As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?
View 5 RepliesI have a 4500 and 6500 that I'd like to be able to limit the bandwidth of layer 2 switchports. So for instance I have all GB blades but certain servers I'd like only to have connections of about 5 Mb per second or 15 Mb per second etc.
View 1 Replies View RelatedIt is said that the switching fabric of WS-C3750X-24T-E is 160Gbps.Could any body tell me what is switching fabric, any relevance or difference from forwarding rate?,Is there any document to know how will the switch reach the 160Gbps full switching fabric performance?
View 5 Replies View RelatedI am looking at the utilization on a Catalyst 3560-E. I am running a test with eight 1 GIGE links RXing at 95 % utilization. All of the traffic is going to a TenGigE port. The device on the TenGigE port is echoing back all of the traffic received, so the 1 GIG links are TXing at 95% as well.When I do a "show controllers utilization", the port utilization numbers are correct, but the fabric utilization is higher than I would expect. The fabric should be 128 gigbits / second in this switch, and there is 7.6 gigabits TX/RX to the ten gig port. The fabric utilization is at 49%. I would expect 7.6 / 128 = 5.9% or possible double that. [code]
View 8 Replies View Relatedwe installed copper and fiber sfp modules in the 2232PP and none would link up. we pulled the sfp modules out and entered the speed 1000 command and re-inserted the module with no success. the same sfp modules works fine in every other cisco device. we must be missing something. running latest nx-os software.
COH-Nexus-02# sh int Eth101/1/1 status
--------------------------------------------------------------------------------
Port Name Status Vlan Duplex Speed Type
--------------------------------------------------------------------------------
[Code].....
Need clarification on the VPC with 5k and 2248 Fabric Extenders. My question is can each fabric extender uplink to two different 5ks, and at the same time, have servers connected to two both fabric extenders with a VPC.So basically, the server NIC will team with two different fabric extenders, and each fabric extender will connect to two different 5k's.
View 3 Replies View RelatedAs per my understanding, Cisco Nexus 2232 can only connect to HP c7000 Chassis if we are using a Pass Through Switch in the HP c7000. Cisco Nexus 2232 can only connect to End Hosts and not to a switch. Is there a New Feature added in Nexus 2232, which enables it to connect to a Switch like HP Flex Fabric ?
View 1 Replies View RelatedHow to properly power down the Nexus 5000 and the fabric interconnect switches? I have looked up and down cisco's and google web for steps, but they are all coming back with the answer to just disconnect the power cables after you have power down all the windows os and exs servers. Before i do that, I just wanted to make sure that that's the correct way to do it or if there are actual commands that I will need to run on the devices to properly power down. I know that the FI do have a command to reboot, but i need them to completely be power down.
View 3 Replies View RelatedThere is a cisco ws-c6509,recently it appear error log “%FABRIC-SP-6-TIMEOUT_ERR: Fabric in slot 5 reported timeout error for channel 11 (Module 3, fabric connection 1)”. When I reload the device,the error log disappear.But a few days later,it appears again.I try to replace the slot 3 (WS-X6704-10GE),the error log continues.The IOS version is 's72033_rp-ADVIPSERVICESK9_WAN-M), Version 12.2(18)SXF8"
View 1 Replies View RelatedWhat s the fabric speed (backplane speed) of a Nexus 2232 10G EX?What is the forwarding rate (Mpps) of the same 2232 FEX?
View 6 Replies View RelatedI have been tasked to replace the existing Cat 6500 and 3750 switches by Nexus 7000 and Nexus 2000.I was told initially my boss plans to get 2 x Nexus 7000 and then eventually blow up to 4 x Nexus 7000s.For Nexus, is there a list of tasks / points that i need to consider for building the initial design?
Can i just link the Nexus 7000 like the following?
N7k-A ========= N7k-B
| |
lots of N2ks lots of N2ks
how can we upgrade 6500 non modular ios to normal 6500 ios?
View 5 Replies View RelatedI am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
snmpwalk -v2c -c "removes" sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP. why the value is so high on the switching processor ?
Any example to limit the bandwidth using the MAC address on 2960 ? I want to limit the bandwidth (IN / OUT) of a server only for Internet flows.
View 2 Replies View Relatedwill encrypting traffic: esp-aes 256 esp-sha-hmac across a WAN circuit drop a nics performance by half?
