today I received a Cisco Router 881G with PCEX-3G-HSPA-G for a customer that ordered a Router with the feature to send/receive SMS and to remotely active the 3G Internet connection through SMS. I believe that the router that meets this requirement is the Router 881G that I received today. In particular, the model is:
CISCO881G-K9
Now, I installed the router and configured the 3G link that is working properly BUT all the commands related to the SMS are completely missing. In particular, I miss the command:
cellular gsm sms send
gsm sms archive path
In the following documentation I see that these commands should be available: [URL]The fact that these commands are missing sounds very strange to me since the documentation is pretty clear. Do I need to activate any license? I also upgraded tha router to the last version...
Here it is the show version of the Router:
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
Copyright (c) 1986-2012 by Cisco Systems, Inc.
Compiled Sat 24-Mar-12 00:00 by prod_rel_team
ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
I've got two routers, Cisco 2911's with 15.1(4)M1 on one and 15.0(1)M5 on another.
I'm trying to set up ip sla for vrrp tracking but the commands seem gimped? I don't even have an option for ip sla <operation number>. All I've got is ip sla responder/server/key-chain.
I am using DHCP/TFTP to autoconfigure a 3945 router. The router properly obtains an IP address and finds the correct TFTP server. The issue lies in the download of the configuration file from the TFTP server. The router downloads the file, gives the "Ok" message, and prompts you to press Return to get started. When I view the running-config, several commands are missing from the Serial 0/0/0 section (HWIC-2T). If I modify the config file on the TFTP server to use Serial 0/0/1 instead and repeat the process, the configuration file loads without any issues and Serial 0/0/1 has all of the commands.
I also tried moving syntax around in my config file, but the end result is still the same. If I use Serial0/0/0 - I don't get all of the commands. If I use Serial 0/0/1, I do.
We have both DSL and 3G connection to the 881G and both are up and running.There is a NAT for easy vpn device (10.10.10.2) on this router and currently pointing to DSL interface IP (206.206.206.9) ********ip nat inside source static 10.10.10.2 206.206.206.9 extendable*********
My current requirement is that NAT for easy vpn device should work on 3G if DSL link down.So how we can achive the NAT redundancy. Even when I removed the above NAT and pointing to Cellular0, I am not seeing any translations.
quick question regarding a 3G access via a cisco 881G i have a partner sim card (with the same number as the one in my mobile) iserted into the router.now i have the problem that my mobile is unreachable (line busy), is there a way to use both sims at the same time?what do i have to change in the router configuration?
Have customer that we need 3G at new location. Their company is an AT&T customer.So we have got from distribution a 881G and it has a PCEX-3G-HSPA-US card with it.What do you do or need to get AT&T service on this card. You call AT&T they don't know what your talking about if you say Cisco 3G card?I don't see a SIM slot which most AT&T device have a SIM card?Is there somewhere special you have to call for these to get service? Any checklist for ordering and also configuring for AT&T?FYI, we will do DHCP with it and it will be our backup ISP on and ASA if the primary internet goes down. We will just use a 172.30.x.x addressing between the ASA Outside-Backup interface and the 881G.
I've been asked to configure an 881 with a Verizon 3G backup connection as a backup to the FE4 primary WAN connection. I've been unable to get any connectivity through 3G, and in most cases, as soon as I try to configure 3G, I lose connectivity through FE4.Currently, I don't even have FE4 connected. I'm just trying to get the 3G connection working, so then I can take it back to the office and have a functional 3G backup connection. [code]
i have a 881G and an IP SLA icmp configured. (ip sla 1). I can get the status of it by the OID:
1.3.6.1.4.1.9.9.42.1.2.10.1.1.1
But, on the same router i have a track 1 for the SLA 1 and a track 2 monitoring track 1 with threshold . What i want, is to get the OID of track 2 so i can get the status of it. Which OID is that?
Below is the config has done on my 881g but the dual NAT failover is not working.I have a easy vpn over NAT (easy vpn firewall: 10.10.10.2 behind the router).
1. After completed the config, I shut down the FastEthernet4, cleared the nat translations, found that nat translations are happening on to Cellular0 with error ( Incomplete ESP translations: 0 esp_conn=0x85A91FF0, hanging off nat entry 0x85A7D1D0)But still the easy vpn is not up as I am not able to ping the remote devices.
2. If I reboot the router then the nat translations are happening with no above error and easy vpn is up and I am able to ping the remote servers. Below is the config, what needs to be done to achieve the NAT failover and easy VPN up.
interface FastEthernet4 bandwidth 2048 ip address 206.206.206.2 255.255.255.240 ip flow ingress ip nat outside ip virtual-reassembly duplex auto speed auto interface Cellular0 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer in-band dialer string gsm dialer-group 1 async mode interactive ppp chap hostname. [code]
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
I have an issue regarding using cellular interface on cisco 881G. The 3G module is Aircard 504. SIMcard is working on other devices, it have obtain IP address from mobile operator. But on cisco881G it doesnt work.
