm my computer).
So I have installed my new E4200 version 1 and I am disappointed with the speeds. My computer has a wireless N card and gigabit Ethernet compatibility. I am currently getting a miserly 54 mbs wireless and 100 mbs on the wire (connected with cat6 all the way)... Anything I should try to get close to advertized speeds?
View 9 Replies View RelatedIn other words. If my cable modem only has 50 mbps is that all I will get out of my wireless router, even if the router has a higher mbps rating/
View 8 Replies View RelatedWhich is the wireless speed of this router? No speed infos are present in the official web site. In the web some sites say it's a 300, others say it's a 150, others 248...
View 9 Replies View RelatedI have a desktop and laptop here, the desktop being mine custom built wireless and all, and my buddies desktop.The issue that I'm having is that my desktop, regardless of wired or wireless gets 25 mbps down speed, and the laptop gets only 2.5 mbps down speed wired or wireless
View 4 Replies View Related300 M bps drops to 150 M bps when it recycle power. I met all requirements for 300 M bps connection this happen only in 2.4 g Hz Band width.
View 1 Replies View Relatedi have gotten a question from a partner in regards to the throughput on both LAN and WAN on the SRP541W. I can't really find that on the datasheet.
View 4 Replies View RelatedWhat is the WAN to LAN Throughput of RV042 router with QoS and SPI enable?
Will the RV042 router able to support a 60Mbps down 3Mbps up Internet connection with QoS enable and SPI enable without slowing down the connection?
according to [URL] enabling WMM should increase wireless performance. Although this article is rather old, how is the RV220W expected to behave?
In my case, speed measurements show a clear decrease in wireless performance when WMM is enabled.
For example:
WMM enabled - max 15MBits/s (ticked WMM checkbox - default settings)
WMM disabled - max 40MBits/s
When WAN traffic meter is enable on RV180 router maximum throughput drops to 40Mbps from ~120Mbps.Enabling WAN traffic meter is needed to get SNMP data from WAN port.
View 1 Replies View Relatedwhat the maximum Data Througput can be for this router. Right now, the router is limiting my internet speed compared to what the cable modem can provide..So far, I know that when I connect my computer directly to the output of the Motorola Cable Modem and run a Speed Test on my Charter cable connection, the test shows ~ 50 Mbps for downloads and ~5 Mbps for uploads. That would be great, but I have multiple computers and need to use a router/gateway to feed my LAN. When I insert the RVS4000 router between modem and computer, the Speed Test results drop to ~ 16 Mbps for downloads and remain ~ 5 Mbps for uploads. During that test, there were no other computers online via the router. While 16 Mbps is not shabby, I would like to achieve the full value... is that possible?
Is the RVS4000 unit capable of 50 Mbps for 30 Mbps? How do I setup the router to achieve the maximum available download speed?There is a setup page for the router which has settings right now set at 50000 Kbps Upload and 60000 Kbps for Download; this implies to me that the router is capable of such speeds.
I have a Netgear CG3100 modem hooked up to a Netgear WNR2000 router. Both are sending out signals, the CG3100 on channel 11 at 40 Mhz and the WNR2000 on channel 1 at 20/40 Mhz. I keep the WNR for legacy devices while the CG is for N devices only. They don't seem to interfere with each other much.Currently my computer is the only device connected to the modem wirelessly, with the only wired connection being the router. As I write this, the connection has actually dropped to 26 Mbps in the Wireless Network Connection Status window. I understand that this number drops under network load, but there doesn't seem to be any at the moment. If I go into the control panel and simply click apply, the connection jumps back up to 150 Mbps. However, this always drops back down, sometimes immediately, sometimes after a few minutes. It usually settles down at 72 Mbps, sometimes 54 Mbps.My wireless adapter is an ASUS PCE-N13 with v3.2.7.0 Ralink drivers. OS is Windows 7 64-bit.
View 6 Replies View RelatedI have 100 Mbps Half Duplex on one side of the Switch. ( Autonegotiation disabled )I have 10 Mbps Full Duplex on the other side ( Auto-negotiation disabled ). Should the link come up on both sides
View 4 Replies View RelatedI have an RVS4000 V1 router connected to a Comcast Extreme 100 mbps cable modem.The port setting for the port (number 4) is 1000Mbps Full Duplex, auto Negotiate.why the RVS4000 is throttling the port?
View 3 Replies View RelatedMy RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!
I just upgraded my cable modem from the Motorola Sufboard 5120 to the DOCSIS 3.0 capable 6120. Provisioned it with Comcast and their "Blast" service (supposedly it caps at 16 down, 2 up).
I had, in the past, used my desktop via N-format wireless (DWA-525 N-format PCI adapter and DIR-655 N-format router) to do a speedtest.net test. I was getting 16 down and 2 up (as advertised). When I switched to the 6120, I did a speedtest.net test again to see what kind of gains, if any, I was getting. Turns out, I was getting 20+ down (nice improvement) and 1/2 Mbps up (a fourth of what I used to be getting?). Called Comcast. They "sent signals" (don't they always?) and claimed that it fixed it. My download speeds increased a smidge (about 22), but my upload speeds were still .5. Called Motorola, they had me do a few things and now I get 1 Mbps up and 27 - 30 down via wireless.
My download speeds are great. I'm content with that. If I hardwire from the cable modem directly to a ****py old laptop, a speedtest.net shows 4 Mbps up. So why do I get such a high upload speed when hardwired (4 Mbps), but a fraction of it (1/4th) when wireless? I'm not using any other devices to sap bandwidth (some are connected -- i.e. another desktop, my Droid phone, etc., but aren't actively pulling packets). And why would it go from 2 up (on my desktop via wireless in the past) to only 1 up (via wireless now) when the setup is the same across the board (as best I recall) other than upgrading my cable modem.
Since I get 4 up when hardwired straight off the cable modem, I assume my DIR-655 is slowing me down somehow. How to pick up the pace a bit? I've already tried the standard "power cycling", etc.
Oh, and the reason I go wireless -- my cable modem and wireless router are in my game room in the basement for my PS3. My desktop computer (and the wife's desktop computer) are two floors directly above it in our "office". Signal strength is "excellent" ... always has been. And again, pretty much everything is the same.
[URL]
The first router is wired to the DSL modem and works just fine as an access point with Internet access. The second router is wired from the first router using one of the 4 ports on both router hubs. The second router is visible but has no Internet. How to configure the second router regarding DHCP, LAN, WAN, DNS etc.
View 3 Replies View RelatedI have two matching N300 Belkin routers. The cable modem feeds into modem1 and modem1 feeds into modem2. I get a good wireless connection on modem1. Modem2 shows up on a wireless scan and it accepts the password. It however will not connect.
View 1 Replies View RelatedFor some time now I've used the USB port on RSP440's fitted into ASR9006's to load IOS with no problems.Recently I noticed that the ASR9001 USB port doesn't seem to work at all, which seems odd to me as I believe the 9001 uses the same card built into the chassis.All routers were running the same code version 4.3.0, and I was using the same memory stick?
View 1 Replies View RelatedI need to open ports 9080 and 5280 on my Cisco ASA 5505 firewall and despite doing everything I THINK I needed to do...when I run the utility to check from outside; it is NOT open....I utilize a website called [URL] (very good for these kinds of things) I have added the specific port(s) to my services so that I can CHOOSE them; added an ACE/ACL to; added incoming/outgoing rules to accomodate traffic to those ports....NOTHING.
View 7 Replies View Relatedi have a 100 mbps lan. but 1 computer works on only 10 mbps half duplex mode why??
View 4 Replies View RelatedI'm trying to configure Catalyst 2960 series 8 port switch in my office. I have just plugged in switch and started and then put Ethernet cable (which is coming from the wall port (LAN) into CONSOLE (switch). and connected my laptop's ethernet cable to switch's 1x por
View 16 Replies View RelatedHow do I disable the USB port in the 881 router?
881router#show usb port
Port Number: 0
Status: Disabled
Connection State: Disconnected
Speed: Full
Power State: ON
I've tried a few different ways unsuccessfully so thought I'd ask here.I'm trying to forward an outgoing port on a Cisco 800 series router. ie. When a user inside the network connects to the router on port 1234, it opens up the same port on a server on the Internet.
View 2 Replies View RelatedI have a Cisco 800 series ?I need to allow access to our local server from a specific range of external ip addresses.I can open port for all external ip using this command:
ip nat inside source static tcp <localserverip> <port> interface <interface> <port
But this is not secure as is..Do I then restrict and permit access using access-list? Or is there another way altogether?
Cisco Catalyst 2960 series,i want do a SNMP request over OID. When the output should be like this: Portnumber and VlanID. Is there a OID for this output?
View 1 Replies View RelatedI just setup my homelab today, after having Cat5e installed so I can run my servers and network equiptment over wired network as well as setting up a wireless system. I got everything setup and its going great I can access everything from my office now including a E4200 Linksys router that I setup to do RiP (was only choice pretty much, or NAT), and my 891 Cisco Router which is my internet connection.
I use to have the linksys setup to do port forwarding but now I need to figure out how to do it on the cisco 891 router via command line.
Below is my current configuration. I need to be able to access my server which is behind my router by Remote Desktop. I also have a web server, and the kids also play minecraft, and have a server setup so I need to be able to forward their port as well.
[URL]
Ths is from the link above, would I just do like that but then put in my IPs and is that my Private IP I use this or my public facing. Also he has "interface Dialer1 6881" again after the port in the second and third row. I dont really understand what they have there. I understand basic access list and such though I am extremely rusty.
!
ip nat inside source list 102 interface Dialer1 overload
ip nat inside source static tcp 10.0.0.2 6881 interface Dialer1 6881
[Code].....