when I do a show module in my cat 6509, the standby sup is saying unknown, it has the same IOS as the primary card.
what does this mean? are there any tests I can run on the card?
I have couple of SFP and most of them are working fine except this:-
Nexus7000# show interface ethernet 6/31 transceiver details
[code]...
a) What is the reason this is not getting recognized?
b) Is theSFP SFBR-5766PZ-CS1 plug and play in the 7000 Nexus?
We ordered the wrong part number for a Cisco 4506 non-E chassis, the part number is: WS-X4624-SFP-E and the device is showing "Unsupported module"; What would the part number be for the non-E? WS-X4448-GB-SFP,Catalyst 4500 48-Port 1000Base-X (SFPs Optional) ?
View 1 Replies View RelatedWe have supplied Cisco Swtch 2960 with gig SFP modules. It is working fine. However, when I do a show inventory it show proper part no. for the switch chassis but for the GLC T module it shows as unspecified in the PID column.
View 1 Replies View Relatedwe are planning to implement a VSS solution with a 6500 series switches with sup 2T. We also need to include an ASA service module on the design, however the budget is not enough to buy two asa service modules. So i want to know if is possible run a VSS cluster, whit only one ASA service Module. and also i would like know what happens if the single ASA service module fails? can the switch cluster continue operating just as if there is not a firewall installed?
View 1 Replies View Relatedwe have 6500 cisco switch as a backbone switch in universty. When ı want to look mac addres table , it does no show all mac address.ı mean if ı type ;show mac address-table there are not all mac address.
View 3 Replies View RelatedCisco IP phones attached to a Moduke in one of my Cat6500 access Switches suddenly went down. Upon closer inspection of the Switch Sys log, I observed the following Sys log error messages: [Module 9 is experiencing the following error: Inline Power Module - PS Voltage bad. ]A sh Mod output indicates the PoE daughter card and Main Module are "ok" - see attached output. It appears issue is related to the the actual Power Supply module and not the blade module and installed PoE Daughter card. I am inclined to open a TAC case for a PS replacement, but wanted to see if this can be resolved without a hardware replacement. At this time all 48 IP phones attached to this module are out of Service.
View 2 Replies View RelatedI have a 6500 switch and i recently removed a module (line card) from the switch. The problem is that the port configurations of the removed module still exhists in running configuration. I was not aware of the right procedure,[URL] however, i would like to know whether it resolves if i reboot the switch.
View 1 Replies View RelatedAfter inserting a RSP720-3C-10GE in module 6 and running the show module command display the following [code]what is the meaning of the UnKnown on the oline diag status ?
View 1 Replies View RelatedI have the WRT400N router with the latest firmware. Recently I have noticed a device in my DHCP that I do not recognize. It is not device I own (believe me, I have racked my brain and confirmed) as it shows as an Acer pc. I cannot ping the IP address however. I have rebooted my router several times thinking maybe it's a former connected device but saved in memory but it keeps coming back. I am thinking possibly it is someone hi-jacking my Internet, but not sure. I am using WEP security but it shows a LAN connection which is strange for a wireless device. The only hard wired pc is my HP.
View 3 Replies View RelatedI have connected 2 SG500x switches using an SFP-H10GB-CU1M SFP+ Copper Cable module. Since the port shows as a 10G port, I would expect the speed to show as 10G as well. However, it shows as "Unknown". This doesn't leave me with confidence that it is being recognized properly. The link is working properly, but I haven't run tests to verify if I'm getting full 10G throughput or not. Shouldn't it show 10G as the link speed?
View 12 Replies View Relatedhow can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedI have been having following situation on my WAN facing interface on Cisco2911 where the same number of broadcast, multicast and unknown protocol drops is happening. Not sure but some applications are struggling to run over on the WAN.
[code]....
when I want to recover my 2960 switch in rommon mode with xmodem command, It shows me these errors. when I reset the switch, still shoes these errors:
Unknown cmd: 1;2c1;2c[?1;21;2c[?1;21;2c[?1;2;21;2c[?1;2[
switch: ?1;2c[?1;21;2c[?1;21;2c
switch: ccknown cmd:
*** line too large *****tch: c1;2[?1
switch:
Unknown cmd: cc?1;2c[?1;21;2c[
[code]....
