Cisco Switching/Routing :: SM-ES2-24 - Installation Of Enhanced EtherSwitch Service Module
Dec 12, 2011I have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
ADVERTISEMENT
Cisco Switching/Routing :: Configuring EtherSwitch Module On A C2911 ISR G2?
Jun 12, 2013We just received a new C2911 G2 ISR and have been trying to configure the EtherSwitch SM-ES2-24-P module on it. Through the router console, I tried assigning an IP address to the router Gi1/1 interface which I assume is the link to the Etherswitch module but all I'm getting is "IP addresses may not be configured on L2 links" - as per the docs, I should be able to assign an IP address on that "logical" interface link. Any other way for me to configure the ports on that switch module?
View 5 Replies View RelatedCisco WAN :: Service Module Installation In 3845 Router?
Jun 3, 2013Is there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies View RelatedCisco Switching/Routing :: Cat6500 SUP-2T Service Module
Apr 12, 2012Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
Cisco Switching/Routing :: 6500 - VSS And ASA Service Module
Mar 10, 2013we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies View RelatedCisco Switching/Routing :: 1941W - Service Module Failed
Jul 25, 2012we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
Cisco Switching/Routing :: How To Configure Sm-es2-16-p Service Module To Route Over 2911
Jun 17, 2012Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies View RelatedCisco Switching/Routing :: 6509 VSS Implementation As A Service Module Core
Jun 8, 2011I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies View RelatedCisco Switching/Routing :: 2921 / How To Quit Service-module Session
Jun 9, 2012On 2921, how do you quite service-module session and get back to the router?
View 3 Replies View RelatedCisco Switching/Routing :: 2851 - Service Module Won't Accept IP Stating
Oct 18, 2012[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
Cisco WAN :: 2921 Router With Etherswitch Module Baud Rate Unsetting
Feb 14, 2013I have a 2921 router with 1 etherswitch module installed. I haven't done it before and was trying to change the baud rate to 115200 for installing an IOS on the etherswitch module which had been deleted. I ended up "unsetting" the baud rate on the etherswitch and rebooted. Now, when I try to session into the etherswitch, its opens the connection but I can no longer see any text on the screen. Im using Teraterm. I've tried different baud rate settings for my serial port in TeraTerm but still cant see any text on the screen. I dont know of any commands from the router prompt. Any suggestions to fix this? If can start seeing the text, then I can probably configure and set up the etherswitch module.
View 1 Replies View RelatedCisco Switching/Routing :: How To Configure 2921 With EtherSwitch
Jun 10, 2012configuring up a 2921 router for remote site which is fitted with 24 port Etherswitch module.As part of this setup I have defined 3 vlans on the router, but when I go onto etherswitch and for example set switchport access to access vlan 3 it is not aware of this vlan.Do I have to set up trunk inbetween Router and its etherswitch?Wish I had ordered seperate switch as it would have been easier or am I missing something.sho vlan-switch shows my vlans but on swicth sho vlan brief does not.
View 10 Replies View RelatedCisco WAN :: Enhanced FlexWAN Module Compatibility With 7603-S (RSP720-10GE)
Dec 25, 2012Is Enhanced FlexWAN module compatible with 7603-S with RSP720-10GE?We have a PA-POS-2OC3 on a 7200 router and we want to use it on 7603-S.
View 1 Replies View RelatedCisco Switching/Routing :: Is Cat3560X Support A Enhanced PAgP
Jan 13, 2012I think that a catalyst3560X connect to VSS Catalyst 6509 by ether-channel.
I'd like to connect a catalyst3560X to VSS Catalyst6509 by the Ether-channel.
I heard need "Enhanced PAgP" that VSS Catalyst6509 connect to by Ether-Channel.
I don't know supported "Enhanced PAgP" on Catalyst3560X.
Cisco Switching/Routing :: 6509 VSS Active-Dual Detection Via Enhanced PAgP
Oct 15, 2012I have the Cisco VSS consisting two chassis 6509.I have the system Active-Dual detection via Enhanced PAgP with one neighbor - standalone cisco 3750. All works good.I want to add one more neighbor - cisco stack 3750x with 3 members. Will this scheme work? And what is in danger, if the stack is split into two parts?
View 2 Replies View RelatedCisco Switching/Routing :: 8700W Enhanced AC Power Supply With 6513 Chassis
Mar 6, 2013I understand that 8700W enhanced AC power supply is Compatible with 6-, 9-, and 13- slot chassis
Based on 8700W Enhanced PS datasheet, it can be installed into existing Cisco Catalyst 6500 Series Switch chassis: both E- and non-E series Cisco Catalyst 6500 Series Switch chassis.
Can we use 8700W enhanced AC power supply with 6513 externally / internally (within one of the chassis slots like 6513-E ?
Cisco Firewall :: SSM-4GE Module Installation On Active And Standby Firewalls
Jul 23, 2011We are planning to install a new SSM-4GE module on both Active and Standby firewalls. how can we install an new SSM-4GE with a minimum outage. I was planning to install the module in the following steps.