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp Cellular0: Only SLIP encapsulation supported Router(config-if)#
I've been already purchased current cisco device (881g-k9),my vendor told me that there is possible to actrivate adipservices license on this router (i need encryption).i'm waiting now for license from my vendor .but for now i tried to activate trial adv_IP lic and got no success on it.So question is there possible to activate AdvancedIpServices license on this router?
Can Cisco 881G cellular interface (Modem Firmware Version = K2_0_7_19AP C:/WS/FW) work with r-uim cards? I can't find correct answer in documentation .
I would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200 ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4 ip address dhcp no shut duplex auto speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1 ip address 10.73.0.1 255.255.255.0 ip helper-address 192.168.140.13 ip tcp adjust-mss 1400 no autostate ip sla 100 icmp-echo 10.64.4.15 source-interface Vlan1 tag 3G Keepalive frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
I've been trying to configured Websense urlfiltering using ZFW feature on my Cisco 881G router. The router is running on IOS 15.0(1)M with Advanced IP Services. And I have confirmed it supports urlfilter feature.
This is what I tried to accomplish but IOS version 15.0x seems to have different command set. ----------------------- class-map type inspect httptraffic match protocol http parameter-map type urlfilter param server vendor websense 10.20.30.40 [Code]...
In studying and testing SSL VPN on an ASA I have the network as shown in the attached diagram. The configuration is based on an ASA with 8.3 but our ASA is 8.2 and at this time I'm not familiar with the new NAT configuration and commands in 8.3 or later and how to translate the 'nat (inside,outside) source static' for me to an 8.2 version.
I try to get a ASA with the new software 8.4.2 running. On an old pix we had the nat command: static (inside,outside) tcp interface www 192.168.15.252 www netmask 255.255.255.255 0 0,In all the new documents about 8.4.2 I can find that it should work with something like:
I want to forward http traffic from the outside interface to this host. In the log I just get entries about blocking ACL - but both is allowed on the outside access-list - traffic to the inside IP and also to the outside interface IP.
I also tried it with "Public Server" - but when I try to use the Interface address I just get the message: Address x.x.x.x overlaps with outside interface address.
Is it still possible to do port forwarding on the outside interface?
I have two nic one connected with DSL modem with gateway 192.168.1.1 for Internet. another nic connected with office Intranet with gateway 10.226.122.x . I can connect only one network at a time disabling other.. I know route add command can be used for linking the both network so I can simultaneously use Internet and Intranet..can you elaborate with example (five years ago I set up the same with route add command.. now my memory failing..)
I have a Cisco 3925 router running IOS 15.2 I am trying to configure IP SLA on it. The configuration is supposed to be what is pasted below. but the CLI is rejecting the commands.Its taking oly the "ip sla responder" command after that if I enter "ip sla 1083180034" command it says invalid input. [code]
I have configured the TACACS in my network and I have configured the aaa authorization commands 15 default if-authenticated group tacacs+ in Cisco 6504 Switch. Its allowing me to Login by Unable to run the Sh run commands ,i am getting Aithorization error emssage. If i am checking sh Privillage its showing level 15. Same configuration fine in other device with out issue.
Are the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
Have a conceptual question bout CLI command authorization. We have ASC 5.2 up and running, providing AAA services for network devices. Now I need to make profiles for users in certain group to restrict dem CLI "rights" to show, clear counters and show running-config commands. I need to accomplish dis task.I should clrete separate privillege levele profile (let it be 2), specify commands at this level, assign Group this Authorization Prifile and make some additional changes in my devices.
I am looking to configure PBR in Nexus. The current setup in IOS is :
interface Vlan10 ip address 172.27.206.1 255.255.255.0 ip address 172.27.208.1 255.255.254.0 secondary ip policy route-map Vlan_10_to_Corp route-map Vlan_10_to_Corp permit 10match ip address Vlan_10_to_Corp set ip next-hop 172.27.209.250!route-map Vlan_305_to_EFH permit 30
[code]....
But, Nexus PBR will not work with deny statements init. Now, what options do I have ?
we've got a pair of old 3745's that are getting upgraded to new 2911's, and I'm trying to run IOS 15.2 on the new routers to get them most current before going into test and production use.The routers are doing BGP, IPv4, and HSRP, and I'm trying to put one in at a time as to not have to big bang everything at once. I'm putting the one that matters least in first, and basically using the same config as the old one, which was running IOS 11.
I was using "no ip mroute-cache" on ethernet interfaces, and it says that command is deprecated and I should use the MFIB commands instead. Darn if I know what that means, I believe it was set up so the ethernet interfaces had IP multicast fast switching disabled, which was set up by our vendor 10 years ago so I'm not sure if it matters. It would seem logical to me this would have an impact on HSRP and speed of failover. Does this matter, and if so how in the world do I do this with IOS 15.2?The second one is the use of "no fair-queue" on our serial connection for a T1. This command isn't there either, and I'm not sure if I even need to bother on this. It was set up on the old router on a T1 Frame Relay circuit.
I have just received 4 static ip's from my isp, i want to be able to point these ip's at different services on my internal servers, for example: [code]. The firewall I have is Cisco PIX 515, how to set the NATing up or commands?
