Cisco Routers :: WRVS440N Did Not Collect Logs
Apr 14, 2013
I have turned on 'Local log' and 'output blocking event log' on my WRVS4400N v2 with latest fw.When I am clicking 'view log' button I can't see anything in empty fields. When I am trying to change logs genre I have empty fields all time.
View 1 Replies
ADVERTISEMENT
Feb 17, 2013
I have found log from IPS on router WRVS4400N and most of attacks i am getting from 0.0.0.0 IP adress. Is it normal?
View 1 Replies
View Related
Jul 20, 2011
I have seen posts and screen shots of WRVS4400N settings screens showing WDS but I can't find anywhere in my setup to enable WDS on my version 1. I am running firmware 1.1.13. This makes me think WDS is only supported on v2 of the WRVS4400N, is that correct?
View 1 Replies
View Related
Dec 4, 2012
i am trying to expand the wifi range of my WRVS4400n. Since the WAP4400 is'nt available i got me a wap321, since it was mentioned as recommende replacement. However i am having trouble in getting the bridge to work.First i tried to use WDS but this only killed my WRVS4400n and i am now trying the Workghroup Bridge mode on the WAP321.
On WRVS4400n i have enabled WDS and have tried both auto setting and Manual without any difference I am stuck with this status on the WAP321:
Network Interface Status and Statistics VLAN ID Name (SSID)
WLAN0UPSTRM Disconnected 1 myssid
WLAN0DWSTRM Up 1 myssid
It is the Infrastructure Client Interface setting that fails, i've tried both None and WPA pesronal Security setting with same result: Disconnected
View 6 Replies
View Related
Jul 16, 2012
I have hardware version 2 and firmware 3.0.2.01 (latest firmware available for this hardware version I believe) and I cannot get it to email me logs. I have entered my outlook address and our SMTP server.The log says that it's failing each time it attempts. I have scoured the internet and I cannot find a solution that will work for me. I have found some talk of adjusting an MTU setting which is supposed to be located under the firewall / general tab.
View 1 Replies
View Related
Aug 29, 2011
I am trying to setup logging on my router. I want to use my gmail account / gmail SMTP server to send emails.
Does the router support TLS for SMTP?
Oh - and I also get the "critical error" page. I get it when I try to un-check the send logs checkbox in the remote logging management page.
View 5 Replies
View Related
Jan 31, 2012
On a RV220W (1.0.3.5) I keep seeing the following error in the logs multiple times:
[Kernel][KERNEL] ERROR:endChantRecv: protocol PNAC returned !OK
What this error is all about and how to fix it?
View 6 Replies
View Related
Aug 19, 2011
Looking at the logs RV220W I can read the following lines:
[rv220w]Fri Aug 19 18:28:54 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378400
[rv220w]Fri Aug 19 18:30:39 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378200
[rv220w]Fri Aug 19 19:23:04 2011(UTC) [rv220w][Kernel][KERNEL] Clearing the ISR a800000003378e00
[ code] ....
What are they?? and what should be done ????.
View 2 Replies
View Related
Sep 3, 2012
I have in my work RV016 10/100 16-Port VPN Router, working Ok and connected with 3 ADSL internet lines.
1- The problem is that when any line disconnect from internet it supposed to log this disconnection in internet in system log but it does not
2- I can't understand the option of sending mail with the logs, does it send when i press the button EMAIL LOG NOW, or it supposed to send when any log is added? and how to configure it.
View 0 Replies
View Related
Mar 25, 2013
I updated my RV180W to the latest firmware and found that port forwarding works I started using it.I've just noticed that since changing over to the RV180W, my Apacher server logs show the router's IP address instead of the remote IP address - every remote request appears to come from 192.168.0.1.
How do I get it to forward the remote IP.
View 1 Replies
View Related
Apr 20, 2013
I have RV042 V01 and V03 and RV082 V03.I'm wondering if there's a difference between the default actions taken by the "Logs" interfaces?
