Cisco Switching/Routing :: QOS On 6500 Switch?

Feb 17, 2013

I am trying to guarantee 100mbps for a vlan across a gig link.  I have done some research and found this command for switches
 
mls qos srr-queue input priority-queue 2 bandwidth 20
 
However it doesn't seem to work for my 6500.  I know the 6500 uses PFC for QOS but I have no idea how it works.  how I can guarantee a vlan 100mbps across a 1gig link?

View 3 Replies


ADVERTISEMENT

Cisco Switching/Routing :: IOS Copy For Switch 6500 With Sup-720

Feb 13, 2013

I have 2 Chassis 6506-E with sup 720. one of them work properly(Switch1) but another(Switc2) not boot form bootdisk and go to ROMMON mode. I Captured IOS from Switch1 with tftp but I cant Copy this image to switch 2 with tftp.

View 4 Replies View Related

Cisco Switching/Routing :: 6500 Series Switch - TCP Adjustment

Oct 14, 2012

I have a routed interface on a Cisco 6500 Series switch.  I am trying to find a way to adjust the tcp mss.To date I have not yet been able to find a way to accomplish this.  Is this just not supported?

View 3 Replies View Related

Cisco Switching/Routing :: Switch 6500 Policy Map Inbound

Jun 9, 2013

ON switch 6500 i have configured an interface vlan x and applied policies on inboud and outbound directions as per below: [code] But the problem i am facing is that the policy outbound works ok , but the policy inbound doesnt work at all. specifically it doesnt match anything. [code]

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Power Off Core Switch?

May 31, 2012

we need to relocate our core switch 6500 with sup 720 to another bldg
 
what is the command to gracefully shut it down I mean power off
 
I was told one can just switch off the power

View 4 Replies View Related

Cisco Switching/Routing :: 6500 Changing Switch Configuration

Aug 27, 2012

I am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !

View 3 Replies View Related

Cisco Switching/Routing :: 6500 Switch Interoperability With Other Vendor?

Apr 3, 2013

I tried many different things to get the accurate answer for my issue. I wanted to know, will i face any connectivity or looping issue in the network if i connect Broacade SAN switch on a cisco 6500 switch.Also need to know to maintain a DATA DOMAIN which SAN switch is better? Cisco or other vendor.

View 2 Replies View Related

Cisco Switching/Routing :: Pm Scp Process 100% And Switch 6500-E Crash?

Oct 24, 2012

The switch 6500-E is frequently crashing whenever the pm scp process reach 100% .I got it under the  command "remote command switch show proce cpu".How to solve the problem. I opened the TAC and the engineer says to upgrade the image12.2(18) sxf.Is there any other work around that would avoid to reimage the switch and reloading.

View 1 Replies View Related

Cisco Switching/Routing :: 6500 Switch Won't Accept Long IOS Name

Mar 29, 2012

I'm in the process of upgrading the IOS of our 6500 switch and unfortunately, the images were messed up by other users. Here's the output of show redundancy. [code] would i have any issues if I reload this slave supervisor engine to load the SXI8 IOS?

View 5 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Switch Architecture

Jul 16, 2012

one of the most widely deployed switches in the world. The "Swiss Army knife of network", can do routing, switching, security, wireless and almost everything that you would want your core switch to do. Remember to use the rating system to let Akshay know if you have received an adequate response. 
 
Akshay might not be able to answer each question due to the volume expected during this event. Remember that you can continue the conversation on the Network Infrastructure sub-community LAN, Switching and Routing discussion forum shortly after the event.  This event lasts through July 27, 2012. Visit this forum often to view responses to your questions and the questions of other community members.

View 22 Replies View Related

Cisco Switching/Routing :: 6500 - Changing VTP Mode Of A Core Switch

Oct 14, 2012

We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.

View 7 Replies View Related

Cisco Switching/Routing :: Migrating Core Switch From 3750 To 6500?

Jun 5, 2013

I am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.

View 6 Replies View Related

Cisco Switching/Routing :: Spanning-tree Change On VSS 6500 Switch?

Jun 19, 2012

changing the Spanning-tree mode on a live 6500 running in a VSS mode?If so what are the things to watch out?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Switch Booting - Hardware Failure On SUP

Jul 7, 2012

One of my customer had a problem with A/C and the room temperature reached almost 50 C. We came to the site and saved the configuration, took a backup and shutdown the switch.
 
After the A/C problem is resolved, we tried to power-on the switch .. and we found that it is going to the rommon.
 
I put "boot" command to boot from the bootdisk, but I am getting the following error:
 
Code...

I tried to search it, But it is resulting in that most probably it is a hardware failure on the SUP.

View 6 Replies View Related

Cisco Switching/Routing :: Clearing Single ARP Entry In 6500 Switch?

Feb 2, 2009

Is there any way to clear a single ARP cache entry on the 6500 switch ?