1. Power off the secondary firewall(FW02).
2. Install a new module.
3. Power up the secondary firewall
4. Power off the primary firewall(FW01)---> in this step will the secondat firewall become active as there is a hardware conflict.
5. Install a new module.
6. Power up the Primary firewall(FW01)
or do i need to power down both the firewalls and then install the modules?i have is that after the installation only one port on the new SSM-4GE module would be in use on Primary firewall(FW01) which is a terminating link from a router. No link would be terminating on the new SSM-4GE module on secondary firewall. Will the firewalls still fail over in this case or does it require a link going to the secondary firewall on new SSM-4GE module(same port as on primary firewall) from the router.
Cisco :: Wrong IOS On A Switch Service Module?
Mar 11, 2013I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies View RelatedCisco WAN :: Service Ready Engine 910 Module
Jan 1, 2013can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies View RelatedCisco WAN :: 2901 / 2911 Routers Service Module?
Dec 5, 2011I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies View RelatedCisco Firewall :: Upgrade ASA Service Module On Cat 6504?
Mar 20, 2013I just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver
Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
Protocols / Routing :: Belkin Enhanced Wireless Modem Router?
Oct 5, 2011I bought this ( Belkin N150 Wireless Modem Router with Push Button Security Set Up and Network Status Display (F6D4630uk4A): Amazon.co.uk: Computers & Accessories )I want to use this instead of the modem I have now. Is it possible to make this my modem to connect to from the internet? I have a cheap talktalk modem and I want to get rid of it.
View 2 Replies View RelatedCisco Wireless :: 2811 Service Module Is Trying To Recover From Error
Mar 27, 2012I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies View RelatedCisco Application :: Password Recovery For ACE Service Module 6500
Dec 27, 2011I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies View RelatedCisco Application :: Does ACE Service Module Support SHA2(256) Certificates
Sep 1, 2010Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies View RelatedCisco Application :: ACE30-MOD-K9 Module Crash Due To Service Cfgmgr
Dec 2, 2012My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
Cisco Infrastructure :: 3550 Versus 3650 For Enhanced Image In Terms Of Routing
Apr 9, 2006How does the 3550 with enhanced image compare to the 3650 with enhanced image in terms of routing functionality?
View 5 Replies View RelatedCisco Firewall :: Catalyst 6509E / Migrating From FWSM To ASA Service Module (ASASM)?
Jun 6, 2013I'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
View 1 Replies View RelatedCisco Switching/Routing :: Installation Time Of NPE 7200 Series With NPE-G2
Feb 1, 2012What is the installation time for the Network Processor engine is:
NPE-G2=7200 series NPE-G2 engine with 3 GE/FE/E ports ,Do you reckon it can be done in two hours?
Cisco Switching/Routing :: 3560 ISO Image Installation XY Mode
Apr 24, 2013I have L3 switch 3560 v2 cisco switch. If i connect the switch via the console cable in XP system i am not getting any responce. I think i need to install via XY mode.
how can i install the ISO iamge via XY mode in cisco switch 3560 v2.Cisco Model: WS-C3560v2-48tS-S.
Cisco Switching/Routing :: 800 - Wireless In A Rack Mount Installation
Jan 10, 2013I have a question if your Cisco 800 series wireless in a rack mount installation in racks to place the signal strength materials very well ?
View 0 Replies View RelatedCisco Switching/Routing :: IOS Installation For Switch 2960G 48TC-L?
Oct 23, 2012i had made a software upgarde on the switch 2960G series have no any passwords, when I fished the upgrade process after rebooting the device i found it need a UserPw to access device manager. i tried to use the default PW "cisco" but it dosen't work too.. after that i tried the password recovery process to rest the PW, but noway, but now i have addition problem, when i try the cmd orders "flash_init , load_helper , dir flash" to beginning the password recovery process it shows the following:
The system has been interrupted prior to initializing theflash filesystem. The following commands will initializethe flash filesystem, and finish loading the operatingsystem software:
flash_init boot
switch: flash_initInitializing Flash...flashfs[0]: 554 files, 19 directoriesflashfs[0]: 0 orphaned files, 0 orphaned directoriesflashfs[0]: Total bytes: 32514048flashfs[0]: Bytes used: 15540224flashfs[0]: Bytes available: 16973824flashfs[0]: flashfs fsck took 10 seconds....done Initializing Flash.
switch: load_helperUnknown cmd: load_helper
switch: load_helperUnknown cmd: load_helper
switch: load_helperUnknown cmd: load_helper
[code]....
After that the problem updated
because I tried to install the IOS by Xmodem to reload the missing flash file.After finsh the TAR file loading and reboot the switch.......the LEDs of mode and Giga ports are lighted amber and not blinking, i tried many times to follow the steps to connect the switch by the emulator and consol cable by holding mode button and connecting the power cable at same time the device does not work, the switch now still not blinking, now i try to read and understand how can i remove the corrupted files and install a new IOS for this switch?What shall i do.
Cisco Switching/Routing :: 3900 - Add On Module
Jun 10, 2013i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies View Related