Cisco Switching/Routing :: 6500 - Changing VTP Mode Of A Core Switch

Oct 14, 2012

We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.

View 7 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Changing Power Mode On 6500

Oct 2, 2012

We have two 6500s. One is running in power redundant mode and the other is running in combined mode.We need to change the one running in combined mode to redundant mode to ensure it can run ok on one supply if needed but I have a couple of questions.

1. Assuming that we are not oversubscribed on the power allocated, does changing the mode cause any disruption?

2. The switch running in combined mode seems to have allocated some power for an "Inline Local-Pwr-Pool" which is not allocated on the switch running in redundant mode (see attached). Does this allocation will be needed if we change the power mode?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Power Off Core Switch?

May 31, 2012

we need to relocate our core switch 6500 with sup 720 to another bldg
 
what is the command to gracefully shut it down I mean power off
 
I was told one can just switch off the power

View 4 Replies View Related

Cisco Switching/Routing :: Migrating Core Switch From 3750 To 6500?

Jun 5, 2013

I am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.

View 6 Replies View Related

Cisco Switching/Routing :: 6500 Changing Switch Configuration

Aug 27, 2012

I am going to change a running 6500 switch. I am missing a best pratice doc for changing a cisco switch configuration. My question is if a startup-config has an error (due to typo mistake, or due to comands not supported on latest IOS) and I do copy tftp startup-config then what will happen ? I want to make sure when I do "reload" the switch then it should boot normally with the latest startup config !

View 3 Replies View Related

Cisco WAN :: 3750 - Use Two Core Switch 6500 With Single Mode Fiber As Transport Equipment?

Nov 30, 2012

I have a requirement to connect two 3750 switch with 10G speed between two sites with 150km distance. We will lay-out our own fiber (48 core) between two sites. I just want to consult the following:
 
1. Could i use two core switch 6500 with single mode fiber as a transport equipment?

2. Or i need to use SDH equipment because of the distance concern? If so do i need a repeater?Could i use Cisco Metro Core ONS, which one?

3. Any other option to achieve this requirement?

View 4 Replies View Related

Cisco Switching/Routing :: 3750X / Core Switch In Redundant Mode?

Nov 18, 2012

Two Cisco 3750X can be stacked together to ensure redundancy.Is the attached topology feasible for access layer redundancy?

View 5 Replies View Related

Cisco Switching/Routing :: 6500 Ping Packet Drop From Core-Switch To Directly Connected Server

Oct 24, 2011

I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.

View 9 Replies View Related

Cisco Switching/Routing :: 6509 Core Switch Command / IP PIM Sparse-dense-mode

Oct 23, 2011

What is PIM? give me an example when I will use and not use the PIM command.

View 4 Replies View Related

Cisco Switching/Routing :: Any Challenge To Upgrade Core Switch 6500 Series From Nexus 7009 Which Runs NxOS

Jan 28, 2013

Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
 
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?

View 9 Replies View Related

Cisco Switching/Routing :: Combined Power Mode For 6500 Switch?

May 18, 2012

The following discussion is based on cisco cat 6500 switches with two power supplies: p1 and p2.  . Both power supplies are running in combined mode .Each power supplies is rated with 500 watts max( I just picked 500 watts for simplicity)Combined mode In combined mode, each power supply provides approximately 83% of its  capacity to the chassis. This allows for greater utilization of the  power supplies and potentially increased PoE densities
 
1) Let say  our specific 6500 switch's configuration requires 1000 watts. We have two power supplies p1 and p2 ,each with rated power of 500 watts.  Both power supplies must operate in combined mode.  Will power supplies be able to meet the total load power requirement of  1000 watts?
 
Here is my understanding :The maximum power delivered by each power supplies is 83 percent of its rated power, assuming power supplies are running in combined mode.
 
So Maximum power delivered by power supplies

=  83% of p1+ 83% of p2
=  83% of 500 + 83% of 500
= 415 +415
=830 watts

Thus the required load of 1000 watts can not be met by our power supplies in combined mode. 
 
2 )Suppose our switch's switch configuration needs 500 watts.  Again our power supplies each rated with 500 watts, are configured for combined mode. How much power is being delivered by each power supply?  Is it 83 percent of the total load i.e 500 watts?

View 4 Replies View Related

Cisco Switching/Routing :: Changing 4510-SUP-6E Redundant Mode To Share-Backplane Mode

Mar 12, 2013

I received the following info from Cisco's TAC and wanted to inquire further before I start reconfiguring the switch:
 
In a redundant Sup-6E setup, the following configuration is supported :
 
- 1 TenGig uplink on Active Sup and 1 TenGig uplink on Standby Sup
- 1 TenGig uplink on Active Sup and 2 Gig uplinks on Standby Sup
- 2 Gig uplinks on Active Sup and 1 TenGig uplink on Standby Sup
- 2 Gig uplink on Active Sup and 2 Gig uplinks on Standby Sup
 
If you invoke shared backplane mode, the following configuration can also be supported:
 