We are using 3825 Cisco router with IOS version 12.4(24)T2. The unknown protocol drops on our GigabitEthernet0/1 interface is increasing. This interface is connected to our modem. What could be causing this unknown protocol drops?
cnshaccent-gw-2#sh int GigabitEthernet0/1
GigabitEthernet0/1 is up, line protocol is up
Hardware is BCM1125 Internal MAC, address is ffff.ffff.ffff (bia ffff.ffff.ffff)
[Code]....
I want to add module of WS-X6716-10GE(-3C). The type of 6500 isCisco WS-c6509-e (r7000) processor (revision 1.2).Can I add this module to this type of 6500?Do I need to reset the 6500 in order to the 6500 receive the module?
View 2 Replies View Relatedi have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies View RelatedI have an ACE10-6500-K9 (Application Control Engine service module for Catalyst 6500) but I can't access it because I lost the admin password.I would like to know how to perform a Password Recovery Procedure on this device.Is it similar to the password recovery procedure on an ACE 4700 appliance?
View 2 Replies View RelatedI'm looking at upgrading our FWSM modules in our 6500's. They're the WS-SVC-FWM-1 modules.
We're running on version 3.2(12) at the moment and I'm looking to jump up to 4. Any recommendations around whether I should to go to 4.1(6) or 4.0(16)? There aren't any features in particular that I would need in 4.1 but want a good stable base to sit on for 12 months until I look at this exercise all over again.
how to configure FWSM module in cisco core switch 6500
View 2 Replies View RelatedIs it possible to modify conf with snmp on ace module like others 6500 catalyst ?Is ace answer to snmpset cmds ?
View 1 Replies View Related1) Does the 6500 series router support supervisor module redundancy like the 7304 does? IE, can I put two identical sup720 modules in the chassis for failover?
2) Can I use any ethernet interface on any line card on the 6500 series for router interfaces? If not, which line cards work as router interfaces?
3) Differences between the 6500 series and the 7600 series? Can I use a sup720 modules from a 6500 in a 7600?
i have a cisco router (3900 series) and a add on module (4 x 1 Gig port module). For some reason i cant seem to port channel them and cant do routing (can set an ip address on those ports). I can do port channel and routing on on-board ports. Do i have to enable any commands to do this ?
View 3 Replies View RelatedAs per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
Was wondering if anyone has ever hot ADDED, not swapped, an expansion module in a 5548up. Is a switch reboot required?I looked at the H/W install guide and it does not mention anything.
View 3 Replies View RelatedMy C6506 USING ws-sup720-3B, i upgrade the IOS to the latest release of 12.2(33) SXJ1 IOS version. After upgrade and reload the machine got one module cannot be detect..WS-X6416-GE-MT, 16 port 1000mb MTRK ethernet module. The version of this are:
-HW 1.0
-FW 5.3 (1)1
-SW 8.5 (0.46) RFW
Question 1: Any tools available on cisco to check out the hardware/software compabiity feature?
Question 2: Any release note, compability matrix table etc resources.
Recently we ha a Nexus 7010 with a module frozen that was OIR (Online Remote and Insert) but do not work until reload the Nexus 7k.The command "show tech-support" has the following:
exception information --- exception instance 64 ----
Module Slot Number: 1
Device id : 147
Device Name: 0x93
Device Errorcode: 0x9329201
[code].....
Was is Excessive Interrupt Events? Can this "Minor Error" frozen the system?Is the port 42 on module 1 affected? o was 42 ports?
Can the encryption module (DES/ 3DES/AES/SSL VPN Encrytion/compression) for Cisco Router 3845 able to support the external connection from other high end router, for example cisco 7200? What is the maximum bandwidth, load and concurrent connection it can support?
View 1 Replies View Relatedwhy is not possible to put a WS-X4712-SFP+E - module into an R-E chassis?The module has the same connection to backplane as the WS-X4748-UPOE+E and this one works in a R-E chassis.I know the restriction of Cisco that the 4712 is only supported in 4503-E, 4506-E,4507+E and 4510+E, but why?Are there hardware-restrictions, is the backplane different?
View 2 Replies View RelatedI have a pair of 6509-E Switches running VS-720 Supervisors. We are planning to add Ace Module onto the 6509-E. Will IP Base Image suffice the requirement? Will Ace Module work with only IP Base Image?
View 1 Replies View Related