On a RV220W (1.0.3.5) I keep seeing the following error in the logs multiple times:
[Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
What this error is all about and how to fix it?
I am trying to setup logging on my router. I want to use my gmail account / gmail SMTP server to send emails.
Does the router support TLS for SMTP?
Oh - and I also get the "critical error" page. I get it when I try to un-check the send logs checkbox in the remote logging management page.
Looking at the logs RV220W I can read the following lines:
[rv220w]Fri Aug 19 18:28:54 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378400
[rv220w]Fri Aug 19 18:30:39 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378200
[rv220w]Fri Aug 19 19:23:04 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378e00
[ code] ....
What are they?? and what should be done ????.
I just received and installed my RV220W today. Everything was working fine. I was down to configuring SSL VPN as my last step. I was reading through the documentation and than went back to the management console to make a change. The session timed out. When it prompted me to login again I keep getting a message on the screen "i18nHTMLMissing", nothing else. (Ruby on Rails Error?) I can't seem to login anymore. All logins result in this message. I have tried from multiple devices with the same result.
View 5 Replies View RelatedWhen I access setup on an RV220W with Internet Explorer, Mozilla or Safari the following message always displays:
"There is a problem with this website's security certificate. The security certificate presented by this website was not issued by a trusted certificate authority. The security certificate presented by this website was issued for a different website's address."
I access the router by clicking on "Continue to this website (not recommended)."
This also happens anytime a URL filter is triggered by a client. I.e., clients do not see the "Blocked by Cisco Firewall" message unless they also click on the "Continue to this website (not recommended)." option.
Even worse, when I attempt to connect as a VPN, the SLLVPN applet gets java connection refused. This is why I bought this thing!
What do I need to do to fix all these certificate related errors?
I am locked out of the rv220w. After typing in username and password into the admin page I get "i18nHTMLMissing". I can't clear the error, even after a reboot/reset of the router. Any wat other than a factory reset? This is a brand new box .
View 1 Replies View RelatedWhat does this error message mean? What is wrong? Appears when adding a new One-To-One NAT rule. The first rule is OK. When I try to add a rule nr. 2, this error message occures.
View 3 Replies View RelatedI just got myself a Cisco RV220W, connected my laptop to configure it. I receive an IP adress by DHCP (192.168.1.x) and can ping the router (192.168.1.1). However, when I try to connect to the router by the web interface, I receive this message in my browser (Chrome):
The webpage at https://192.168.1.1/ might be temporarily down or it may have moved permanently to a new web address. Error 113 (net::ERR_SSL_VERSION_OR_CIPHER_MISMATCH): Unknown error.
In FireFox: Secure Connection Failed An error occurred during a connection to 192.168.1.1. Cannot communicate securely with peer: no common encryption algorithm(s). (Error code: ssl_error_no_cypher_overlap)
In IE9: I get no error message, the page never loads
Is it DoA or how to get connected to the web interface?
I try to connect to RV220W with windows 7 client but I fail : error 789. I compare again and again pre shared key, but it doesn't change anything. How to connect to RV220W with IPsec client ?
View 4 Replies View RelatedWe are using almost 10 Nexus 5k in our DC currently we are getting same error logs in all Nexus 5k." ntpd[4746]: ntp:time reset +0.279670 s " ,Is it major error or just for reset time?
View 1 Replies View RelatedI have problem with ACS 5.0 on reporting. On "Monitoring and Report" page in Faverite Reports when i clicking on "Authentications - RADIUS - Today", My browser displays error "Error while reading skin-access.config. Please make sure the file exists and conforms to the schema specified"
I must also mention that I never upgraded the version of ACS from 5.0 also from command line all the acs services are running. It is running on CISCO 1120 Secure Access Controll Server apliance.
My second question is can I upgrade the version of ACS to 5.4 with Cisco Secure ACS 5 Base License?
%SYSTEM_CONTROLLER-SP-3-ERROR: Error condition detected: TM_DATA_PARITY_ERROR Feb 2 10:57:09.602 EST: %SYSTEM_CONTROLLER-SP-3-EXCESSIVE_RESET: System Controller is getting reset so frequently
Cisco Internetwork Operating System Software
IOS (tm) s222_rp Software (s222_rp-IPSERVICES_WAN-M), Version 12.2(18)SXF15a, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2008 by cisco Systems, Inc.
Compiled Mon 20-Oct-08 19:20 by kellythw
Image text-base: 0x40101040, data-base: 0x42951080
[code]....
I am tryign to join my first AP to the 5508 and am gettign this error int he logs.
*Dec 07 10:42:31.067: %DTL-3-NPUARP_ADD_FAILED: dtl_arp.c:2280 Unable to add an ARP entry for 0:0.0.0 to the network processor. entry does not exist
The management Interface is on the the same vlan as the AP , both untagged ports. the AP gets an ip address from my dhcp server.
We are getting some error logs on Nexus VDC,as follows:2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times 2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times 2012 Nov 23 08:49:11 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 6 times2012 Nov 23 08:50:21 N7K_B-Network_Center_B %$ VDC-3 %$ last message repeated 7 times.
View 1 Replies View RelatedWe use C2950G switches with IOS 12.1(22)EA12 . Switches are set up to send logs to a server (informationnal level). On this server, we receive many of logs from those switches, but none about interfaces errors (even if interfaces statistics show interfaces errors). On C3548 switches it's work fine.How should I be sure the set up of switches is correct ? Why do I never receive messages as %LINK-4-ERROR:[char] is experiencing errors ?
View 2 Replies View RelatedI m getting below error messages in show logs -
Aug 12 15:30:57.127 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:02.175 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:08.219 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:10.239 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
there is no error messages related to PSU in "show env all " log .
here is show version -
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by cisco Systems, Inc.
[Code] ....
We are getting some error logs on Nexus switch 7K.
Loggs:
----------
2012 Oct 30 22:36:07 SWITCH %CMPPROXY-STANDBY-2-LOG_CMP_UP: Connectivity Management processor(on module 6) is now UP
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-GSYNC_SNAPSHOT_SRVFAILED: Service "ipqosmgr" on active supervisor failed to sto
re its snapshot (error-id 0x40480005).
2012 Oct 30 22:36:40 SWITCH %SYSMGR-2-STANDBY_BOOT_FAILED: Standby supervisor failed to boot up.
2012 Oct 30 22:36:42 SWITCH %PLATFORM-2-MOD_REMOVE: Module 6 removed (Serial number JAF1550ATBR)
2012 Oct 30 22:42:08 SWITCH %BOOTVAR-5-NEIGHBOR_UPDATE_AUTOCOPY: auto-copy supported by neighbor supervisor, starting
[code]....
I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.The log says that it's failing each time it attempts. I have scoured the internet and I cannot find a solution that will work for me. I have found some talk of adjusting an MTU setting which is supposed to be located under the firewall / general tab.
View 1 Replies View RelatedI have turned on 'Local log' and 'output blocking event log' on my WRVS4400N v2 with latest fw.When I am clicking 'view log' button I can't see anything in empty fields. When I am trying to change logs genre I have empty fields all time.
View 1 Replies View RelatedI have in my work RV016 10/100 16-Port VPN Router, working Ok and connected with 3 ADSL internet lines.
1- The problem is that when any line disconnect from internet it supposed to log this disconnection in internet in system log but it does not
2- I can't understand the option of sending mail with the logs, does it send when i press the button EMAIL LOG NOW, or it supposed to send when any log is added? and how to configure it.
I updated my RV180W to the latest firmware and found that port forwarding works I started using it.I've just noticed that since changing over to the RV180W, my Apacher server logs show the router's IP address instead of the remote IP address - every remote request appears to come from 192.168.0.1.
How do I get it to forward the remote IP.
I have RV042 V01 and V03 and RV082 V03.I'm wondering if there's a difference between the default actions taken by the "Logs" interfaces?
In the case of the V01 systems, it appears that I get a Security Notification every hour.In the case of the V03 system, it appears that I rarely get a Security Notification.
if i flash my firmware on my router, can i still view the router logs before the flash? i heard that .logs can be on the ram of the router.
View 1 Replies View Relatedwhat exactly is QuickVPN?Is it a IPSec VPN?Is it a PPTP?Is it a SSLVPN?can I resolve my local hostnames? That means, can I configure a lokal DNS Server?
View 3 Replies View RelatedI am trying to setup and configure a VPN on the RV220W that uses IPSEC so I can use the Cisco VPN Client I use at work, I have gone through the user manual 11 or 12 times now but still cannot work it out. I cannot find where on the Rv200W iset up the phase 1 authentication username and password which will then lead me onto the phase 2 stage of asking for a username password to allow me access.
View 8 Replies View RelatedPicked up a pair of RV220W's for a project I'm working on. I have several IP's available, 4 of which are assigned to/in use by a server behind the RV220W. All 4 of these IP's are static external IPs. How I can configure the RV220W so that requests to those 4 IP's get routed to the server.
Prior to purchasing this, I was under the impression what I was trying to do was called one-to-one NAT, but after reading the 'Help' document on the one-to-one NAT page, I don't think this is right. Emphasis added below: Cisco RV220W Wireless-N Network Security Firewall Help FirewallOne-to-One NATOne-to-one NAT is a way to make systems behind a firewall and configured with private IP addresses appear to have public IP addresses.One-to-One-NAT Rule TableThis table lists the list of available One-To-One NAT rules configured by the user. Private Range Begin: start ip address in private (LAN) ip addressPublic Range Begin: start ip address in the public ip address (WAN IP), Public IP Subnet Mask: The Subnet Mask of the public IPRange Length: Range length maps one to one private address to public address up to the given range.Service: This column shows service to be accepted by LAN Host.The actions that can be taken on One-to-One-NAT rules are:(Check Box At First Column Header): Selects all the entries in the table.Add: Opens the One-To-One NAT Configuration page, to add a new entry. Edit: Opens the One-To-One NAT Configuration page, to edit the selected entry.Delete: Deletes the selected entries.
So according to their documentation, the server in question would need to be configured with a private IP. Unfortunately, one of the applications I use is licensed via IP address and my understanding is that I cannot use the software with private/non-routable IP addresses.
Is the RV220W capable of not only securing the line (firewall, access rules, content filtering, port trigering & forwarding etc) but also doing what I was hoping to do (keeping the external IP's on the server, and routing appropriately)?
I'm using a RV220W router, and recently got shifted to a dynamic IP solution.Now, I've got a no-ip.org address, but the update service seems to be on no-ip.com. So, I try to enter mydomain.no-ip.org OR mydomain.no-ip.com in the dynamic dns settings, under Host and Domain Name, but when saving the settings it says
'The hostname specified does not exist in this user account' ,which seems to indicate that it manages to login to the update service but gets a negative reply.Is it possible to use the RV220W with no-ip.org/com?
We have 2 sites connected thru 2 RV220W routers via VPN and most things are working fine. I have noticed however, that any device that has a web interface, i.e. our Sharp Copier and our Freenas server, is inaccessible. The page tries to come up but then I get the Cisco "server is down" page generated by the RV220W.
I can pull up the web interface pages if I use a machine on the local LAN but not on any machine across the VPN. The only commonality I can think of is the RV220W blocking that traffic for some reason..
Cisco support write down manual (workaround), how to setup IPsec VPN connection on Mac OS 1.7?
View 5 Replies View RelatedIs there anyway to associate a name to an IP in the RV220W? I am coming from a WRVS4400N v2. Folks are complaining that they can't connect, for example via Real VNC, via the PC name any longer. They have to use the IP address. In the past I put the names of the PCs in the WRVS4400N when I reserved IPs via MAC addresses (some call this assigning static IPs). There isn't any place in the RV220W to put the name. Even when I look at the DHCP list a lot of them show up as "unknown". I am sure this is a NETBIOS thing but I'd rather fix this in the router as I have always done in the past.
View 4 Replies View Relatedi have a RV220W and absolutely nothings functional on this stupid Router, no NAT , no Port Forwarding and I cant access my Network from Outside. Any firmware link for downloading. This address works, its handling special webrequest.
View 1 Replies View RelatedI set up a PPTP VPN with an RV220W recently. It was working flawlessly until a recent power outage and now users are getting the 807 error when attempting to connect. I have PPTP passthrough enabled and TCP/UDP 1723 open. As far as I can tell GRE 47 is open as well. Why it was working and is not working after a power outage?
View 2 Replies View RelatedHaving a strange problem that just started this week and got worse this evening. I have a RV220W that is feeding my network. The RV220W sits behind a broadband modem and acts as the DHCP for the network and those computers access the internet that way. Anyway, tonight started an issue where the the RV220W just disappears. Becomes unpingable. I recycle power, and within anywhere from 5 to 10 minutes, it's gone. No longer pingable. Even if I plug a latop directly into it.If I power cycle the RV220W it comes back and I can ping it and access it and its settings. 5 to 10 mins later, I again lose it. Nothing was done. Its been working fine for a few weeks. Had a similar outage last Tuesday, but a recycle of everything brought everything back into line. After I lose connection to it, the lights I expect to be lit remain lit.
View 1 Replies View Related