Cisco Switching/Routing :: 6500 - VSS And ASA Service Module
Mar 10, 2013
we are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies
ADVERTISEMENT
Dec 27, 2011
I have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies
View Related
Apr 12, 2012
Using the new SUP-2T, need to clarify one query. If we are using the new SUP-2T in VSS mode, will the new ASA service module and NAM-3 are supported? From Cisco site, ASA module FAQ:
Q. Will the ASA Services Module support the Cisco Catalyst Virtual Switching System (VSS) at FCS?
A. Yes, depending on which supervisor you use. The ASA Services Module supports VSS either as a single firewall or as a failover pair of firewalls, when used with the Supervisor 720-10G (VS-S720-10G-3C and VS-S720-10G-3CXL). Transparent and multi- context modes also work with the VSS in this configuration. However, though the SUP 720-3B (WS-SUP720-3B and WS-SUP720-3BXL) is supported by the ASA Services Module, it is not capable of supporting the VSS. No reference to Supervisor-2T.
View 2 Replies
View Related
Jul 25, 2012
we have approx. 70 Cisco 1941W routers deployed in our company. I used to be able to console into the internet wireless AP by issuing the below command:
service-module wlan-ap0 session
However lately this hasn't been working and AP just simply refuses connection. Here is what I have for Status. I have tried reseting the Service Module to no avail.
Router#service-module wlan-ap0 status
Service Module is Cisco wlan-ap0
Service Module supports session via TTY line 67
Service Module is failed
Service Module reset on error is disabled
Service Module heartbeat-reset is enabled
Service Module is in fail open
Service Module status is not available
View 3 Replies
View Related
Jun 17, 2012
Any example of how to configure an sm-es2-16-p service module to route over an Cisco 2911?
View 2 Replies
View Related
Jun 8, 2011
I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies
View Related
Dec 12, 2011
I have a 2911 ISR and want to install a SM-ES2-24 Enhanced EtherSwitch Service Module.
Do I need to power down the router?
View 4 Replies
View Related
Jun 9, 2012
On 2921, how do you quite service-module session and get back to the router?
View 3 Replies
View Related
Oct 18, 2012
[code]....
I can access the ACNS with this config. The issue is that it will not cache anything when I enable WCCP on both ends. I am unable to set the gateway to the IP (even when static) to the WAN interface IP with the error Network Unreachable by content engine. If I address it within the 192.168.2.X network and gateway to 2.1, it locks up when cache is enabled. 192.168.0.5 (the external wan int) is unreachable as a gateway.
I've tried the unnumbered ip on the internal interface but then the service module won't accept an IP stating that the router side must have an IP set.
I had WCCP attempting to cache but timing out on everything without caching a thing. I want/need to understand the IP routing before I get ahead of myself.
View 1 Replies
View Related
Aug 16, 2012
when I do a show module in my cat 6509, the standby sup is saying unknown, it has the same IOS as the primary card.
what does this mean? are there any tests I can run on the card?
View 2 Replies
View Related
Feb 12, 2012
Cisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer inspection of the Switch Sys log, I observed the following Sys log error messages: [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.
View 2 Replies
View Related
Aug 20, 2012
I have a 6500 switch and i recently removed a module (line card) from the switch. The problem is that the port configurations of the removed module still exhists in running configuration. I was not aware of the right procedure,[URL] however, i would like to know whether it resolves if i reboot the switch.
View 1 Replies
View Related
Dec 21, 2011
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies
View Related
Mar 11, 2013
I am having issues (nothing new there) I have a bad IOS on a switch module, and the config is set to boot to that IOS, and as such I get a nasty boot loop, I am trying to figure out how to get into rommon but all the documentation I can find for this just says go into rommon and never tells me how to get there on a switch module that thinks it has a good IOS. (The IOS is for our normal service module but this one is an odd-ball switch)
View 4 Replies
View Related
Jan 1, 2013
can I install and Cisco WAAS and Cisco Prime Network Analysis Module (NAM) together on a single Cisco Service-Ready Engine (SRE) 910 module? Or it can only run 1 of the software?
View 2 Replies
View Related
Dec 5, 2011
I have some confusion about some hardware components. I watched the video datasheet of cisco routers and switches. In cisco 2901 and 2911 models of routers there is service module . What is meant by service module. what does it do ? If we buy a new 6500 switch, what are the components we get bydefault. Is there any special configuraton to be done for 6500 . like Sup engine config etc. What is the difference between ASIC and Sup engine ? In which slots, we need to insert Supervisor Engine ? does it vary with the model . (6503, 6505, 6509, 6513 etc).