In the case of the V01 systems, it appears that I get a Security Notification every hour.In the case of the V03 system, it appears that I rarely get a Security Notification.
View 1 Replies
View Related
Dec 27, 2011
I am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 Replies
View Related
Aug 29, 2011
if i flash my firmware on my router, can i still view the router logs before the flash? i heard that .logs can be on the ram of the router.
View 1 Replies
View Related
Nov 11, 2011
There are 3 newly installed Cat4506-E.SSH and SNMPv3 access are verificated. Devices are managable in every way only the inventory is missing.If I try to collect manually then they fail but I can't figure it out why.
View 2 Replies
View Related
Mar 22, 2012
I'm using LMS 4.0.1 and VPN hw client 3002 with software 4.7.2.L.I'm not able to collect the first configuration and sync jobs end with these errors.
View 2 Replies
View Related
May 9, 2012
We have just installed lms 4.2 and are having problems collecting config and inventory from ws-svc-wism2-k9. The response from TAC was that this is not supported. And it also says this in
[URL]
Is this really the case ? Will there be released packeges to support this. It would be really useful if this was supported in lms4.2.
View 3 Replies
View Related
Jul 28, 2011
I'm using cisco LMS 4.0, I've discovered the device and next plan is to collect the device configuration.I would like to know, How I can collect the configuration for single device.What configuration changes required on my LMS & Cisco device.
View 1 Replies
View Related
Mar 25, 2012
How can I collect the data about the traffic on my Cisco 2960S? Have I use only the snmp? Any workaround for simulate a netflow? The IOS c2960s-universalk9-mz.150-1.SE2.bin.
View 2 Replies
View Related
Sep 20, 2011
i have an issue for collect data on adapter 1, that don´t collect data but see that adapter 2 if collect data on module 4.
monitor session 1 source vlan 102 rx
monitor session 1 destination analysis-module 4 data-port 1
monitor session 2 source vlan 106 rx
monitor session 2 destination analysis-module 4 data-port 2
I reconfigured newly monitor and continues with that issue. Always ok by data-port 2.
- show version Cisco 6513
Cisco IOS Software, s72033_rp Software (s72033_rp-ADVENTERPRISEK9_WAN-M), Version 12.2(33)SXH7, RELEASE SOFTWARE (fc3)
. show version NAM
NAM application image version: 3.5(1b)
- sh module
Ports Card Type Model
----- -------------------------------------- ------------------
8 Network Analysis Module WS-SVC-NAM-2
Hw Fw Sw Status
------ ------------ ------------ -------
2.0 7.2(1) 3.5(1b) Ok
View 3 Replies
View Related
Dec 22, 2012
how to turn off this logs??
*Mar 2 13:26:07.919: %SEC-6-IPACCESSLOGP: list 101 denied udp 79.2.199.68(57143) -> x.x.x.x (34803), 1 packet
Router#
*Mar 2 13:26:09.766: %SEC-6-IPACCESSLOGP: list 101 denied tcp 108.15.116.235(63864) -> x.x.x.x (34803), 1 packet
Router#
*Mar 2 13:26:11.276: %SEC-6-IPACCESSLOGP: list 101 denied udp 24.130.2.212(26935) -> x.x.x.x (34803), 1 packet
View 3 Replies
View Related
May 24, 2012
I cannot read ACS 5.3 logs from my WCS. I have the ACS server added to the WCS. Below is the message I'm getting:
Unable to connect to any ACS View Server.Failed to access the WSDL at: { URL}. It failed with: {URL}. Do I need to install any special module on the ACS to support this?
View 1 Replies
View Related
Jun 16, 2011
I have a question about VPN Concentrator FTP Backup configuration to get logs on FTP server. I have configure FTP Backup with all details but I still do not see any logs on FTP server. Do you know what could be the issue? I have never used Concentrator and not sure what needs to be done to get in working condition. I am using VPN Concentrator 3015 series.