- 2 TenGig uplinks(blocking) on Active Sup and 2 TenGig uplinks on Standby Sup
- 2 TenGig uplink(blocking) on Active Sup and 4 Gig uplinks on Standby Sup
- 4 Gig uplinks on Active Sup and 2 TenGig uplinks(blocking) on Standby Sup
- 4 Gig uplink on Active Sup and 4 Gig uplinks on Standby Sup
 
Here's the command and information about the "shared-backplane" mode :- [URL]
 
Currently, we have 2  SUP 6-Es(Module 5 - Active and Module 6 - Stand-by) setup in a redundent mode. I am planning on changing the redundent mode to the shared backplane mode so I can use 2 TenGig converters to uplink 2 access-switches. We purchased 2 TenGig converters and here is how I am planning on using them:

1- One will be used  to uplink to two 3750 switches(stacked)
2- One will be used to uplink to a 2960 using a Gig SFP
 
My questions are:

1- Do I have to install the 2 TenGig converters(4-Gig Uplinks) in the same Module? Or can I use one one in module 5 and the second one in module 6?
2- Will changing the redundant mode to the shared backplane mode require rebooting the switch or disrupt the funtionality of the other linecards?

View 2 Replies View Related

Cisco Switching/Routing :: Convert CORE 6500 From VSS To Non-VSS?

Apr 17, 2012

how to convert the CORE 6500 from VSS to non-VSS?

View 2 Replies View Related

Cisco Switching/Routing :: Ip Address Is Pinging But Not Available In ARP From Core 6500

Apr 30, 2012

I have an Issue.In my networks, 1 single user is facing Network Slowness issue. i needs to check to which port user is coneected in switch to CHeck whether that port has any errors.But problem is, i am providing support from remote location.And my concern LAN segment is Very big,I have only user Ip address details,when i ping the Ip address from Core switch it is pinging. but when i give show ip arp & give Ip address then its not learning and listing out the Mac address to trace down to the specific port.

View 3 Replies View Related

Cisco Switching/Routing :: Dual Core / SUP 720 6500 IOS Upgrade?

Apr 29, 2012

Doing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]  
 
Script:
 
Backup
sh ver
remote command switch show version

[Code].....

View 6 Replies View Related

Cisco Switching/Routing :: 6500 / Connect A Juniper SRX Firewall To Core Switches?

Mar 17, 2013

Assume that we have 2 Cisco 6500 series which redundant via GLP, now my question is how can we connect a Juniper SRX firewall to our core switches?

View 2 Replies View Related

Cisco Switching/Routing :: 6500 - Changing LACP Loadbalancing Option

Oct 30, 2012

we have 6500 series switches by default all port channel loadbalancing is src-dst-ip.Now we have a requirement to change LACP load balance method to src-dst-port.
 
1) If we change LACP loadbalance method whar are the effects we are going have on our core network and all the existing servers

View 3 Replies View Related

Cisco Switching/Routing :: 6500 - Will Manually Changing EIGRP Router ID Cause Reconvergence

Nov 28, 2012

I have a pair of data center core 6500 is running a single EIGRP AS with the standard core redundant cross connects. Recently an SVI sub net was expanded from a /24 to a /23 and dropped out of the EIGRP routing table.  Subsequent trouble shooting lead to the router id being one using an IP address that is no longer active IP address. 

Reviewing old configurations I found, that year ago, the ip address used for the EIGRP router-id (10.100.106.3) was removed from the active interface and changed but the EIGRP router-id was not updated.  The switch has not been rebooted since, no loop back is configured and there is not a higher IP configured on an active interface. Reviewing documented material on it, I cannot find anything specific on this condition but do see in the discussions on duplicate IDs, that new route updates can be a problem. I know how to update the router id but I am looking for confirmation on what would be the impact when I add a new loop back and manually configure the router-id under the EIGRP process with the new loop back IP. 

My assumption is an EIGRP update and route re convergence with the standard 90 seconds of outage. How to confirm this is assumption is correct?  I have no test bed to find out myself without doing this on the active cores.

show version Cisco IOS Software, s72033_rp Software (s72033_rp-IPSERVICESK9_WAN-M), Version 12.2(33)SXI5, RELEASE SOFTWARE (fc2) show inventory NAME: "WS-C6504-E", DESCR: "Cisco Systems Cisco 6500 4-slot Chassis System"PID: WS-C6504-E  VID: V01, SN: <deleted> NAME: "1", DESCR: "WS-SUP720-3B 2 ports Supervisor Engine 720 Rev. 5.3"
PID: WS-SUP720-3B 
 
EIGRP configuration is pretty basic:  
router eigrp 10
network 10.0.0.0
redistribute static
passive-interface Vlan110
passive-interface Vlan80
[code]...

View 1 Replies View Related

Cisco :: Flash File Location In 6500 Core Switch?

Apr 18, 2013

what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.

View 4 Replies View Related

Cisco Application :: Configure New ACE 30 Module On Top Of 6500 Core Switch

Jan 12, 2013

i have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?

