Have customer that we need 3G at new location. Their company is an AT&T customer.So we have got from distribution a 881G and it has a PCEX-3G-HSPA-US card with it.What do you do or need to get AT&T service on this card. You call AT&T they don't know what your talking about if you say Cisco 3G card?I don't see a SIM slot which most AT&T device have a SIM card?Is there somewhere special you have to call for these to get service? Any checklist for ordering and also configuring for AT&T?FYI, we will do DHCP with it and it will be our backup ISP on and ASA if the primary internet goes down. We will just use a 172.30.x.x addressing between the ASA Outside-Backup interface and the 881G.
I would like to configure the 881G to use both the cellular interface and Fe4 WAN port for internet connectivity.Interface Fe4 is connected to an ADSL router.
I have configure each interface with a default route and weighting:
ip route 0.0.0.0 0.0.0.0 Dialer0 200 ip route 0.0.0.0 0.0.0.0 FastEthernet 4 100
I need to configure Fe4 to get an address as a DHCP client:
interface FastEthernet4 ip address dhcp no shut duplex auto speed auto
How do I remove Fe4 from VLAN1? There is some existing config around VLAN 1:
interface Vlan1 ip address 10.73.0.1 255.255.255.0 ip helper-address 192.168.140.13 ip tcp adjust-mss 1400 no autostate ip sla 100 icmp-echo 10.64.4.15 source-interface Vlan1 tag 3G Keepalive frequency 10
Then I guess I need to adjust my Internet-IN ACL to allow broadcasts and UDP 67 and 68?
I am trying to figure out how to setup quality of service on my network. At the moment i have computers connected to the PC port of my IP phone and the IP phone connected to the switch.I want the PC to stay on the default native VLAN and the phone to go on the VLAN 10I am using SNOM300 and SNOM360. I will configure the on the phone the VLAN ID and the priority.From my research, there are two ways that I can go about this on the port that is connected to the phone I canswitchport voice vlan vlan-idorswitchport voice vlan dot1pand then I will have to execute the commandmls qos trust cosmy question is which command do i use to configure the ports, and am I on the right track? Also, this is how I configure the ports that the IP phones are connected to, how do I configure the port that my Asterisk PBX server is connected to?
I'm trying to configure a dhcp service on a router for some vlans.I would like to give the range 172.16.0.0 - 172.16.10.255 to vlan 10, 172.16.20.0 - 172.16.20.255 to vlan 20.for some reason it doesn't work?here's the config.
ip dhcp excluded-address 172.16.0.1 ip dhcp excluded-address 172.16.20.1 ip dhcp excluded-address 172.16.30.1 ip dhcp pool vlan10 network 172.16.0.0 255.255.0.0
I am trying to confgure a L2L VPN tunnel to a service provider using an ASA 5505.My problem is that the service provider will not accept traffic from a LAN subnet, they will only accept traffice from a public IP.We have a small public subnet of x.x.x.50/255.255.255.248, our public IP (outside interface IP on the ASA 5505) is x.x.x.50 and the service provider wants to see traffic coming from us on x.x.x.51How can I NAT our LAN subnet (10.0.0.0/24) to one public IP (x.x.x.51)?
I have struck in my some network configuration. I have two sf300 switches and cisco 827 router. Actually sf300 does not support dhcp server. I took cisco 827 as dhcp server and i create 4 dhcp pools in it. How i can configure in sf300 to take dhcp service from cisco router 827. Isit possible to configure 827 with bvi interface, when i was try i got below error. how to configure bvi interface and i will link that bvi to vlan on sf300. error in 827 router, How i can connect two sf300 switch for redundancy ? I connected giga4 SW1 and giga4 SW2 and mode trunk isit good or any other way i need to connect it.?
I'm trying to support a friend. They just switched to TWC Business Class from Megapath. They have a Cisco 5505 ASA and are trying to configure it to work with the new TimeWarner cable modem. But we can't get PCs behind the firewall out to the Internet.
We think it should be a pretty simple config. They have the ASA connected directly to the modem. The modem is running DHCP, and we''ve configured the ASA to get its address via DHCP. We have a Windows server behind the firewall; it can't get out the Internet either. It's set up to be a DHCP server and is giving IP addresses to the PCs on the network.
Laptops connected via wifi to a wireless router attached to the modem are able to connect to the internet, thus we know the modem is up and running fine.
I have just changed my ISP and received a Thomson TG712 Modem, router and VoIP Gateway. Nice device, but I would like to extend my wi-fi network and connect a couple of PCs to another router in a different area using an almost new Linksys E4200 as a second router.I have already wired a network cable from the TG712 to the location where the E4200 is, tested the connection using a laptop, but cannot configure the E4200 to work receiving Internet service from the TG712.
I am not able to configure Service policy output command in Cisco 2921 router.While configuring I am getting below error.Same config is working fine in Cisco 3845 router.I am suspectting the problem with license in IOS.
I have a WRT100 wireless router, which is configured for a PPPOE connection to my ISP. After running one of the tools to determine responsiveness of DNS name services, I would like to manually configure my DNS services, placing a more responsive service as my first DNS choice. In the router administration, I can configure three static DNS IP's. However, I don't see any place in the configuration to turn off the automatic DNS configuration from my ISP. So, when I issue an IPCONFIG /ALL on my computer, the DNS listing shows two DNS Name Services from my ISP ahead of the three static DNS IP's that I configured.
Wireless service on Dell laptop computer had been running fine for 4.5 months until underground Comcast cable failed, presumably due to freezing and thawing in cold New England soil. All Comcast service went out, TV, Internet cable modem, etc. Service was restored with above ground cable, and wireless service returned to other devices in household, but not the Dell laptop. I am wondering if my wireless card itself was damaged in the event, as no software fixes I have tried have worked. However, the device manager says the Dell Wireless 1397 WLAN Mini-card is working properly and the driver software for the service is up to date.
Some of the messages I have received from various command line and dialogue box attempted fixes:
Dell Wireless 1515 Adapter Device Not Found
There are currently no wireless adapters available and enabled
Cannot repair adapter because wireless service is not running
Windows could not start the WLAN AutoConfig service on Local Computer
Error 0xc00 ce508 : 0x00 ce508
There might be a problem with one or more network adapters on this computer
>The Wireless Autoconfig Service (WLANSVC) is not running
When I was in administrator mode and ran SFC/SCANNOW the response was this Windows Resource Protection found corrupt files but was unable to fix some of them Details are included in the CBS.Log WindirLogsCBSCBS.Log For example C:WindowsLogsCBSCBS.Log Other command line responses:
Wireless LAN Adapter Wireless Network Connection:
Media State… Media disconnected Tunnel adapter Local Area Connection* 6: Media State… Media disconnected Tunnel adapter Local Area Connection* 7:
[code]....
Other information about the computer:
Inspiron 1545, Dell BIOS version A10, BIOS date 7/17/09, running Microsoft Windows Vista Home Premium, Processor Pentium (R) Dual-Core CPM T4200@2.00 Ghz, Network Card Adapter Marvell Yukon 88E8040 PCI-E Fast Ethernet Controller, Wireless 1515 WLAN Half mini card (Atheros).
We have both DSL and 3G connection to the 881G and both are up and running.There is a NAT for easy vpn device (10.10.10.2) on this router and currently pointing to DSL interface IP (206.206.206.9) ********ip nat inside source static 10.10.10.2 206.206.206.9 extendable*********
My current requirement is that NAT for easy vpn device should work on 3G if DSL link down.So how we can achive the NAT redundancy. Even when I removed the above NAT and pointing to Cellular0, I am not seeing any translations.
quick question regarding a 3G access via a cisco 881G i have a partner sim card (with the same number as the one in my mobile) iserted into the router.now i have the problem that my mobile is unreachable (line busy), is there a way to use both sims at the same time?what do i have to change in the router configuration?
When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
I've been asked to configure an 881 with a Verizon 3G backup connection as a backup to the FE4 primary WAN connection. I've been unable to get any connectivity through 3G, and in most cases, as soon as I try to configure 3G, I lose connectivity through FE4.Currently, I don't even have FE4 connected. I'm just trying to get the 3G connection working, so then I can take it back to the office and have a functional 3G backup connection. [code]
today I received a Cisco Router 881G with PCEX-3G-HSPA-G for a customer that ordered a Router with the feature to send/receive SMS and to remotely active the 3G Internet connection through SMS. I believe that the router that meets this requirement is the Router 881G that I received today. In particular, the model is:
CISCO881G-K9
Now, I installed the router and configured the 3G link that is working properly BUT all the commands related to the SMS are completely missing. In particular, I miss the command:
cellular gsm sms send gsm sms archive path
In the following documentation I see that these commands should be available: [URL]The fact that these commands are missing sounds very strange to me since the documentation is pretty clear. Do I need to activate any license? I also upgraded tha router to the last version...
Here it is the show version of the Router:
Cisco IOS Software, C880 Software (C880DATA-UNIVERSALK9-M), Version 15.2(3)T, RELEASE SOFTWARE (fc1) Technical Support: [URL] Copyright (c) 1986-2012 by Cisco Systems, Inc. Compiled Sat 24-Mar-12 00:00 by prod_rel_team ROM: System Bootstrap, Version 12.4(22r)YB5, RELEASE SOFTWARE (fc1)
i have a 881G and an IP SLA icmp configured. (ip sla 1). I can get the status of it by the OID:
1.3.6.1.4.1.9.9.42.1.2.10.1.1.1
But, on the same router i have a track 1 for the SLA 1 and a track 2 monitoring track 1 with threshold . What i want, is to get the OID of track 2 so i can get the status of it. Which OID is that?
We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.
Below is the config has done on my 881g but the dual NAT failover is not working.I have a easy vpn over NAT (easy vpn firewall: 10.10.10.2 behind the router).
1. After completed the config, I shut down the FastEthernet4, cleared the nat translations, found that nat translations are happening on to Cellular0 with error ( Incomplete ESP translations: 0 esp_conn=0x85A91FF0, hanging off nat entry 0x85A7D1D0)But still the easy vpn is not up as I am not able to ping the remote devices.
2. If I reboot the router then the nat translations are happening with no above error and easy vpn is up and I am able to ping the remote servers. Below is the config, what needs to be done to achieve the NAT failover and easy VPN up.
interface FastEthernet4 bandwidth 2048 ip address 206.206.206.2 255.255.255.240 ip flow ingress ip nat outside ip virtual-reassembly duplex auto speed auto interface Cellular0 ip address negotiated ip nat outside ip virtual-reassembly encapsulation ppp dialer in-band dialer string gsm dialer-group 1 async mode interactive ppp chap hostname. [code]
We deploy 881G routers at our store locations and are planning to upgrade the IOS to 15.2.2. One concern we have is if the router fails to boot to the new image. Is there a way to configure a second boot image as a failover in case the primary boot image does not load? Our current DR plan is to have a laptop on site that we can connect to remotely and setup a console session to manually change the boot file. This can be cumbersome and time consuming, so I'm wondering if the 881 has the ability to have another file loaded if the boot fails.
I have an issue regarding using cellular interface on cisco 881G. The 3G module is Aircard 504. SIMcard is working on other devices, it have obtain IP address from mobile operator. But on cisco881G it doesnt work.
I have a Cisco 881G with PCEX-HSPA-3G card for which I have successfully configured for internet. As the above one has come to end of life, we got the replacement 881G with embedded 3G modem.
I can't get Cellular 0 to use ppp encapsulation:
Router(config-if)#encapsulation ppp Cellular0: Only SLIP encapsulation supported Router(config-if)#
I've been already purchased current cisco device (881g-k9),my vendor told me that there is possible to actrivate adipservices license on this router (i need encryption).i'm waiting now for license from my vendor .but for now i tried to activate trial adv_IP lic and got no success on it.So question is there possible to activate AdvancedIpServices license on this router?
Can Cisco 881G cellular interface (Modem Firmware Version = K2_0_7_19AP C:/WS/FW) work with r-uim cards? I can't find correct answer in documentation .
I have a fresh installation of LMS 4.0 on windows server 2003, when i click to open topology i get error message : ANIServer service may be down or Host name isn't DNS resolvable
i tried pdshow -brief ANIServer ===> service UP
DNS is working using host file in driversetc i restarted the server
I've been trying to configured Websense urlfiltering using ZFW feature on my Cisco 881G router. The router is running on IOS 15.0(1)M with Advanced IP Services. And I have confirmed it supports urlfilter feature.
This is what I tried to accomplish but IOS version 15.0x seems to have different command set. ----------------------- class-map type inspect httptraffic match protocol http parameter-map type urlfilter param server vendor websense 10.20.30.40 [Code]...