View 6 Replies
View Related
Jun 3, 2013
Is there any risk to install an HWIC-2FE card into a production 3845 router while it is in a powered up state? Is it recommended to power it down first, then install it?
View 3 Replies
View Related
Mar 20, 2013
I just got 2 Cat6504 Chassis and 2 ASASM pluged in them. show version from submodule ASA as follow:
SVC-APP-HW-3#show ver
Cisco IOS Software, trifecta Software (trifecta-SP-M), Version 15.1(1)SY, RELEASE SOFTWARE (fc2)
[Code].....
I want to upgrade new OS for ASA to 8.5 (asa851-smp-k8.bin) but after copy this soft to the module, I can not "write" command or when I reload this box, everything was no changed. SVC-APP-HW-3#write startup-config file open failed (No such device)
View 2 Replies
View Related
Mar 27, 2012
I am currently installing a NM-AIR -WLC 6 wireless module in a 2811 and its giving me the follwing errors below and status.I have checked the trouble shooting pdf and says might be possible hardware error. [code]
View 4 Replies
View Related
Sep 1, 2010
Does ACE service module support SHA2(256) certificates? I see that private key generation defaults to SHA1 and does not provide any option, also the cipher suites in SSL parameters map do not show SHA2 options. Can it handle SHA2 in any software release? I am currently running A2(2.3) build 3.00
View 6 Replies
View Related
Dec 2, 2012
My ACE module ACE30-MOD-K9 crashed today, and at the show ver output i see "last boot reason: Service "cfgmgr" ".the curent version we running is Version A5(1.2) [build 3.0(0)A5(1.2).
After doing some research i found known bug that supposed to be fixed in this version: CSCtu36146
CSCtu36146—The ACE becomes unresponsive due to a configuration manager (Cfgmgr) process failure with the last boot reason: Service "cfgmgr."
View 2 Replies
View Related
Apr 9, 2013
I want to add module of WS-X6716-10GE(-3C). The type of 6500 isCisco WS-c6509-e (r7000) processor (revision 1.2).Can I add this module to this type of 6500?Do I need to reset the 6500 in order to the 6500 receive the module?
View 2 Replies
View Related
Jun 6, 2013
I'm migrating from a failover pair of FWSM modules across to a failover pair of ASA Service Modules. In order to avoid a "big bang" switchover I intend to migrate subnets from one to the other over a protracted period.With that in mind, whether there is any restriction on having FWSM and ASASM modules in the same chassis? A trawl of the relevant documentation hasn't revealed anything.In this specific case it is Catalyst 6509E VSS chassis pairs with Sup-2T.
View 1 Replies
View Related
Jan 12, 2013
i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies
View Related
Aug 24, 2011
I'm looking at upgrading our FWSM modules in our 6500's. They're the WS-SVC-FWM-1 modules.
We're running on version 3.2(12) at the moment and I'm looking to jump up to 4. Any recommendations around whether I should to go to 4.1(6) or 4.0(16)? There aren't any features in particular that I would need in 4.1 but want a good stable base to sit on for 12 months until I look at this exercise all over again.
View 5 Replies
View Related
Mar 9, 2007
how to configure FWSM module in cisco core switch 6500
View 2 Replies
View Related
Apr 12, 2012
Is it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies
View Related
Jan 24, 2013
1) Does the 6500 series router support supervisor module redundancy like the 7304 does? IE, can I put two identical sup720 modules in the chassis for failover?
2) Can I use any ethernet interface on any line card on the 6500 series for router interfaces? If not, which line cards work as router interfaces?
3) Differences between the 6500 series and the 7600 series? Can I use a sup720 modules from a 6500 in a 7600?
View 4 Replies
View Related
Jun 10, 2013
i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies
View Related
Jan 21, 2012
As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies
View Related
Sep 20, 2012
I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
View 1 Replies
View Related
Feb 29, 2012
i want to check if cisco2911-sec/k9 can support IP service image? what PAK(license) can be bought to activate the IP service feature set?
View 1 Replies
View Related
Aug 8, 2012
When you use the command switchport trunk allowed vlan add [vlan-id]There should be no drop in service to the existing VLANs, correct? I am trunking from a 7K to a 2960S via 2G PoCh.
View 2 Replies
View Related
