Cisco WAN :: 2901 Back To Back BRI Using WIC-1B-S/T-V3

May 26, 2013

I am setting up my lab using two 2901 routers which is running on 15.2 IOS.I am trying to simulate a back to back BRI.BRI Module: WIC-1B-S/T-V3 (x2) one of each router.
 
I followed this amazing document to understand the concept of BRI and configuration. url..but it never says if i can use the module that i have mentioned.
 
Q1. What cabling i need to use to setup back to back BRI using 2x 2901 routers with these modules?
Q2. What cabling do i need to use.
Q3. Is it actually possible to use these 2 modules alone to simulate a back to back BRI..?

View 6 Replies


ADVERTISEMENT

Cisco Switching/Routing :: ATM 8510 Back To Back With 7206vxr 155Meg Only Get 44Meg?

Nov 25, 2012

I have a Cisco 8510msr that is connected back to back with a 7206vxr across a 155Meg connection.I receive lots of Output drops on the 7206vxr interface facing the atm switch. When I do the following command:-

kwdair9#sh atm int atm 1/0Interface ATM1/0:AAL enabled:  AAL5 , Maximum VCs: 4096, Current VCCs: 27 Maximum Transmit Channels: 0Max. Datagram Size: 4528PLIM Type: SONET - 155000Kbps, TX clocking: LINECell-payload scrambling: ONsts-stream scrambling: ON797522 input, 881483 output, 203946630 IN fast, 223768062 OUT fast, 0 out dropVBR-NRT : 110288 Avail bw = 44712   <====  

I only have 44megConfig. is ACTIVEkwdair9# I only get 44Meg of the available 155Meg.There is no QOS on the router and the only commands I can find that vaguely see that refer to QOS are on the ATM switch:-

atm address 47.0091.8100.0000.0007.0d87.b201.0007.0d87.b201.00atm router pnnino aesa embedded-number left-justifiednode 1 level 56 lowest  redistribute atm-static?why this is acting like a DS3 link and not a 155Meg link?

View 4 Replies View Related

Cisco Switching/Routing :: Connecting Two 2951 Back To Back Through A HWIC-4T1 Card

Dec 4, 2011

What cable I need to connect two 2951 back to back through a HWIC-4T1/E1 card ?

View 1 Replies View Related

Cisco Switching/Routing :: HWIC-4SHDSL-E Router Back To Back Connection?

Apr 11, 2013

I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?

View 1 Replies View Related

Cisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?

Nov 25, 2011

I have 2650XM  router and 2620 Router Both routers have built in WIC  T1 CSU/DSU cards
 
2620Router --
 
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
  Hardware is PQUICC with Fractional T1 CSU/DSU
  Description: DTE  side
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, loopback not set

[code]....
 
My question is that cisco website says there are two type of cable connections for this type of config --which are  --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable  it did not work.So for this type of connection i know i need T1 cross over cable--  which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over  --  will this cable work in my router to router connection.

View 5 Replies View Related

Cisco Switching/Routing :: 2611 / 2801 - Configuration For Back To Back Support

Oct 19, 2012

I have 1 2611xm router and 1 2801 router. For my own lab purpose, i want to configure them back to back to support voice services. I don't know what configuration will be required at each end. in 2611xm, i have NM-2V and its also detecting the card, so i hope it will work ? also what commands i need to run on both ends .

View 1 Replies View Related

Cisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?

Jan 8, 2013

I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire.  Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?

View 7 Replies View Related

Cisco WAN :: HWIC-4SHDSL-E Router Back To Back Connection

Apr 14, 2013

I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?

View 2 Replies View Related

Cisco WAN :: Need Data License To Switch Back To 3g 1941 And 2901 ISR Routers

Oct 2, 2012

I have 1941, 2901 ISR routers. I will use 3G backup when primary link (metro ethernet / G.SHDSL) goes down. Do I have to use Data License (SL-19-DATA-K9 / SL-29-DATA-K9) in order to switch back to 3G when primary link is not reachable) ?

View 7 Replies View Related

Cisco WAN :: E1 Clocking Back To Back 3925 Routers

Feb 29, 2012

Just to get this clear as having issues with a E1 link with CRC's at one.Router A,Network-Clock-Participate WIC 1,Should router B have clock participate for WIC 1? We currently have controllers set as UNFRAMED but guess we can set to NO-CRC4 both ends and telco will pass this.

View 1 Replies View Related

Cisco Routers :: Connecting Two RV082 Back To Back

Jan 7, 2013

I'm looking for instructions on how to setup and connect two RV082 routers together with a crossover cable between their WAN ports. This is to connect two separate LANS together via an ethernet connection. For staging we are setting everything up with a crossover cable in our shop.  Ultimately the crossover cable will be replaced by a microwave link between the two LANS several miles apart.  There will be no internet connection.

View 7 Replies View Related

Cisco WAN :: 1841 Securing E1 Back-to-back Connections

Aug 28, 2012

securing a back-toback connection using E1.The connection is between two cities, using 2x CISCO 1841 router + VWIC-1MFT-E1 interface at each city.
 
The E1 connections has been provided by our local telco, and they are completely private. The customer is a bank, and they asking me if this is a secure connection or not. If possible, we need to guarantee that no body can get access to the bank network even if they brought E1 modem at one of the ends (telco PoP).

View 11 Replies View Related

Cisco WAN :: Connecting Two 878 G.SHDSL Routers Back To Back

Apr 7, 2013

I searched a lot but couldnt find a clear document about connecting 2 G.SHDSL routers back to back.First of all I am not sure which type of cable (RJ11) is used for connecting two 878 routers. Does it have to be cross or straight cable.
 
Which RJ11 pairs will be connected each other [code]
 
According the configuration samples One router must be CPE and the other must be CO for simulating DSLAM.

View 2 Replies View Related

Cisco WAN :: 888 SHDSL Routers Back To Back

Dec 15, 2011

I'm having some trouble getting two Cisco 888's to work correctly back to back.. The two routers will ultimately be used in conjunction with a BT EPS8 circuit which is effectively four wires short distance between customer sites. We have configured lots of these using the older Cisco 878's.
 
Anyway, as i've been struggling to get line sync on site I've gone back to basics and connected the two 888's back to back. However, I've found that no matter what I do I can only get the routers to sync at 384kbps!? And that's with a one meter RJ11-RJ11 cable.. Very strange. When we've used the 878's we get much more bandwidth. I have tried statically assigning the line rate at both ends but it still only works at 384kbps.

View 3 Replies View Related

How To Get Back On Old Network

May 11, 2011

I have a desk top not wireless i have a laptop wirelesss i have a linksy wireless router i jumped or seomething happen to my desk top i have no promlems getting on line. My desk top used to be on network abc and now it says it is hooked up to network 2 and all these messages keep coming up with my firewall i tried to get back on abc network and can't i have to play around to get on network 2 to get on line.

View 6 Replies View Related

How To Get Scrabble Back

Mar 15, 2012

How to get Scrabble back.

View 1 Replies View Related

Cisco :: Get A PAK Back From A License?

Dec 19, 2012

Is it possible to get a PAK back from a license? For example, if the PAK is joined with the wrong serial number is there a way to revert the binding of the PAK and serial to get just the PAK again?

View 5 Replies View Related

Why Don't Get Back An ACK Segment From Client

Jun 15, 2012

I am currently working on a project which purpose is to establish a TCP connection between a PC and a microcontroler.I configured (in C language) the µC as the server, and the PC as the client (in C#, using the TCPClient class).While running the codes, I capture the frames on the network with Wireshark.The client's ISN is chosen randomly by the TCPClient.Connect method.Since there will be only one TCP connection at a time, the server's ISN is always 0.The server's port is 0xC0C0 (49344) and the client's port is also chosen randomly by the TCPClient.Connect method.find the screenshot of the Wireshark's capture attached.In compliance with RFC793, the three-way-handshake should conclude with an ACK segment from the client.In my exemple, the client tries to connect three times, and then drops : the client sends no ACK segment.The µC's SYN-ACK reply may be bad configured .What kind of information did I miss ? Are there special data the client is expecting ? Why don't I get back an ACK segment from the client?

View 3 Replies View Related

Deleted Emails Get Them Back?

Jun 10, 2011

Can I retrieve emails that were deleted in error.

View 1 Replies View Related

Get Printer Back Online?

Feb 1, 2013

How do I get printer back online?

View 1 Replies View Related

D-Link DIR-825 :: Go Back To The Old Version?

Feb 9, 2011

I need USA style log. I have a DIR-825 B1 with Firmware Version: 2.05WW. How can I setup (; go back) to the USA 2.05NA version? The firmware upgrade was failed cause that the uploaded firmware file may not be correct..

View 8 Replies View Related

Cisco :: How To Back Up IOS To TFPT Server

Aug 26, 2012

I am trying to create a backup of my 2620 router so I can use for GNS3. I have only configured the IP address on my FastEthernet port. Having many issues with no connection to my pc, finally I found that you must enable the interface 'no shutdown'. Now I have a valid connection

View 7 Replies View Related

Cisco WAN :: 887 Back-up Interface Routing

Jun 20, 2010

I have configured 887 Router. ADSL with 3g(backup) everything is fine but the routing seems not working.interface ATM0 backup delay 120 60 backup interface Cellular0 no ip address no atm ilmi-keepalive dsl bitswap both [code] Tha nat is working but the routing seems not working. When I run remove "ip route 0.0.0.0 0.0.0.0 Dialer0" command I can connect internet. but it did not work. When I disconnect adsl line and run sh route, I see dialer 0 is the default route for 0.0.0.0.  I need to configure backup route for 0.0.0.0 network

View 12 Replies View Related

Cisco WAN :: WRVS4400N Routing To URL Back Onto Itself

Nov 9, 2011

I have an iPad that uses an app to control the house. I create a dyndns url to maintain connection to the house from the outside world. When I bring the iPad onto the internal network, the url routing fails. Externally, it works fine. I think it's some sort of protection that is configured within the router.
 