View 1 Replies View Related

Cisco WAN :: 6500 / 6513E - Filtering Core Switch Ports?

Apr 15, 2013

Nowadays i have a project @ my work , the project consists of replacing our Cisco 6500 Core Switch with two other Core switches 6513E .
 
Is there is any tool to filter which port is connected to which server with its mac address and IP?

View 1 Replies View Related

Cisco Security :: Configure FWSM Module In Core Switch 6500

Mar 9, 2007

how to configure FWSM module in cisco core switch 6500

View 2 Replies View Related

Cisco WAN :: How To Know That 6500 And 7600 Series Switch And Router Are Running In Native Mode Or In Hybrid Mode

Feb 26, 2013

How can we know that 6500 and 7600 series switch and router are running in native mode or in hybrid mode.

View 2 Replies View Related

Cisco Switching/Routing :: How To Configure 1 Core Switch 4500

Jun 2, 2013

i configure the uplinks as etherchannel, i configure two svi interface on core switch int vlan 51(192.168.51.1) and int vlan 50(192.168.50.0) for this two svi int i configured two dhcp pool , when any of the pc is requesting for dhcp add i am getting dhcp request failed/

View 7 Replies View Related

Cisco Switching/Routing :: 2960G Core Switch For 400 Users

Jun 7, 2012

I'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.

View 3 Replies View Related

Cisco Switching/Routing :: How To Connect Two Core Switch C4510R+E SUP 7-E

Nov 4, 2012

I have 2 units core swicth C4510R+E SUP7-E  need to connect together for redundant purpose , i bought also 4X 10GE uplinks for each core switches .May i know how i shall connect both core switches together using my spec Catalyst 4500 E-Series 12-Port 10GbE (SFP+) ?

View 6 Replies View Related

Cisco Switching/Routing :: EWA14 - High CPU Utilization In Core Switch

Dec 20, 2011

I am experiencing high cpu utilization in my 4000 series core switch.
 
I checked the loggs. i saw some strange loggs.
 
Please see the below logs:

Code...

What is the "invalidsourceaddresspacket" ?
 
Is this is due to some virus attack or something?? Also one more thing this switch is the Active router in HSRP.

View 12 Replies View Related

Cisco Switching/Routing :: 2960S Unable To Connect To Core Switch

Sep 21, 2012

I have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.

View 40 Replies View Related

Cisco Switching/Routing :: Connecting Core Switch To Firewall 3750x

Apr 13, 2013

I have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.

View 22 Replies View Related

Cisco Switching/Routing :: Change From 3com Core Switch By 2960?

Aug 30, 2012

choosing a core switch, to replace a swich 3com model 4924, its main function is to support a 4-LAN switch cisco 2960 (100 users) and a ring cluster of 12 servers.obs. Current 3com core switch has 56 Gbps performance and 41.6 million packets per second.

View 3 Replies View Related

Cisco Switching/Routing :: Upgrade Software Of Core Switch 4503e?

Nov 2, 2011

i am trying to upgrade the software of the core switch 4503e, i could not get the managemenet ip address up and running. what i did is the following :
 
interfave vlan 1
ip address 192.168.1.1 255.255.255.0
no shu
  
then my laptop ip address is 192.168.1.100 255.255.255.0?result pinging from CLI is request time out.is there any els command where i need to input ?

View 13 Replies View Related

Cisco Switching/Routing :: Very High CPU Utilization Core Switch 4503?

Feb 14, 2012

We  had a core switch(30 vlans) in our environment and it's noticed that  CPU utilization of the core switch is showing high during recent days. I  have checked logs and processes, but couldn't find the root cause. The  issue found only in the office hourly only(after that the cpu  utilization is idle and normal). I have already referred the following  link to troubleshoot the issue " [URL]
 
see the following outputs from the core switch
 
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms)   Invoked      uSecs   5Sec   1Min   5Min TTY Process
  30   6687557041432420936        466 47.52% 47.10% 45.98%   0 Cat4k Mgmt LoPri
  55  30667074884269560256          0 45.36% 45.50% 45.85%   0 IP Input
  29  28552856922870089254          0  3.59%  3.50%  3.57%   0 Cat4k Mgmt HiPri

[code]....
 
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
  
My queries regarding the issues are following
 
1) How can we find root cause regarding the high cpu utilization?

2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?

View 10 Replies View Related

Cisco Switching/Routing :: Upgrade IOS For Production Core 3750 Switch

May 7, 2013

I want to upgrade IOS for my production core 3750 switch. Below is Show version/fash output. I have IOS image "c3750-ipservicesk9-mz.122-55.SE7", need to confirm below concerns:-
 
1-As this is stackable switch do i need to upgrade on all Switch..i can see there are 3 flash while doing show flash?
2-Is above IOS image support with  my switch? do i able to enable ssh?
3-is flash memory is enough to succefully upgrade IOS?
4-Any other point which i should keep in mind before upgrading..any special feature which this IOS wont support.

View 11 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved