I am trying to setup logging on my router. I want to use my gmail account / gmail SMTP server to send emails.
Does the router support TLS for SMTP?
Oh - and I also get the "critical error" page. I get it when I try to un-check the send logs checkbox in the remote logging management page.
On a RV220W (1.0.3.5) I keep seeing the following error in the logs multiple times:
[Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
What this error is all about and how to fix it?
Looking at the logs RV220W I can read the following lines:
[rv220w]Fri Aug 19 18:28:54 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378400
[rv220w]Fri Aug 19 18:30:39 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378200
[rv220w]Fri Aug 19 19:23:04 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378e00
[ code] ....
What are they?? and what should be done ????.
I do you not think the RV220W needs to have better E-mail support that the feature it supports at present?No SSL support at all. The only setting for authentication is: Login Plain or CRAM-MD5. Every mail server I use now, supports SSL as the default authentication and not CRAM or Plain, this makes the E-mail feature useless. [code]
View 1 Replies View RelatedAny way to get the DIR-655 to e-mail logs? I have all the e-mail settings set properly, but when I request the logs to be e-mailed, I never get anything. Its not in a spam folder either.I do have the DIR-655 behind a 2wire router/DSL modem. I don't know if this is the problem, but I can send and receive e-mails from my computer which is connected to the DIR-655, so I don't think that is the problem.
View 6 Replies View RelatedDIR-615, HW rev. H1, FW v8.02
As the subject says... Sending logs using "On schedule" option doesn't work. I have my own personal email server I used to test this. When the router time reaches the defined "Start time" nothing happens. I tried both time formats (12h, 24h). The router does NOT initialize the process of sending the email. I see that in my server mail logs. If sent manually from Status -> Logs -> Email now, it works. If sent using "On Log Full" option, also works.
I absolutely need to collect the router logs and send them to a syslog daemon or via email.
View 9 Replies View RelatedHow i can transfer the router logs to email address.Wev are using the router 2600.
View 5 Replies View RelatedI have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.The log says that it's failing each time it attempts. I have scoured the internet and I cannot find a solution that will work for me. I have found some talk of adjusting an MTU setting which is supposed to be located under the firewall / general tab.
View 1 Replies View RelatedI have turned on 'Local log' and 'output blocking event log' on my WRVS4400N v2 with latest fw.When I am clicking 'view log' button I can't see anything in empty fields. When I am trying to change logs genre I have empty fields all time.
View 1 Replies View RelatedI have in my work RV016 10/100 16-Port VPN Router, working Ok and connected with 3 ADSL internet lines.
1- The problem is that when any line disconnect from internet it supposed to log this disconnection in internet in system log but it does not
2- I can't understand the option of sending mail with the logs, does it send when i press the button EMAIL LOG NOW, or it supposed to send when any log is added? and how to configure it.
I updated my RV180W to the latest firmware and found that port forwarding works I started using it.I've just noticed that since changing over to the RV180W, my Apacher server logs show the router's IP address instead of the remote IP address - every remote request appears to come from 192.168.0.1.
How do I get it to forward the remote IP.
I have RV042 V01 and V03 and RV082 V03.I'm wondering if there's a difference between the default actions taken by the "Logs" interfaces?
In the case of the V01 systems, it appears that I get a Security Notification every hour.In the case of the V03 system, it appears that I rarely get a Security Notification.
I have a question about NAT behavior on FWSM 4.0. The problem is email server (Company A) cannot connect to email gateway (Company B) on the outside network and it randomly happen. I got this error from server guy "Detail: xlate has blocked the connection between A’s mail gateway and B’s mail gateway". It work fine again after clear xlate on firewall. [code]
1. How FWSM create xlate table like that? I mean it look like NAT0 for 158.137.21.26 but it doesn't has any nat rule for 158.137.21.26 on firewall.
2. What does it mean "connections 24" at the first of line? In the normal time, I only see the connections is 0 like the second line of xlate
3. After clear xlate global 158.137.21.26, the first line of xlate table is gone then email server can connect each other. Does is a bug on FWSM? or This is a normal NAT behavior of FWSM.
if i flash my firmware on my router, can i still view the router logs before the flash? i heard that .logs can be on the ram of the router.
View 1 Replies View RelatedI deleted an incoming email titled troy from my email inbox by mistake I need to recover this email as it came from my son in bali [URL] edited by moderator: Deleted Email address to prevent Spam
View 1 Replies View RelatedNo School havn't own email server, Just we want email within the Lab. (There are 20 PCs on all PCs Windows XP (Service Pack 2) & MS Office 2003 installed.Now tell me how can we send/receive email via using outlook.
View 1 Replies View RelatedWhere/how do we setup an SRP527W to send email notifications? Can't seem to locate the setting when logged in as admin.
View 1 Replies View Relatedwhat exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedI am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedPicked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies View RelatedIs there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies View Relatedi have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedHaving a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies View RelatedJust installed a RV042 with dual wan connections. Would like to make the WAN 2 (new cable modem as well) the primary connection over WAN1 (DSL), however whenever I switch from WAN1 to WAN2 in Smark Link set up, our email server will not send mail out, even though nothing is blocking the connection.
View 0 Replies View RelatedWhy does err 0x80040900 show up sometimes when tx/rx email? I use a WRT54GS linksys router. I have more than one computer which use Microsoft Outlook 2003 to check email accounts. When the error shows up I can ping the server no problem. The error sometimes goes away and comes back randomly.
View 2 Replies View RelatedI am unable to make UPnP to work on the RV220W. I am forced to use port forwarding.
View 10 Replies View RelatedNothing happens when clicking the SAVE button after making changes on the VLAN Membership screen when using IE9, but it work fine with IE8. Any problems using IE9 during configuration?
View 4 Replies View RelatedWhen someone downloads a file, or similar, there seems to be no, or very little, room for other requests. I've even tried to be the only one on the network, start a download (from ex. Intel) and then tries to access a simple website, almost only text, and its extreemly slow. I hav ethe latest firmware, a windows domain network and the routers is not acting as dhcp server.
View 4 Replies View Related