View 8 Replies View Related

Cisco Switching/Routing :: Connect 6500 With 4948 Switch Using 10G Optics

Jul 8, 2012

I need to connect a 6500 switch with a 4948 switch using 10G optics. On 6500, line card used is WS-X6704-10GE and I am aware that WS-X6704-10GE is a xenpak and 4948 ports are X2. What is the way to make the connection between xenpak and X2 work?

View 3 Replies View Related

Cisco Switching/Routing :: Combined Power Mode For 6500 Switch?

May 18, 2012

The following discussion is based on cisco cat 6500 switches with two power supplies: p1 and p2.  . Both power supplies are running in combined mode .Each power supplies is rated with 500 watts max( I just picked 500 watts for simplicity)Combined mode In combined mode, each power supply provides approximately 83% of its  capacity to the chassis. This allows for greater utilization of the  power supplies and potentially increased PoE densities
 
1) Let say  our specific 6500 switch's configuration requires 1000 watts. We have two power supplies p1 and p2 ,each with rated power of 500 watts.  Both power supplies must operate in combined mode.  Will power supplies be able to meet the total load power requirement of  1000 watts?
 
Here is my understanding :The maximum power delivered by each power supplies is 83 percent of its rated power, assuming power supplies are running in combined mode.
 
So Maximum power delivered by power supplies

=  83% of p1+ 83% of p2
=  83% of 500 + 83% of 500
= 415 +415
=830 watts

Thus the required load of 1000 watts can not be met by our power supplies in combined mode. 
 
2 )Suppose our switch's switch configuration needs 500 watts.  Again our power supplies each rated with 500 watts, are configured for combined mode. How much power is being delivered by each power supply?  Is it 83 percent of the total load i.e 500 watts?

View 4 Replies View Related

Cisco Switching/Routing :: 6500 - How To Set Switch On Auto Terminal Server

Apr 22, 2012

I have a switch(6500) with 2 vlans(2 SUBNETS) and from the other side of my network i have 2 terminal servers.

I want to have a VIP in my 6500 switch which i have the 2 vlans and when the first vlan(network) try to connect to the VIP

my switch will forward to first terminal.When the second vlan try to connect to VIP the switch will forward to second terminal.
 
I'd like the switch to decide in wich terminal server will forwared the packet based on source network.
 
I am not sure how i can do this???I use VIP with SLB???I use NAT???PBR?

View 4 Replies View Related

Cisco Switching/Routing :: Enable STP To Specific VLans In 6500 Switch?

Jun 13, 2013

I have 6500 with this STP configuration:
 
spanning-tree mode rapid-pvst
no spanning-tree vlan 1-4094
 
I need to enable STP on vlan 100 and vlan 103.
 
When I do "spanning-tree vlan 100,103 root primary" and then "show spanning-tree".I see that STP is not enable on these vlans (100,103).
 
I tried to do "no spanning-tree vlan 1-99,101,102,104-4094" and it is not work.
 
There is a way to enable STP on vlans 100,103 without to do "spanning-tree vlan 1-4094"

View 1 Replies View Related

Cisco Switching/Routing :: Etherchannel - Redundant 6500 To 3750 Datacenter Switch?

Mar 27, 2012

I have 2 6504's running HSRP as my core.  They are each etherchannel'd to my Datacenter switch (3750 Stack) -- see image below.The problem i a having is with the etherchannel status:

Core1 PO11 status w (waiting)
Core2 PO11 status P(bundled)

DC11 PO48 status P -- but only to Core2 - the interfaces to Core1 are suspended. (See attached configuration documents)  None of the devices have any information in the logs.  I run this same configuration in my central location, but we are running Nexus 7000's.  With the 6500's, do I need to split the port channels on the 3750 to allow them to negotiate the etherchannel? If I split the portchannels, are there any concerns? Should I expect to see the etherchannel status as P (Bundled) or H (Hot-Standby)?

View 2 Replies View Related

Cisco Switching/Routing :: Layer 3 Port Channel From 6500 VSS Switch To Two Standalone

Jul 30, 2012

Configured Layer 3 portchannel from 6500VSS enabled switch to two different 6500 standalone switch. Configured first ip on VSS switch, second ip on standalone switch1 and third IP on standalone switch2. My question is
 
1. Will the portchannel be up?
2. If port channel is up, will I able to ping the connected IP's.

View 1 Replies View Related

Cisco Switching/Routing :: How ACL Respond On Normal Switch 6500 When Applied On Respective Vlans

Nov 22, 2011

I am confused on how acl's respond on normal cisco switch (eg.6500) when applied on respective vlans. this is my scenario:on a 6506, i have 2 main vlans in question: Vlan 100 ( vendor1 - 172.16.100.0/24 ) & Vlan 200 ( vendor2 - 172.16.200.0/24 ). the requirement is,
 
 - vendor1 should be able to access/ping vendor2 end points

- vendor2 should not be able to access/ping vendor1 end points

Now, if i ping from a host 172.16.100.11 in vlan 100 to another host 172.16.200.21 in vlan 200, will i be able to get a successful response ?

View 4 Replies View Related

Cisco Switching/Routing :: 6500 / 3560 - Get L2 Traffic Amount (bit / Byte) Passing Through Switch

May 30, 2012

We want to get L2 traffic amount (bit/byte) passing through a cisco switch (6500/3560 ...) for a specific VLAN. it can be via SNMP or CLI ...How can we do that?
 
note: there is no L3 interface on swtiches.

View 2 Replies View Related

Cisco Switching/Routing :: 6500 Configure Switch Layer 3 Port Connected To Firewall

Feb 26, 2012

I have a switch layer 6500  series connected to a firewall, the port configuration between them is  layer 2, in another words I do not configure an IP address in the Cisco  switch port to conected it in the firewall, but when a apply a policy on  firewall it lose communication with others vlans, just the vlan that is  connected between the switch and firewall works, attachment the design.  I think that is necessary to configure the connection between the  firewall and switch as layer 3 ( a port with IP address in the switch),  but I would like to know why? The switch is configured with about 10  vlan and it is a inter vlan routing, a default route is configured in  the switch where the gateway is the firewall.

View 5 Replies View Related

Cisco Switching/Routing :: WS-C6513 Command To Check 6500 Switch Performance / Resource Usage

Apr 25, 2013

I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.

View 3 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 Switch Support Multi-chassis EtherChannel Features?

Sep 26, 2012

I came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly  stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?

View 4 Replies View Related

Cisco Switching/Routing :: 6500 Ping Packet Drop From Core-Switch To Directly Connected Server

Oct 24, 2011

I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.

View 9 Replies View Related

Cisco Switching/Routing :: Any Challenge To Upgrade Core Switch 6500 Series From Nexus 7009 Which Runs NxOS

Jan 28, 2013

Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
 
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?

View 9 Replies View Related

Cisco Switching/Routing :: Convert Switch Port To Router Port On 6500

May 8, 2012

On the supervisor card of a cisco 6500 series, according to the following link, [URL] it only has 2 uplink ports on the card. Would I be correct in assuming that I only have those to ports that I can configure IP addresses on?
 
The cisco that is being devlivere is coming with a 48 port switch and 24 port fibre switch. Could I change any of those ports into a router port and configure IP addresses on those?
 
The supervisor card is a ws-sup-720-3b the 48 port switch is a ws-x6748-ge-tx the 24 port fibre switch is ws-x6724-sfp

View 3 Replies View Related

Cisco Switching/Routing :: Upgrade 6500 Non Modular IOS To Normal 6500?

Dec 21, 2011

how can we upgrade 6500 non modular ios to normal 6500 ios?

View 5 Replies View Related

Cisco Application :: Asymmetric Routing Seen In WAE When Using 6500 Switch?

May 23, 2011

When we do self diagnostic test for WAE connected to the 6500 switch i get warning as below. Due to this alert there is no major acceleration benfits by the WAAS
 
Test WARN  [tfo] WARN  ASYMMETRIC  Asymmetric routing is seen in the device Action:  Check router's network configuration and WCCP redirection on the router.usevwa1#
 
6509 switches has only L2 capability and does not do WCCP redirection. The WCCP re-direction is done by 2821 routers.Is there any command which needs to be given in 6500 switch to solve the issue

View 1 Replies View Related

Cisco Switching/Routing :: 6500 Switching Fabric Bandwidth 720 Is Calculated?

Jan 21, 2012

As per my understanding 6509 all slots are dual channel, so 9 slot * 40 per slot (20 g in and 20 g out) = 360 GB How cisco claim the 720 ?? What about the 6513 chassic switch fabric connection?

View 5 Replies View Related

Cisco Switching/Routing :: 6500 / High Switching Processor Utilization?

Sep 20, 2012

I am seeing a strange situation on my 6500 switch?By having snmp walk on '1.3.6.1.4.1.9.9.109.1.1.1.1.3' (== cpmCPUTotal5sec), I came to know that there are two processor and the cpu util for switching processor is gone to 88 % and some time creeps to 99 %.
 
snmpwalk -v2c -c "removes"  sw6500 '1.3.6.1.4.1.9.9.109.1.1.1.1.3'
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.1 = Gauge32: 12 (--- this is for CPU of Router Processor )
SNMPv2-SMI::enterprises.9.9.109.1.1.1.1.3.3 = Gauge32: 99 (--- this is for CPU of Switching Processor )
 
but when I do sh process cpu on the console, all looks normal as it shows cpu utilization of RP.  why the value is so high on the switching processor ?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved