Cisco Routers :: RV220W Just Disappears
Jun 23, 2012
Having a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies
ADVERTISEMENT
Feb 1, 2013
I just bought a N750 DB router. On boot up, the 5Ghz side will show up for about 20-30 seconds and then it just "disappears". I was even able to connect to it @ 300mb with my laptop. The 2.4Ghz shows up just fine.
View 3 Replies
View Related
Apr 2, 2012
what exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies
View Related
Aug 24, 2012
I am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies
View Related
Jul 3, 2012
Picked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
View 9 Replies
View Related
May 15, 2012
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
View 5 Replies
View Related
Dec 12, 2012
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
View 8 Replies
View Related
Sep 28, 2011
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies
View Related
Nov 27, 2011
Is there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies
View Related
Jul 22, 2011
i have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies
View Related
Jul 19, 2012
I set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies
View Related
Jan 26, 2012
I am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies
View Related
Nov 20, 2012
Nothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies
View Related
Jan 31, 2013
When someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies
View Related
Sep 26, 2011
Where I can find the MIB files for RV220W router?
View 2 Replies
View Related
Aug 5, 2011
I'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
View 12 Replies
View Related
Apr 30, 2013
I'm using a RV220W in my home office. Before this router I was. using a Sitecom router which did not cause any problems. I have setup a home network. The RV220W connects to the provider modem. The client components connect to the RV220W. Which acts as DHCP gateway. The DHCP features of the modem are disabled. I have assigned all network client devices to the same workgroup. I have to windows 7 PC's. one of them acts as fileserver. when trying to acces it from the other fixed PC or via a laptop the fileserver is visible but not accessable. I can not open it and access the shared folders.It has worked for a brief moment, but without changing any settings it stop working. I have never had accessability problems with the sitecom router. I have installed the latest firmware and tried rebooting the router several times. I have also started again with the factory defaults.
View 3 Replies
View Related
Jan 8, 2012
I have a cisco RV220W router used in a home environment. Recently I purchased a Siemens Gigaset A 580 IP phone. It works OK so far but I would like to optimize the configuration for VoIP traffic and apply QoS for VoIP on this router. Any guide with the recommended configuration and preferred settings of the same? I have not used QoS previously
View 1 Replies
View Related
Jul 18, 2011
I have an Cisco RV220W and I can’t connect to web interface. The router is new, I receive the error in Mozilla: Cannot communicate securely with peer: no common encryption algorithm(s). I used also Internet Explorer, Chrome , I tried to disable SSL 3.0, TLS 1.0 but the problem persist. The PC obtained IP address from the router, I have ping on it ,also the SSID is up with open network I reset to factory default but the problem persist.
View 2 Replies
View Related
Mar 23, 2012
I recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
View 3 Replies
View Related
Aug 29, 2011
I do you not think the RV220W needs to have better E-mail support that the feature it supports at present?No SSL support at all. The only setting for authentication is: Login Plain or CRAM-MD5. Every mail server I use now, supports SSL as the default authentication and not CRAM or Plain, this makes the E-mail feature useless. [code]
View 1 Replies
View Related
Nov 8, 2012
I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
View 5 Replies
View Related
May 16, 2012
I have 5 public, static IP's provided by my ISP. I read on another page that to use the 2nd, 3rd, 4th and 5th IPs, I must first 'register' them by entering them on the WAN page and I must wait until I can successfully PING them from an external network. Then I can set the WAN IP back to the one I want to use to administer the router. Then I can use those other IP's on the various Access Rules or Port Forwarding pages where there is a spot to enter 'alternate WAN IP address'. I'm trying to determine if this is true because I'm having a heck of a time getting port forwarding to work. My BIOS is 1.0.3.5.
View 7 Replies
View Related
Aug 29, 2011
I am trying to setup logging on my router. I want to use my gmail account / gmail SMTP server to send emails.
Does the router support TLS for SMTP?
Oh - and I also get the "critical error" page. I get it when I try to un-check the send logs checkbox in the remote logging management page.
View 5 Replies
View Related
May 15, 2011
I'm relatively new to establishing VPN connections and I'm having one heck of a time getting everything configured.I'm setting up a RV220W at the office and trying to get VPN steup. I've have gotten Quick VPN connections working using the QuickVPN software. I've given up for now on IPsec VPN connactions and will come back to these later.What I'd like to get setup is the SSL VPN connections using the Win7 built in VPN client. Is this even possible? I initially tried to connect to the VPN via the SSL Web access but I cannot get the software/divers to install on any of the 3+ Win7 64 bit machines I tried.So can the SSL VPN on the RV220W be setup to connect to with the Win7 VPN Client using SSTP?
View 6 Replies
View Related
Sep 16, 2012
Just purchased an RV220W for a customer to replace a WRVS4400N that had no support for One-to-One NAT and have found the One-to-one NAT for this router is only marginally better.
I have three WAN addresses and three devices to map them to. With the RV0xx I've used the following configuration over a dozen times.
