I am receiving trace back logs in the 881G with 3G module. And after reload, the router is going to Initial Config. mode. What the latest IOS is?
Current IOS I am using is c880data-universalk9-mz.151-1.T3.bin. Any better IOS for complete efficient use of the PCEX-HSPA-G Module ?
i was looking to trace back a website from 2 months ago but not sure how to get into the history of the laptop,
View 1 Replies View RelatedI just purchased the AP1141N and I have created a logon account to access the device via URL which works fine but after 10 minutes it logs me out and requires that I log back on. Unfortunately it won't allow me to log back on unless I reset the device then I have another 10 minutes before it asks me to login again but then it won't accept my logon again without a reset.
I can logon with my account via the console logon but I don't know how to configure the access point via command line so I use the web interface. I have disabled the timing for security but didn't work.
I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies View RelatedI have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies View RelatedI have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies View RelatedI would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?
View 7 Replies View RelatedI have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?
View 2 Replies View RelatedJust to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.
View 1 Replies View RelatedI'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 7 Replies View Relatedsecuring a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).
I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
Which RJ11 pairs will be connected each other [code]
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.
I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.
I am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?
We have both DSL and 3G connection to the 881G and both are up and running.There is a NAT for easy vpn device (10.10.10.2) on this router and currently pointing to DSL interface IP (206.206.206.9) ********ip nat inside source static 10.10.10.2 206.206.206.9 extendable*********
My current requirement is that NAT for easy vpn device should work on 3G if DSL link down.So how we can achive the NAT redundancy. Even when I removed the above NAT and pointing to Cellular0, I am not seeing any translations.
quick question regarding a 3G access via a cisco 881G i have a partner sim card (with the same number as the one in my mobile) iserted into the router.now i have the problem that my mobile is unreachable (line busy), is there a way to use both sims at the same time?what do i have to change in the router configuration?
View 1 Replies View RelatedI try to make working a 881G router with integrated 3G router (cellular 0) with Bouygues or Orange, but I don't found any working configuration
View 2 Replies View RelatedII have a 881g conecting fine with 3G via cel 0, I Can not ping fx 8.8.8.8 or 4.2.2.2 from cli, bur from Lan everyting World fine.
View 19 Replies View RelatedHave customer that we need 3G at new location. Their company is an AT&T customer.So we have got from distribution a 881G and it has a PCEX-3G-HSPA-US card with it.What do you do or need to get AT&T service on this card. You call AT&T they don't know what your talking about if you say Cisco 3G card?I don't see a SIM slot which most AT&T device have a SIM card?Is there somewhere special you have to call for these to get service? Any checklist for ordering and also configuring for AT&T?FYI, we will do DHCP with it and it will be our backup ISP on and ASA if the primary internet goes down. We will just use a 172.30.x.x addressing between the ASA Outside-Backup interface and the 881G.
View 1 Replies View RelatedI've been asked to configure an 881 with a Verizon 3G backup connection as a backup to the FE4 primary WAN connection. I've been unable to get any connectivity through 3G, and in most cases, as soon as I try to configure 3G, I lose connectivity through FE4.Currently, I don't even have FE4 connected. I'm just trying to get the 3G connection working, so then I can take it back to the office and have a functional 3G backup connection. [code]
View 1 Replies View Relatedtoday I received a Cisco Router 881G with PCEX-3G-HSPA-G for a customer that ordered a Router with the feature to send/receive SMS and to remotely active the 3G Internet connection through SMS. I believe that the router that meets this requirement is the Router 881G that I received today. In particular, the model is:
CISCO881G-K9
Now, I installed the router and configured the 3G link that is working properly BUT all the commands related to the SMS are completely missing. In particular, I miss the command:
cellular gsm sms send
gsm sms archive path
In the following documentation I see that these commands should be available: [URL]The fact that these commands are missing sounds very strange to me since the documentation is pretty clear. Do I need to activate any license? I also upgraded tha router to the last version...
Here it is the show version of the Router:
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sat 24-Mar-12 00:00 by prod_rel_team
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
[code]....
i have a 881G and an IP SLA icmp configured. (ip sla 1). I can get the status of it by the OID:
1.3.6.1.4.1.9.9.42.1.2.10.1.1.1
But, on the same router i have a track 1 for the SLA 1 and a track 2 monitoring track 1 with threshold . What i want, is to get the OID of track 2 so i can get the status of it. Which OID is that?
an external Antenna for a 881G? We're using AT&T.
View 4 Replies View RelatedBelow is the config has done on my 881g but the dual NAT failover is not working.I have a easy vpn over NAT (easy vpn firewall: 10.10.10.2 behind the router).
1. After completed the config, I shut down the FastEthernet4, cleared the nat translations, found that nat translations are happening on to Cellular0 with error ( Incomplete ESP translations: 0 esp_conn=0x85A91FF0, hanging off nat entry 0x85A7D1D0)But still the easy vpn is not up as I am not able to ping the remote devices.
2. If I reboot the router then the nat translations are happening with no above error and easy vpn is up and I am able to ping the remote servers. Below is the config, what needs to be done to achieve the NAT failover and easy VPN up.
interface FastEthernet4 bandwidth 2048 ip address 206.206.206.2 255.255.255.240 ip flow ingress ip nat outside ip virtual-reassembly duplex auto speed auto interface Cellular0 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer in-band dialer string gsm dialer-group 1 async mode interactive ppp chap hostname. [code]
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
View 4 Replies View RelatedI have an issue regarding using cellular interface on cisco 881G. The 3G module is Aircard 504. SIMcard is working on other devices, it have obtain IP address from mobile operator. But on cisco881G it doesnt work.
Here is config:
cellular 0 gsm profile create 1 m2m
chat-script 3G "" "ATDT*98*4#" TIMEOUT 30 CONNECT
interface Cellular0
[Code].....
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp
Cellular0: Only SLIP encapsulation supported
Router(config-if)#
[Code].....
I've been already purchased current cisco device (881g-k9),my vendor told me that there is possible to actrivate adipservices license on this router (i need encryption).i'm waiting now for license from my vendor .but for now i tried to activate trial adv_IP lic and got no success on it.So question is there possible to activate AdvancedIpServices license on this router?
View 3 Replies View RelatedCan Cisco 881G cellular interface (Modem Firmware Version = K2_0_7_19AP C:/WS/FW) work with r-uim cards? I can't find correct answer in documentation .
View 2 Replies View RelatedI would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200
ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4
ip address dhcp
no shut
duplex auto
speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1
ip address 10.73.0.1 255.255.255.0
ip helper-address 192.168.140.13
ip tcp adjust-mss 1400
no autostate
ip sla 100
icmp-echo 10.64.4.15 source-interface Vlan1
tag 3G Keepalive
frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
I have Cisco 881g with 3g.I can;'t find any documentation about sending USSD requests from 3g module.is it possible to send USSD request ?
View 0 Replies View Related