View 6 Replies View RelatedI would like to connect to a 1Gb routed uplink, and then impose bandwidth limits (via shaping/policing/whatever) on a per port basis. The ports could either be configured to route, or as switchports on separate VLANS. I'm trying to identify hardware that will let me do this. The set up I have in mind is shown below.
I am wondering if the IP Services Adv software on that switch will allow that functionality?
They have a /28 wan adress coming from ISP, that gives out 100Mbps, going to a Cisco 2960S switch (ver. 12.2) the switch is only holding 1 vlan. Connected to the 2960 are 3 firewalls/routers from other manifactors, each creating their own network. The customer wishes for a solution where each final FW/router gets minimum 33% and maximum 100% of the bandwidth, depending on how much each final Fw/router are in use.
View 1 Replies View RelatedFor intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?and on 3750 switches, do we need to enable the "ip routing" command manually for intervlan routing?
View 1 Replies View RelatedI'm looking to restrict Inter-VLAN routing through L3 switch (cisco 6500) and wanted to know best possible way to do it. I used VACL and achieved success to some extent, but my config is making clients take up to 5-6 mins to authenticate IP address from the DNS (bootps).My VACL config was as follows:
Subnet to restrict is 10.100.15.0 (VLAN 15)
STEP 1: Created extended ACL to allow bootpc/bootps through DNS
ip access-list extended EACL_DNS
permit udp any eq bootps any
permit udp any eq bootpc any
STEP 2: Created standard ACLs to allow only relevant subnet, server VLANs & some IPs from other subnets for printers/scanners etc.
ip access-list standard SACL_VLAN_15
permit 10.100.15.0 0.0.0.255 (the subnet I'm restricting)
permit 10.100.50.0 0.0.0.255 (server VLANs)
permit 10.100.25.45 0.0.0.0 (printer in another VLAN which has to have access in VLAN 15)
STEP 3: Created VLAN access list
vlan access-map VACL_15 10
match ip address EACL_DNS
action forward
vlan access-map VACL_15 20
match ip address SACL_15
action forward
STEP 4: Applying VLAN Access list on VLAN 15 vlan filter VACL_15 vlan-list 15 Though the above works, below is noted:
1. I'm still able to PING 10.100.15.2 (the switch virtual interface) from outside the subnet, which I don't intend to do so. Howeve all cients in the subnet have no connectivity from outside the VLAN 15.
2. As mentioned its taking quiet some time to negotiate with the DNS server at system boot time.
i would like to check out what's the difference between the naming convnetion for the 6500 IOS.
I read the data sheet to support my POC deployment to support NCS v.1 the 6500 IOS need to upgrade to 12.2 (33) SXI
Is it able to work if i using SXJ instead of SXI, with the same IOS version 12.2 (33)?
I have tried to test copy tftp: numerous time with no success. I believe the reason it is failing is my laptop to Ethernet port is in vlan 62 and the tftp process operates in a different IP space.I am using gig 7/1 and configuring my laptop nic for x.x.x.254 mask 255.255.255.0. I can ping from laptop to gateway) and I can ping from the switch to my laptop using ping vrf production x.x.x.254. Can you tell me what vlan I need to set my laptop connection in or if there is something else I need to change to make tftp work on vlan62?Does TFTP only work in vlan1 or can it be changed?
View 2 Replies View Relatedhow to upgrade IOS in switch 6500 connect in VSS from 12.2(33)SXI IOS to 12.2(33)SXJ?
View 3 Replies View RelatedWe are setup like a hotel style workers camp. We have wings full of rooms and residents with 3750 stacks in them. Those switches connect back to our core 6500's. The network is mostly all Layer 3, interfaces are routed with IPs.
When it was built before my time they included an ACL for each wing so that residents couldn't access internal devices (IE SSH to 6500) but I've come to notice it's not working.
I see hits on the ACL for accepts but nothing is hitting the deny rule at the top.Here is the configuration below:
mls qos aggregate-policer INTERNET1 24000000 80000 80000 conform-action transmit exceed-action drop
mls qos aggregate-policer INTERNET2 24000000 80000 80000 conform-action transmit exceed-action drop
mls qos aggregate-policer INTERNET 24000000 80000 80000 conform-action transmit exceed-action drop
[Code] ....
On googling I came across documents that say OTV (Overlay Transport Virtualization) is supported on Cat 6500. Any authentic information whether OTV is supported on Cat 6500, especially with Sup-720B? FYI, Cisco Feature Navigator does not mention it.
View 1 Replies View RelatedSUP2T-D#sh proce cpu hist
11111111111 1111 1111 1111 1111
0000000000099999000099999000099999999990000999900009999999
0000000000099999000099999000099999999990000999900009999999
100 **********************************************************
90 **********************************************************
80 **********************************************************
70 **********************************************************
60 **********************************************************
50 **********************************************************
40 **********************************************************
30 **********************************************************
20 **********************************************************
10 **********************************************************
0....5....1....1....2....2....3....3....4....4....5....5....
0 5 0 5 0 5 0 5 0 5
CPU% per second (last 60 seconds)
SUP2T-D#sh proce cpu sorted
CPU utilization for five seconds: 100%/83%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
416 3324188 879928 3777 13.05% 14.42% 14.45% 0 Spanning Tree
633 104408 5091 20508 1.50% 0.53% 0.45% 0 Env Poll
75 22000 298 73825 1.10% 0.13% 0.07% 0 Per-minute Jobs
168 69696 163563 426 0.39% 0.23% 0.22% 0 slcp process
2 532 1010 526 0.07% 0.00% 0.00% 0 Load Meter (code )
I am trying to guarantee 100mbps for a vlan across a gig link. I have done some research and found this command for switches
mls qos srr-queue input priority-queue 2 bandwidth 20
However it doesn't seem to work for my 6500. I know the 6500 uses PFC for QOS but I have no idea how it works. how I can guarantee a vlan 100mbps across a 1gig link?
We are getting ready to start testing Quad VSS for our production VSS environments we have done the research and per documentation it seems pretty straight forward.
I want to make sure that the dual to quad VSS is easily done across our multiple VSS setups and I am curious of those that have done this already have you ran into any gotchas on the turn up of the ICS Sup?
Also, just a ICS in a single chassis instead of one in both chassis of the VSS?
In one of our environments we have all single home devices going to VSS switch 1 and only dual homed devices. going to switch 2 so may be desireable to only install an ICS in the switch 1 VSS.
Cisco 6500 with 2T supervisor engine with following software Cisco IOS Software, s2t54 Software (s2t54-IPSERVICESK9-M), Version 15.0(1)SY1, RELEASE SOFTWARE (fc4)
The problem is that, I am not able to configure Multilayer Switching (MLS) (mls rp ip) in the global config command. Although the "mls" is visible on the config menu. but when I say "mls ?", the router prompt "unrecognize command"
Not sure if SUP 2T support MLS or it come with different name.
I have WS-C6509-E chassis with VS-S2T-10G supervisor.
Currently I have IOS " S2TIBK9-15001SY - Cisco CAT6000-VS-S2T IOS IP BASE FULL ENCRYPT "
Can I upgrade the IOS to " S2TISK9-15001SY - Cisco CAT6000-VS-S2T IOS IP SERV FULL ENCRYPT " without purchasing this IOS?
Will I face issue in TAC cases?
I used to "ip routing" command in order to enable inter-vlan routing, for example with 3750 cisco. I have a 6503 cisco with SUP720 MSFC3. I was able to create some vlans but I can not configure inter-vlan routing.
sw#conf t
Enter configuration commands, one per line. End with CNTL/Z.
swsur(config)#ip routing
[Code]....
For intervlan routing, Is 'IP routing' command enabled by default on a 6500 series switches based on the IOS?hes, do we need to enable the "ip routing" command manually for intervlan routing?
View 2 Replies View RelatedIs there a way I can find out the amount of bandwidth i'm using on a particular interface on a 4507 cisco multi-layer switch? It is a gig port and I have it setup for monitoring (spanning) and I see packets being dropped in the "Total Output Drops" area. To me it looks like it must be exceeding the 1gig limit but I don't know a way to check to make sure. I also have the queueing strategy set to FIFO.
View 3 Replies View RelatedI have ciscl catlyst 2960 8port switch, (flash:c2960-lanbasek9-mz.122-50.SE4/c2960-lanbasek9-mz.122-50.SE4.bin).
and in need to configure bandwidth limit for one of the port as a 1Mbps.