according to [URL] enabling WMM should increase wireless performance. Although this article is rather old, how is the RV220W expected to behave?
In my case, speed measurements show a clear decrease in wireless performance when WMM is enabled.
For example:
WMM enabled - max 15MBits/s (ticked WMM checkbox - default settings)
WMM disabled - max 40MBits/s
I recently got a new modem/router device from my ISP and its wifi is fairly weak (no external antennas) especially in my basement. Since wifi is no longer an option and I only have one ethernet connection to my basement I was thinking of using my old router to distribute the one ethernet connection to multiple devices. Connecting my one ethernet connection to the old router, and its port#1 to my PC in the basement works without any meddling, but the speed has taken a significant hit. Before the second router I was getting ~30-40Mbps from my ISP. With the second router it is reduced to ~10-20Mbps. Both routers I assume are capable of at least 100Mbps (probably even 1Gbps?). The older router is a Linksys WRT54G which can do 54Mbps wirelessly so I assume it can exceed 10-20 wired.I tried giving the second router a static IP with DHCP off, but it did not seem to make a difference. I don't know if I set it up correctly, however. The modem/router uses 192.168.0.xxx while the second uses 192. 168. 1.xxx so I do not think there is any conflicts in the DHCP.
View 3 Replies View RelatedAt the recommendation of a tech, I ran a speed test (speedtest.net) on my system with my N600 in place. The upload speeds averaged out to 0.21mbps. I took the router out of the system and the speed climbed to an average of 0.37. What is the problem with the router and what need I do to boost the upload speed with it in place?
View 1 Replies View RelatedApparently one of my two ISPs,CenturyLink, supports 6rd connections to IPv6.
This is supported natively on my Q1000 ActionTec modem, however my modem is in "transparent bridging" mode, so that the RV042 v3 can be the only router.
how to configure the RV042 to operate in this manner.
Per the CenturyLink FAQ: the IPv6 address space is:
2602::0 /24
Most importantly, can I do this WITHOUT buying a new modem.
I'm running FW 1.02.01 (23) and I'm having problems with the DNS proxy. I have DNS Proxy enabled for my DHCP server on the router and I have my dns server programmed into the global dns location. I cannot ping any DNS names for my IPSEC VPN tunnel.
View 2 Replies View Relatedi have gotten a question from a partner in regards to the throughput on both LAN and WAN on the SRP541W. I can't really find that on the datasheet.
View 4 Replies View RelatedI have a wireless router at home and i have a PC and a mac enabled for it. I have recently bought an IPAD and i can't connect for some reason. When asked for the password it doesn't enable me to connect so I'm worried that i've forgotten my password.
View 4 Replies View RelatedI have a Belkin F5D7634-4 v2 (01) and when using bittorrent I cannot enable udp connections. In Virtual Server, both TCP and UDP are enabled - why won't it connect?
View 3 Replies View Relatedwhich 800 series routers allow 20 Mbps throughput across the WAN port? I have a cable modem that outputs this speed but am having difficulty finding a router that will accept this throughput across the WAN port.
View 21 Replies View Relatedwhat is the throughput of the 1941 and 3945 series routers, i didn't find this info in the datasheet for both!
View 2 Replies View RelatedWhat is the WAN to LAN Throughput of RV042 router with QoS and SPI enable?
Will the RV042 router able to support a 60Mbps down 3Mbps up Internet connection with QoS enable and SPI enable without slowing down the connection?
When WAN traffic meter is enable on RV180 router maximum throughput drops to 40Mbps from ~120Mbps.Enabling WAN traffic meter is needed to get SNMP data from WAN port.
View 1 Replies View Relatedwhat the maximum Data Througput can be for this router. Right now, the router is limiting my internet speed compared to what the cable modem can provide..So far, I know that when I connect my computer directly to the output of the Motorola Cable Modem and run a Speed Test on my Charter cable connection, the test shows ~ 50 Mbps for downloads and ~5 Mbps for uploads. That would be great, but I have multiple computers and need to use a router/gateway to feed my LAN. When I insert the RVS4000 router between modem and computer, the Speed Test results drop to ~ 16 Mbps for downloads and remain ~ 5 Mbps for uploads. During that test, there were no other computers online via the router. While 16 Mbps is not shabby, I would like to achieve the full value... is that possible?
Is the RVS4000 unit capable of 50 Mbps for 30 Mbps? How do I setup the router to achieve the maximum available download speed?There is a setup page for the router which has settings right now set at 50000 Kbps Upload and 60000 Kbps for Download; this implies to me that the router is capable of such speeds.
My RV110W is only a few months old and apparently started ginvg me issues shortly after I got it. Since it was new, however, I only recently suspected it as the culprit!
I have a simple home/small business setup. A single PC wired into the lan and a handful of occasional use laptops & Android phones/tablets and a Playstation.My connection is a 30M down / 5M up cable link. I have a UBEE DOCSYS 3.0 cable modem operating in passthru mode to my RV110W.
Over the course of several days, thruput drops from the measured 30/5 down to as low as 1/whatever. Rebooting the RV110W restored full speed. The UBEE has never been rebooted during this time. Connecting my wired desktop PC directly to the UBEE modem give me the full 30 downlink speed even when the RV110W perfomance has dropped to 5 or even 1.
I am using onle a single wireless LAN, no logging turned on, no VPN, no other 'tuning of settings.As it is, this device must be rebooted every few days to restore full network speed. This is unacceptable, of course - especially from a small business class device!
As soon as I add the interfaces of the router to security zones it significantly drops speed on WAN interface, below 1 Mbs. I noted this because I wasn't able to watch youtube. Moreover the bandwidth test from speedtest.net hangs and doesn't come to a result. Here below is the diagnostic example while doing that test. The question is what is going on? I have two iPhones and three computers in my network, that's it. My ISP bandwidth is 10 Mbs, so is this the router hardware limitations, or kind of malfunction or some misconfiguration down here? What could be done here ?
View 4 Replies View Relatedwhat exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedI am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedPicked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies View RelatedIs there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies View Relatedi have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedHaving a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies View RelatedI have a netgear n600 router and in the room its in i get around 50 down and 12 up but in other rooms it drops significantly(the highest ive gotten is 11 down in other rooms). is there any setting i can go into.
View 3 Replies View RelatedI have a Linksys E3200 router and it seems to work fine with my laptop, but doesn't work well with the desktop at all. I can't run a cable from the router to the desktop because of distance?on [URL], my laptop gets around 45 Mbps download rate and 5 Mbps upload rate while my desktop would get about 1 Mbps download and 2 Mbps upload, while both computers are at the same exact location. I have tried using two wireless LAN cards for my desktop in the past and they did not give me good internet at all. I am now using a NETGEAR WNDA3100v2 USB Adapter and it gives an extremely weak signal as well. I have tried configuring it and the router a number of times and nothing significantly changed the signal. Since all of these devices have failed to give me a good signal?
View 4 Replies View RelatedI got my Brand new xps 15 yesterday, It works fine, looks great, I'm overall satisfied with it. (even though it gets warm all the time)
Problem is, the WIFI doesn't work well at all, I'm 2 meters from my box right now, And I'm not experiencing any problems, but as soon as I get upstairs in my bedroom, my signal speed drops significantly, I can't even load a you tube video, I was downloading a game from steam yesterday, and the dl speed dropped to 6mb/s!! That's awful, If this problem can't be fixed, I'll be returning mine, and won't buy any other Dell product, I don't see how a laptop that pricey can have that kind of problems. ( because I heard I wasn't the only one, a lot of people have the same problem).
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies View RelatedNothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies View RelatedWhen someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies View RelatedWhere I can find the MIB files for RV220W router?
View 2 Replies View RelatedI'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]