WAN Address 1 - the router's public address Port forward HTTP, HTTPS, and SMTP to Windows Small Business Server 2011 Email and Remote Web Access are accessible at remote.company.com
WAN Address 2 One-to-one NAT to private IP address of Ubuntu Server Add the following access rules: Deny allAllow HTTP from any to private IP address of serverAllow SSH from my company's static IP to private IPAllow FTP from my company's static IP to private IPCompanies website is accessible at company.com and I can update the website with SSH and FTP
WAN Address 3 One-to-one NAT to private IP address of the Hyper-V server's Intel RMM module (Lights out remote management) Add the following access rules: Deny allAllow HTTP, HTTPS, and all RMM ports from my company's static to the RMM modules private IPI can access server at rmm.company.com from my companies network connection
My problems are as follows:
The One-to-one NAT option now requires you to specify the service you'd like to forward (Note: service, not services)If you select the Any service which is the only way I can see to have more than one service, there is no way to add any specific Allow or Deny rules because the Destination box is grayed out on the access rules page.This results in my Ubuntu server only having HTTP forwarded to it and my RMM module having all ports opened up to any IP address. There must be some way around this! I don't understand why the Destination IP option is greyed out for all Inbound access rules. I have been using this same configuration with the Cisco RV0xx, many Sonicwall firewalls, as well as several Cisco ASAs. Obviously this is not an ASA but this implementation of One-to-one NAT is useless!
View 5 Replies
View Related
Aug 1, 2012
I have 2 ssid signals setup at my workplace.
the 2nd one is for all guests and it's isolated from the lan+trusted(1st one) with a vlan feature.
the 1st one is for all trusted devices over wifi. the wifi channel is setup to allow mac addresses of the two asante security cameras. the cameras upload videos to an ftp on my server. the two will connect to the router at first, I can ping them or see them in 'my network'. give it a little time and they disappear. then I have to power off/on the router or the cameras to make them work for a few minutes. the process repeats.
the cameras make lots of connections to the ftp server. I'm suspecting they're flooding the router and it blocks them. occasionaly they will come back for a minute or two and disappear again as if blocked/unblocked.
I added their mac addresses in hopes of making them 'trusted' devices. I've tried them on both ssids. I checked and unchecked firewall/security checks and icsa settings. all other devices I tried, multiple phones and laptops work without problems on both ssids and they don't get blocked.
View 5 Replies
View Related
Oct 10, 2011
I have and D-Link modem which is bridged and a PPPoAPPPoE profile set up on the RV220W for my ADSL2+ connection.I cannot for the life of me find anywhere in the routers config web pages to tell the modem to disconnect or reconnect the connetion to the ISP.The reason I want this is because I need to make sure the correct signaling is sent before the connection is stopped so that the exchange doesnt see this as a drop out and reduce our line speed to compensate.
View 1 Replies
View Related
Jan 1, 2013
We are running an RV220W at the latest firmware (1.0.4.17). Due to certain internal activity we had to add a few firewall rules. Once we exceeded 10 firewall rules we could not reorder them. The reorder page showed the first 10 rules OK, but when you display the next screen (for rules 11 upward) the order is different and any changes do not appear persistant. Therefore you can change the order of the first 10 rules, but not from 11 onwards.
View 5 Replies
View Related
May 12, 2013
I just received and installed my RV220W today. Everything was working fine. I was down to configuring SSL VPN as my last step. I was reading through the documentation and than went back to the management console to make a change. The session timed out. When it prompted me to login again I keep getting a message on the screen "i18nHTMLMissing", nothing else. (Ruby on Rails Error?) I can't seem to login anymore. All logins result in this message. I have tried from multiple devices with the same result.
View 5 Replies
View Related
Jun 10, 2013
I logged into my RV220W to backup the config before we upgrade our network and for some reason the navigation bar is not showing on the left, all that is showing there is Change Password, which does nothing when I click on it. The links on the Getting Started page (i.e. Initial Settings-Configure WAN) do take me to the associated link but I can not get to any of the settings I need such as Administration etc.
View 4 Replies
View Related
Sep 7, 2011
My ISP sends various services through VLAN. Internet, TV and Telephone.Now I wonder, is it possible to use this router to distribute these VLANs through the wan port to eg my IPTV box?
View 5 Replies
View Related
Jan 2, 2013
I have a Cisco RV220W router (firmware version 1.0.4.17).
I would like to have two separate networks with the following specifications:
Netwrork1: address range for the network is 192.168.0.1-254. All devices should be able to reach eachother within this network and connect to the internet either on LAN or through Wifi. From this network I should also be able to reach the device management page of the router. Also the devices should get the ip addresses throgh DHCP.
Network2: address range for the network is 192.168.5.1-254. All devices within this network should not be able to reach the devices in network1. All devices on this network should reach the internet through Wifi only. Device management page should not be available on this network.
I have configured the router as shown in the attached screenshots but the problem is that in Network2, devices get IPs from the 192.168.0.1-254 range and not from the 192.168.5.1-254 range. Also there is no internet on these either.
View 8 Replies
View Related
