I do you not think the RV220W needs to have better E-mail support that the feature it supports at present?No SSL support at all. The only setting for authentication is: Login Plain or CRAM-MD5. Every mail server I use now, supports SSL as the default authentication and not CRAM or Plain, this makes the E-mail feature useless. [code]
View 1 RepliesI am trying to setup logging on my router. I want to use my gmail account / gmail SMTP server to send emails.
Does the router support TLS for SMTP?
Oh - and I also get the "critical error" page. I get it when I try to un-check the send logs checkbox in the remote logging management page.
I am trying to open a support ticket with Cisco for an SMB router (RV220W) using the link: URL
When I reach the point when I am asked to supply the serial number of the device I do and then I get an error message that the serial number cannot be found in some database. Am I doing something wrong? Am I supposed to register this product's serial number somewhere?
Cisco RV220W works in 2.4GHz or 5GHz.There is any plan to support these bands simultaneously?
View 1 Replies View Relatedget a status on Mac Lion and/or Windows 7 64-bit SSL VPN support for the RV220W? QuickVPN (for Windows 7 64-bit users) and IPSecuritas (for Mac Lion users) are our current workarounds, but for folks that use/own their own equipment we prefer SSL VPN. This is why we retired our WRVS4400N v2 for the RV220W.
View 3 Replies View RelatedI have a question about NAT behavior on FWSM 4.0. The problem is email server (Company A) cannot connect to email gateway (Company B) on the outside network and it randomly happen. I got this error from server guy "Detail: xlate has blocked the connection between A’s mail gateway and B’s mail gateway". It work fine again after clear xlate on firewall. [code]
1. How FWSM create xlate table like that? I mean it look like NAT0 for 158.137.21.26 but it doesn't has any nat rule for 158.137.21.26 on firewall.
2. What does it mean "connections 24" at the first of line? In the normal time, I only see the connections is 0 like the second line of xlate
3. After clear xlate global 158.137.21.26, the first line of xlate table is gone then email server can connect each other. Does is a bug on FWSM? or This is a normal NAT behavior of FWSM.
I deleted an incoming email titled troy from my email inbox by mistake I need to recover this email as it came from my son in bali [URL] edited by moderator: Deleted Email address to prevent Spam
View 1 Replies View RelatedNo School havn't own email server, Just we want email within the Lab. (There are 20 PCs on all PCs Windows XP (Service Pack 2) & MS Office 2003 installed.Now tell me how can we send/receive email via using outlook.
View 1 Replies View RelatedWhere/how do we setup an SRP527W to send email notifications? Can't seem to locate the setting when logged in as admin.
View 1 Replies View Relatedwhat exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedI am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedPicked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies View RelatedIs there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies View Relatedi have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedHaving a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies View RelatedJust installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.
View 0 Replies View RelatedWhy does err 0x80040900 show up sometimes when tx/rx email? I use a WRT54GS linksys router. I have more than one computer which use Microsoft Outlook 2003 to check email accounts. When the error shows up I can ping the server no problem. The error sometimes goes away and comes back randomly.
View 2 Replies View RelatedI am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies View RelatedNothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies View RelatedWhen someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies View RelatedWhere I can find the MIB files for RV220W router?
View 2 Replies View RelatedI'm an IT professional with more than 10 years experience. I have spent last 5 days trying to figure out why the wifi connection to this router is so slow, but still no luck. I'm getting only 13Mbps even if my laptop is next to the router! (wired connection worked ok)
I have tried all sort of setting combinations, 2.4GHz/5GHz; N only/ G,N Mixed; Auto/20MHz bandwidth; different channels; WPA2 encrypted vs open; disable firewall; wmm enabled/disabled; 1.0.0.26/1.0.1.0 firmware... no matter what I try, I always get only 10 - 15Mbps speed.
Once I replace this router with my old router, it worked perfectly --- getting 70 - 80Mbps with exactly the same testing environment and configuration.
I really expect this router to offer much faster wireless speed according to this review: [URL]
I'm using a RV220W in my home office. Before this router I was. using a Sitecom router which did not cause any problems. I have setup a home network. The RV220W connects to the provider modem. The client components connect to the RV220W. Which acts as DHCP gateway. The DHCP features of the modem are disabled. I have assigned all network client devices to the same workgroup. I have to windows 7 PC's. one of them acts as fileserver. when trying to acces it from the other fixed PC or via a laptop the fileserver is visible but not accessable. I can not open it and access the shared folders.It has worked for a brief moment, but without changing any settings it stop working. I have never had accessability problems with the sitecom router. I have installed the latest firmware and tried rebooting the router several times. I have also started again with the factory defaults.
View 3 Replies View RelatedI have a cisco RV220W router used in a home environment. Recently I purchased a Siemens Gigaset A 580 IP phone. It works OK so far but I would like to optimize the configuration for VoIP traffic and apply QoS for VoIP on this router. Any guide with the recommended configuration and preferred settings of the same? I have not used QoS previously
View 1 Replies View RelatedI have an Cisco RV220W and I can’t connect to web interface. The router is new, I receive the error in Mozilla: Cannot communicate securely with peer: no common encryption algorithm(s). I used also Internet Explorer, Chrome , I tried to disable SSL 3.0, TLS 1.0 but the problem persist. The PC obtained IP address from the router, I have ping on it ,also the SSID is up with open network I reset to factory default but the problem persist.
View 2 Replies View RelatedI recently installed a new 220W with the sole intention of setting up the PPTP server. I got the router installed and working but cannot get the PPTP server working. Also when i configure a block of IP address from my lan for the server it tells me i cannot use that subnet? i have set it up this way with other routers ( RV042 ) with no issues.
firmware is 1.0.0.26
I'm trying to setup this router with my IP range 192.168.100.1 to 192.168.101.254 but if I try to enter a subnet mask other than 255.255.255.0 I get the error - Invalid subnet mask. It should be 255 for given class of IP address at 255.255.xxx.0.
Every other device on my network allows that subnet mask, why not this router, it's stopping access from my 192.168.101.x devices.
I have 5 public, static IP's provided by my ISP. I read on another page that to use the 2nd, 3rd, 4th and 5th IPs, I must first 'register' them by entering them on the WAN page and I must wait until I can successfully PING them from an external network. Then I can set the WAN IP back to the one I want to use to administer the router. Then I can use those other IP's on the various Access Rules or Port Forwarding pages where there is a spot to enter 'alternate WAN IP address'. I'm trying to determine if this is true because I'm having a heck of a time getting port forwarding to work. My BIOS is 1.0.3.5.
View 7 Replies View RelatedI'm relatively new to establishing VPN connections and I'm having one heck of a time getting everything configured.I'm setting up a RV220W at the office and trying to get VPN steup. I've have gotten Quick VPN connections working using the QuickVPN software. I've given up for now on IPsec VPN connactions and will come back to these later.What I'd like to get setup is the SSL VPN connections using the Win7 built in VPN client. Is this even possible? I initially tried to connect to the VPN via the SSL Web access but I cannot get the software/divers to install on any of the 3+ Win7 64 bit machines I tried.So can the SSL VPN on the RV220W be setup to connect to with the Win7 VPN Client using SSTP?
View 6 Replies View Related