Proper configuration to allow the URL to kind of loop back onto itself, when it's in the house? Where, in the configuration, this is set to prevent this kind of routing?

View 1 Replies View Related

Cisco :: WLC Fail-Back With 1140 APs

Mar 18, 2013

We've recently sold and implemented a wireless solution using a WLC, WCS and 1140 APs.
 
There is a HQ site where the WLC, WCS, DNS and DHCP reside. Active Directory and a RADIUS server are also located there. There is then a WAN link to remote sites which sometimes fails. At the remote sites you'll just have a router, switches and the APs. The intention is for the APs to work in lightweight mode, falling back to H-REAP when the WAN link fails.That works fine, but what doesn't work fine is the APs rejoining once the WAN link is restored.
 
They just don't. Even days later, the APs are still all disassociated from the controller despite the WAN link being up. I've 'hardcoded' the controller IP into the AP configuration, while the APs initally get the IP for the WLC from DHCP using Option 43. Despite the APs therefore knowing where WLC is, once they're disassociated from it (WAN link failed) they will not reassociate by themselves. Restarting the APs is the only way to get them to rejoin.
 
With hundreds of APs and in excess of 30 switches, restarting all the APs each time the WAN link fails is pretty ridiculous.
 
I've logged a TAC case and gone through the whole rigmarole, this is an offical bug and Cisco have informed us that it's due to be fixed sometime early 2011, but besides that there is nothing they can do. So to be perfectly clear, Cisco have sold and shipped a product that doesn't work as advertised and they best they can offer us is a promise to fix it soon. I'm pretty shocked, I've never had this experience with Cisco in the past.
 
Ok, so now I've got to come up with a decent workaround until we get a firmware release where this is fixed. I'm looking at using CNA to automate the reloading of all the switches, I guess when an outage is reported I'll just write a procedure for the client to follow to reload all their APs.
 
A script that can query the associated status of APs and reload them as needed, automatically, would be pretty cool. Perhaps that can be done with SNMP.

View 1 Replies View Related

Broadband :: Get Original Homepage Back?

Feb 21, 2013

They changed my homepage & I really don't like it! Want my original page back! This just happened today...2/21/13

View 1 Replies View Related

How To Get Home Screen Back To Yahoo

Feb 9, 2011

I installed google toolbar for taskbar but I want yahoo for my homepage

View 1 Replies View Related

Broadband :: 2 Internet Connections One As Back Up?

Mar 24, 2011

I have a primary internet connection which is broadband and the secondary connection as a Reliance data card in my laptop. I have noticed that which ever connection,connects the last, becomes the primary connection and if the primary ever goes out, the second connection takes over and gives me continuous connectivity.Is it possible to configure and specify which connection I want to be primary regardless of which connection connects last etc?

View 1 Replies View Related

Wireless :: How To Get Email Back To IPad

May 18, 2011

My mail will not open, says pass word is incorrect, how do I get this to change? I have wi-fi, and I deleted a bunch of old e-mails off of pc. Since I have done this, I can not get anymore mail sent to my iPad. Can you direct me to how to change this?

View 1 Replies View Related

How Can A Public Ip Be Traced Back To Private Ip

Mar 1, 2012

How can a public ip be traced back to private ip. for instance if the ip is 5.5.5.5 it is traced as

4.4.4.4
2.2.2.2
1.1.1.1
10.10.10.10
5.5.5.5

I thought it could be VPN but then u still need a public facing ip , or can it be the fact that the public ip is router to nat and from nat to internet but then 10 range will need to be converted back to public which does not happen as from the private 10.10.10.10 it moves to the next router which is an isp device and not clients one?

View 1 Replies View Related

Network Computer Does Not Reply Back

Jan 10, 2013

I have a problem in my Computers network. We have more than hundered computers in our network. When I ping from my computer to other computers that are on the same switch. Does not show any problem. But when I ping to the computers that are on the switched which are not directly connected to the same switch but are on the other swtiches. Ping replys some times and some times it gives request timeoue.

View 1 Replies View Related

SF310 - Can't Back Up It To A Network Drive

Feb 16, 2011

I want to back up my samsung 310 to a network drive and seem unable to do so using Samsung backup and with windows 7 home you cannot back up to a network drive. It is a home network.

View 1 Replies View Related

Why Can't Change Taskbar Back To Preview

Jan 16, 2013

To enable the taskbar preview I have been told to open taskbar properties and I would find what to click to enable taskbar preview when I hover the mouse over icon.I have tried and cannot find the answer. During chat session w/ McAfee, CSR could not do it either.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved