Wireless :: Trace Back A Website From 2 Months Ago
Mar 8, 2011i was looking to trace back a website from 2 months ago but not sure how to get into the history of the laptop,
View 1 Replies
ADVERTISEMENT
Cisco WAN :: 881G - Trace Back Logs
Nov 28, 2011I am receiving trace back logs in the 881G with 3G module. And after reload, the router is going to Initial Config. mode. What the latest IOS is?
Current IOS I am using is c880data-universalk9-mz.151-1.T3.bin. Any better IOS for complete efficient use of the PCEX-HSPA-G Module ?
Linksys Wireless Router :: E2000 Not Powering On After 5 Months
Jul 10, 2011i went to bed last night and my router was working fine, but today when i woke up my E2000 had no power it was still plugged in, do you think i fried it? i have only had it sence march and this has never happened before.
View 1 Replies View RelatedLinksys Wireless Router :: E4200 Quit Working After 5 Months
Jul 24, 2011I have been using the E4200 router with few issues for the past 5 months. I have the latest firmware installed and have 1 pc running Windows 7, a sling box device and USB storage drive connected in the rear and 7 wireless devices.
Over the past week, others in my household have been complaining of not being able to connect wireless. The other day, the connection quit for both wireless and wired connections. I thought it had something to do with my ISP (Comcast), and after I made a direct connect from my modem to my PC, the problem is the E4200. After unsuccessfully troubleshooting, I unplugged the router for a few hours.
Trying a few hours later, I was able to reconnect all connections. However, that lasted for a day and has not been able to connect. I did a reset and when going through the setup process, it says that it cannot connect to the internet. The only time I have any lights or activity on the internet port is when the router is booting up and then it goes off. The rest of the ports are working properly. Likewise, the link light on my modem shows no activity when connected to the E4200. The only connection I can make is to the browser utility.
I am now using another wireless router until I can get this resolved.
Internet Has Been Unstable For 3-4 Months
Aug 26, 2012About 3 and a half months ago my internet connection has been extremely unstable. It will be fine for 20-30 minutes and then will spike up to anywhere from 4000 to 6000 latency and give me a constant disconnect for 2-7 minutes. This connection is affecting every computer in the house as well as the playstation 3 that is connected by wi-fi. All the computers in my house are hardwired.
View 2 Replies View RelatedCisco Switching/Routing :: ATM 8510 Back To Back With 7206vxr 155Meg Only Get 44Meg?
Nov 25, 2012I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-
kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled: AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712 <====
I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-
atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?
Cisco Switching/Routing :: Connecting Two 2951 Back To Back Through A HWIC-4T1 Card
Dec 4, 2011What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?
View 1 Replies View RelatedCisco Switching/Routing :: HWIC-4SHDSL-E Router Back To Back Connection?
Apr 11, 2013I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?
View 1 Replies View RelatedCisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?
Nov 25, 2011I have 2650XM router and 2620 Router Both routers have built in WIC T1 CSU/DSU cards
2620Router --
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
Hardware is PQUICC with Fractional T1 CSU/DSU
Description: DTE side
MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
reliability 255/255, txload 1/255, rxload 1/255
Encapsulation HDLC, loopback not set
[code]....
My question is that cisco website says there are two type of cable connections for this type of config --which are --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable it did not work.So for this type of connection i know i need T1 cross over cable-- which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over -- will this cable work in my router to router connection.
Cisco Switching/Routing :: 2611 / 2801 - Configuration For Back To Back Support
Oct 19, 2012I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .
View 1 Replies View RelatedCisco Switching/Routing :: 7204 Locks Up After Every 6 Months
Nov 28, 2007I can't seem to find out what this means. Every 6 months or so, my 7204 locks up. I can't even get to it via the console port and I must reboot to access it. I noticed this alarm in my logs.( ASSERT CRITICAL PO1/0 Threshold Cross Alarm - B3) I've looked on-line but can't pinpoint it's meaning. Looks like a flapping interface but might be something else.
View 6 Replies View RelatedCisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?
Jan 8, 2013I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire. Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?
View 7 Replies View RelatedCisco WAN :: HWIC-4SHDSL-E Router Back To Back Connection
Apr 14, 2013I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?
View 2 Replies View RelatedMotorola SB6121 Recurring Loss Of Cable Signal Every Day For Five Months
Aug 18, 2012My Motorola SB6121 DOCSIS 3 modem is connected to a Medialink n-band router. Sometime in the morning (usually between 7am and 9am, the router loses the ability to see the modem. I can access the router's control panel, and I see 0.0.0.0 for WAN IP, Subnet Mask, and Gateway. Primary and Secondary DNS server are both blank. Connection Mode is Dynamic IP.I lose the ability to access the modem's control panel directly (192.168.100.1), even though the PC I use is hardwired to the router. So, I unplug the modem, unplug the router, wait, plug in the modem, plug in the router, and everything works again.I've had more than twelve service calls. Every Charter tech looks at the line, puts in boosters, takes out boosters, replaces splitters, and seems to only look at signal. I've BEGGED Charter to let me speak to an engineer, because my suspicion is that it's something to do with the DHCP server.
I did, by the way, replace EVERYTHING.I have had 5 different modems...same problem. I have had 5 different routers...same problem, including a modem/router combo.I've tried different brands, too.I've disconnected all wifi devices from the router, and rebuilt my PC's operating system. I've even unplugged the refrigerator, because one Charter tech claimed it was "upstream noise."I've been online only a few times when the system actually goes down. What I notice in the router logs is this: [code] So at 9:34, no ranging response - T3 timeout, followed by Unicast Ranging Received Abort Response;
then the Cable Modem Reboot due to T4 timeout, and the system time goes to 1/1/1970 at midnight. No ToD.
The last piece of information: Charter installed a second modem as a "test." That was originally in the same room. A month ago they did another line from the box directly to the test modem to skip the splitter on the house.That modem shows the same problems, EXCEPT -- not perfectly in sync. I might see the same error, but the time will be a few minutes and seconds off. And sometimes I'll see the errors, but the modem won't go down.Sometimes the first modem goes down, sometimes the second. I'm accustomed to a router "healing" itself when the modem goes down.It might be off for a bit, but then will re-establish. This Medialink doesn't do that. It forces a physical restart every day. There are other outages too, and all I get from Charter is "the signal strength is good."
Cisco Switches :: Sx300 Series Requires Reboot Every 2 Months
Nov 15, 2011We have 3 sf-300 series switches in Layer3 mode deployed in different offices. We have found that approximately every 2-3 months at all 3 locations users experience a serious reduction in bandwidth. Only after rebooting the cisco does the problem go away and we're okay for another few months. some setting/feature that may be contributing to this? We are only using several ports and 1 static route on each switch. We are not using any of the bells and whistles on the switch. 2 of the switches are using the original firmware, whereas the other is using the newest firmware. Maybe this is just what we should expect from a Small Business switch?
View 18 Replies View RelatedCisco WAN :: E1 Clocking Back To Back 3925 Routers
Feb 29, 2012Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.
View 1 Replies View RelatedCisco Routers :: Connecting Two RV082 Back To Back
Jan 7, 2013I'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop. Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart. There will be no internet connection.
View 7 Replies View RelatedCisco WAN :: 1841 Securing E1 Back-to-back Connections
Aug 28, 2012securing a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).
Cisco WAN :: Connecting Two 878 G.SHDSL Routers Back To Back
Apr 7, 2013I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
Which RJ11 pairs will be connected each other [code]
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.
Cisco WAN :: 888 SHDSL Routers Back To Back
Dec 15, 2011I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.
Linksys Wireless Router :: E4200 Won't Update / Ping Or Trace Route
Jan 21, 2013I have an E4200 and have added it to my network with a new static IP and DHCP and firewalls off.It runs off my cable modem and router (Virgin Media Superhub) that has DHCP.When I tell it to do a firmware update, traceroute or ping it fails, just wont do any of them.
View 9 Replies View RelatedCisco WAN :: 2901 Back To Back BRI Using WIC-1B-S/T-V3
May 26, 2013I am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?
How To Trace Ip Address During Chat
Apr 30, 2011how to trace ip adress during chat
View 2 Replies View RelatedServers :: Trace IP When Proxy Is Used?
Jun 17, 2011how to trace IP when proxy is used.someone I know is playing a prank that might cause my marriage to break.That person uses proxy with many different IP and also a loopback. does anyone know how to trace the IP even with the above is used.
View 2 Replies View RelatedTrace A Device Using Ip Address?
Jun 24, 2012Is there any way to trace a device using Ip address?
View 2 Replies View RelatedReverse Trace Route?
Dec 29, 2011I want to know the return path between my IP and a server. I know that trace route gets some information about the hops from my IP to a server (for example www.google.com) but this info is about the forward path. But I want to know what is the path from the server to my PC, what is the reverse path (return path)? What are the middle hops? In other word, I want to know where is the forward and reverse path when I ping a server? I can find the forward path using trace route, but what about the return path?
View 7 Replies View RelatedHow To Trace A Lost Laptop
Mar 31, 2012track my laptop
View 2 Replies View RelatedCisco :: TCP Trace-route On A Certain Port?
May 7, 2012I am trying to track down a device that's blocking a certain port I know there are programs out there than will do a trace-route that's on TCP but is there any programs that allow you to specify a port?
View 6 Replies View RelatedHow To Trace A Stolen Computer Mac Address
Jun 13, 2011If my computer was stolen could I locate it using the unique mac address? And is this why burgular didn't take two laptops when they burguled us last night
View 1 Replies View RelatedTrace Port Used By Exchange Server?
Mar 3, 2012We use microsoft exchange for outlook. I want to know which ports are being used by our exchange server to receive and send emails. Is it possible to check that?
View 1 Replies View RelatedHow To Trace Lost Toshiba Laptop
Jun 23, 2012i think someone took my laptop i can not know unless i can track it i have all the info on the laptop i still hae the box but i desperatly need to know where, basically someone has it and is telling me it is mine but will not let me see it.
View 1 Replies View RelatedHow To Trace Missing Toshiba Laptop
Dec 14, 2012our laptop missing at banaganapalli kurnool dist andhra pradesh
View 1 Replies View RelatedHow To Trace The Load Balancers In Data Center
Feb 22, 2012How to trace firewall and load balancers placed in data center.
View 6 Replies View Related