Cisco Switching/Routing :: How To Configure Sm-es2-16-p Service Module To Route Over 2911
Jun 17, 2012Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies
ADVERTISEMENT
Cisco WAN :: 2901 / 2911 Routers Service Module?
Dec 5, 2011I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies View RelatedCisco Switching/Routing :: 2911 Can Support Ip Service Image
Feb 29, 2012i want to check if cisco2911-sec/k9 can support IP service image? what PAK(license) can be bought to activate the IP service feature set?
View 1 Replies View RelatedCisco Switching/Routing :: Cat6500 SUP-2T Service Module
Apr 12, 2012Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
Cisco Switching/Routing :: 6500 - VSS And ASA Service Module
Mar 10, 2013we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies View RelatedCisco Switching/Routing :: 2911 - Assign IP To Interface In Module?
Jul 25, 2012I need to configure a Cisco 2911. I need to give an interface in this module (VWIC3 - 4MFT-T1/E1) an IP address. My question is, how to assign an IP to an interface in this module.
My purpose is to get connectivity via T1 line to another router.
Cisco Switching/Routing :: 1941W - Service Module Failed
Jul 25, 2012we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Cisco Switching/Routing :: How Switch Module Works In 2911 Router
Sep 4, 2012 how this switch module works in 2911 router? I have two 2911 routers in HSRP configuration for redundancy with crossover cable between switch modules. OSPF running on routers.If active router loses its power and then comes back again, it boots first, its internal link to switch module comes up and it starts to forward packets to switch module. The switch module starts to boot only after router is ready. So I have outage of about 3-4 minutes. For our real-time applications it is way too long.
any way to start booting of the switch module before router gets ready?I understand I can boot it manually, but it is only after router is ready. Only way to get around it I found is to disable internal link and use router interface to connect to the switch module.
Cisco Switching/Routing :: 6509 VSS Implementation As A Service Module Core
Jun 8, 2011I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies View RelatedCisco Switching/Routing :: SM-ES2-24 - Installation Of Enhanced EtherSwitch Service Module
Dec 12, 2011I have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
Cisco Switching/Routing :: 2921 / How To Quit Service-module Session
Jun 9, 2012On 2921, how do you quite service-module session and get back to the router?
View 3 Replies View RelatedCisco Switching/Routing :: 2851 - Service Module Won't Accept IP Stating
Oct 18, 2012[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
Cisco Switching/Routing :: 2911 Couldn't Access Internet With Route Specified
Dec 19, 2011I couldn't access internet with route specified i know the problem with the route or nat.i have 2911 router [code]
i could ping from lan Ip's to ISP1 and ISP2 gateway IPS. but when i ping to any site llike example gmail.com packet s not moving out to the ISP1 or ISP2 interfaces. [code]
Cisco Switching/Routing :: Unable To Configure VPN On 2911 Router
Jan 29, 2012I have a Cisco 2911 router that I will like to use it for setting up a site to site VPN but the router does not support VPN commands. When I issue crypto isakmp command, it says command no recognized. When I issue ipsec transform-set command, it says command not recognized. The IOS running on my router is c2900-universalk9-mz.SPA.151-2.T1.bin. Also see the output of my show licences features command: [code]
what can be done on this router to enable use it for setting up a VPN connection.
Cisco Switching/Routing :: 2900 - How To Configure Module NM-16ESW
Apr 1, 2013How to configure a module NM-16ESW because with the command "show diag" and "show int" can not query it.
Note: the default IOS is installed, you will need to upgrade to a specific '.
Cisco Switching/Routing :: How To Configure Route Between Two Subnets On 2960-S
Jun 21, 2012configuring a working route between two subnets (172.28.0.0/16 and 192.168.0.0/24) on a Cisco Catalyst 2960-S.
Problem: The subnet 172.28.0.0/16 is on VLAN 40 and the clients on this subnet have to access a preconfigured device with an ip in 192.168.0.0/24 subnet. The configuration of this device cannot be changed.
I have an Cisco 2960-S Lan Base (c2960s-universalk9-tar.150-1.SE3) switch [URL] that I would like to use to solve this problem.
Cisco Switching/Routing :: 5510 How To Configure A Backup Route To Internet
Jul 24, 2012how to configure a backup route to the internet. My client has 2 ISP and basically they want to use 1 ISP and in case the ISP fails, use the other one as backup route to the internet.
The problem I’m facing is that each ISP is plugged to a dedicated ASA 5510, so 1 ISP in one firewall and 1 in the other. Both ASA are plugged to an internal network in a dedicated VLAN with a L3 switch and that L3 switch manages the internal network.
My question is, how can I tell my switch to use ASA1 to go out to the internet and in case the ASA 1 OR THE LINK TO INTERNET used by ASA 1 fails, use ASA 2? It would be great if I can send traffic to the internet thru both connections at the same time. Also, I know the ASA has High Availability configuration, but that applies only if both licenses in the devices are the same and I have a mismatch with the SVPN license, and also I don't know if with my current topology I can use the High Availability model, so I think I can’t use that option and the solution must be applied in the L3 switch, but I don’t know how to tell it to use ASA1 and if failure of the device or the outside interface plugged to ISP 1, then use ASA2. Besides, I would like to know how to optimize this config to do the switch between internet connections seamless to the users if possible (there are VoIP calls on this floor, so I don't want to drop the calls).
Protocols / Routing :: Cisco 2911 Configure Incoming Connections
Dec 19, 2011We have a Cisco 2911 Router and have configured via BT Infinity Broadband for out going internet access etc. Are there any incoming restrictions ACL settings etc. that will stop us using for ISA VPN, Exchange connections, Intranet, Sharepoint etc. We have reserved 13 Static IP Addresses from the ISP.
View 1 Replies View RelatedCisco WAN :: Cannot Enable Embedded-Service-Engine On 2911
Dec 1, 2012i cann't enable embedded-Service-Engine on cisco2911 router.
View 3 Replies View RelatedCisco :: Wrong IOS On A Switch Service Module?
Mar 11, 2013I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies View RelatedCisco WAN :: Service Ready Engine 910 Module
Jan 1, 2013can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View RelatedCisco WAN :: 2911 Dual ISP Route?
Jun 18, 2012We have a cisco 2911 cisco router so i want to use as a load balancer using two different ISP networks, example if the first ISP network gets down i need the second ISP will take over all routing and get for internet access
here is my scenerio..
First ISP = PUblic ip = 155.1555.155.2 gateway = 155.155.155.1
seceond ISP Public = 40.51.16.9 gateway = 40.51.16.1
Inside network = 192.168.1.0. /24
Cisco WAN :: Service Module Installation In 3845 Router?
Jun 3, 2013Is there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies View RelatedCisco Firewall :: Upgrade ASA Service Module On Cat 6504?
Mar 20, 2013I just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver
Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
Cisco :: 2911 IP Route MIB Not Supported In IOS Version 15.0
Dec 14, 2011We've recently started using some 2911's on our network running IOS 15.0(1r)M9. I noticed, much to my frustration that the OIDs with the MIB RFC1213: ip RouteTable1.3.6.1.2.1.4.21 are not supported.
Any alternative MIB for viewing routing table information via SNMP on any of these devices running a similar IOS?
Cisco WAN :: 2911 - Switch Module With POE Doesn't Give Any Power Out
Nov 7, 2011We got a new Cisco 2911 router (CISCO2911/K9) with a switch module (SM ES2-16-P) on it. Everything works fine after the configuration except for the power. We got 4 WAP that we will connect to the switch module that needs power. So the switch module with POE doesn't give any power out.
[code]....
Cisco Wireless :: 2811 Service Module Is Trying To Recover From Error
Mar 27, 2012I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies View RelatedCisco Application :: Password Recovery For ACE Service Module 6500
Dec 27, 2011I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies View RelatedCisco Application :: Does ACE Service Module Support SHA2(256) Certificates
Sep 1, 2010Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies View RelatedCisco Application :: ACE30-MOD-K9 Module Crash Due To Service Cfgmgr
Dec 2, 2012My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
Cisco WAN :: 2911 Have Aggregate 1.6 Gbps Towards Route Processor
Aug 11, 2011The Cisco 2911's have aggregate 1.6 Gbps towards route processor - I am trying the same specs for Cisco 3845 router? from url...The EHWIC slot provides enhancements to the prior generation's high-speed WAN interface card (HWIC) slots while provide maximum investment protection by natively supporting HWICs, WAN interface cards (WICs), voice interface cards (VICs), and voice/WAN interface cards (VWICs).
• Four integrated EHWIC slots on the Cisco 2901, 2911, 2921, and 2951 allow for more flexible configurations.
• Each HWIC slot offers high-data-throughput capability
• Up to 1.6 Gbps aggregate toward the route processor
• Up to 2 Gbps aggregate to other module slots over the MGF
Cisco WAN :: 2911 - Support Interface ADSL Module Like Backup Link?
Apr 27, 2011i will going to buy a router 2911 but i want know if support a interface ADSL modulo like backup in case that my primary link WAN Ethernet down and up the adsl link with a module HWIC ADSL pots.
View 1 Replies View RelatedCisco WAN :: 7301 - Route Reflector Maintenance Without Service Interruption
May 27, 2013I have question regarding route reflector. In my MPLS core network ,we have two route reflectors. Two route reflectors and each PE routers are belonged to a peer group. Route reflectors are Cisco 7301. IOS 12.3. I have Hardware maintenace on one Routereflector. How can I do that without interupting the end customer trafic.
View 2 Replies View Related