View 5 Replies
View Related
Nov 4, 2012
I am running two ASA 5520 routers synched up with eachother. I had a massive connectivity issue this weekend that I am investigating. Now I have figured out how to get the live logging but I need to know how to get the old logs from my router.
View 4 Replies
View Related
Sep 6, 2011
I have 3 ACS servers placed throughout N. America. I it set up so that ACS01 is primary and ACS02 and ACS03 are secondary. When i look at the logs for passed/failed authentications in radius or tacacs I cannot see anything from ACS03 logging. This is weird because just a few weeks ago it worked perfectly. In fact, ACS03 is the most active server since this site is using it for wireless phones and tacacs and the other 2 are just using ACS for wireless networking. I went through the log settings and every server is set up the same as the others (except the primary) so it should be logging ACS03 the exact same as 01 and 02.Anyway it seems like a small problem but i need the logs to work correctly to properly administrate security.
View 1 Replies
View Related
Aug 31, 2011
There was a interface down in one of critical devices in the network.that particular log is not captured by the ciscoworks(DFM-alerts).
View 1 Replies
View Related
Jan 1, 2013
My iphone started resetting the connection every 2 minutes today. I noticed that the date maximum is Dec 31, 2012. My logs are getting messed up, and NTP isn't setting. Is there a firmware update for REV E3?? I'm at 5.10 right now.
View 11 Replies
View Related
Oct 16, 2012
I want to secure our WLAN via Web Authentication with our new Cisco 2504 WLC. But where do i find user activity logs?
View 2 Replies
View Related
May 10, 2012
We recently had to rebuild our ACS server. Now when we have an 802.1x authentication failure and look at the RADIUS logs for the specific user, it does not show us the MAC address of the device the user tried to login with. We use this all the time because users have PDAs and other mobile devices that they save their passwords on. Then when they change their domain password on their laptop, they don't change it on their PDA which then tries to authenticate them using the wrong password and eventually locks them out. We need to see the MAC address so we can pinpoint which device is causing the lockout. The report I am generating is when you go to this location: Monitoring & Reports > ... > Reports > Catalog > User > User_Authentication_Summary
View 4 Replies
View Related
Nov 15, 2012
I am using a 2851 router in mpls network. We had a power shut down activity recently and post to that i could not find any logs in the router.
View 4 Replies
View Related
Dec 3, 2012
I have a 5508 wireless lan controller we have two SSID configured Profile Name : Corporate and Guest When I go look at the Most Recent Traps all I see is Client with Mac address blah has joined your corporate, this goes on for sometime. But I am unable to see any of the Guest logs joining the network, I have since then grabbed my laptop and connected to the guest log. I still dont see any logs in Most Recent Traps for the Guest SSID WLAN configuration, I then blocked my Mac address and tried to connect again, No logs. I need to also montior the guest network is there some special tick box I need to apply for this to work? Once the guest is connected I can view them in the clients list but it never shows them on MOST RECENT TRAPS but I want to see the guests account connecting or failing to connect as we currently have a rogue device annoying me.
View 3 Replies
View Related
Jan 6, 2013
what is the meaning of the following log messages on Cisco 7604 Core routers. The Core router is configured with 2 STM card configurations with Vlan assignments: [code]
View 3 Replies
View Related
Oct 13, 2012
We are using almost 10 Nexus 5k in our DC currently we are getting same error logs in all Nexus 5k." ntpd[4746]: ntp:time reset +0.279670 s " ,Is it major error or just for reset time?
View 1 Replies
View Related
Nov 28, 2011
I am receiving trace back logs in the 881G with 3G module. And after reload, the router is going to Initial Config. mode. What the latest IOS is?
Current IOS I am using is c880data-universalk9-mz.151-1.T3.bin. Any better IOS for complete efficient use of the PCEX-HSPA-G Module ?
View 5 Replies
View Related