Nowadays i have a project @ my work , the project consists of replacing our Cisco 6500 Core Switch with two other Core switches 6513E .
Is there is any tool to filter which port is connected to which server with its mac address and IP?
we need to relocate our core switch 6500 with sup 720 to another bldg
what is the command to gracefully shut it down I mean power off
I was told one can just switch off the power
what is location of flash file in 6500 Series switch and how can we take back of IOS image for 6500 series.
View 4 Replies View Relatedi have configure new ACE 30 module on top of 6500 core switch , the issues am facing whenver i want to access to https://ACE_IP and after i enter the user name and the password , it's forwared me to the follwoing page: is there anything should i configure to avoid this page ?
View 1 Replies View RelatedWe have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies View RelatedI am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.
View 6 Replies View Relatedhow to configure FWSM module in cisco core switch 6500
View 2 Replies View RelatedI have a requirement to connect two 3750 switch with 10G speed between two sites with 150km distance. We will lay-out our own fiber (48 core) between two sites. I just want to consult the following:
1. Could i use two core switch 6500 with single mode fiber as a transport equipment?
2. Or i need to use SDH equipment because of the distance concern? If so do i need a repeater?Could i use Cisco Metro Core ONS, which one?
3. Any other option to achieve this requirement?
I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies View RelatedIs there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
Is it possible using any module in CW to get the MAC address and IP address of all switchports on a 6500?
View 6 Replies View Relatedhow to convert the CORE 6500 from VSS to non-VSS?
View 2 Replies View RelatedWe are using CISCO Catalyst 6500 switches as collapsed core/distribution switches (2 layer architecture). I want to connect approximatly 10 application servers to the network. Can I connect the servers directly to the catalyst 6500 switches using WS-X6148E-GE-TX line cards? The other option is to use access switchs and then connect the servers to the catalyst 6500 through access switch(Catalyst 3750).
View 6 Replies View RelatedI have an Issue.In my networks, 1 single user is facing Network Slowness issue. i needs to check to which port user is coneected in switch to CHeck whether that port has any errors.But problem is, i am providing support from remote location.And my concern LAN segment is Very big,I have only user Ip address details,when i ping the Ip address from Core switch it is pinging. but when i give show ip arp & give Ip address then its not learning and listing out the Mac address to trace down to the specific port.
View 3 Replies View RelatedDoing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]
Script:
Backup
sh ver
remote command switch show version
[Code].....
Assume that we have 2 Cisco 6500 series which redundant via GLP, now my question is how can we connect a Juniper SRX firewall to our core switches?
View 2 Replies View RelatedHow many of the 881 switch interface ports can be used as router ports, have used the 877 etc where i can use 2 but need a low cost router that supports 3 for routing. (needs to be physical ports)
View 2 Replies View RelatedIn my Company there is a core Switch 4500 series , to which in the 1st module servers are connected and in the second module 2960 , 3750 series Switches are connected, problem is that the Utilization of Core switch is very high and the core gets hanged. the configuration of the senerio is VTP domain i.e core is Server and the rest are Clients....
View 12 Replies View Relatedthere are more than 15 servers which include xen,esx,vmware,also san etc..which are connected to L3 core switch directly. And vlans are created for each.....xen,iscsi,vmware,xen,server. wanted to know is there any other technology other than directly connecting servers to core switch and assigning vlans that can be used in place?
View 4 Replies View RelatedWe have a L3 core switch with multiple VLANs setup. Is there a way to place an IPS so as to monitor the traffic passing between, lets say, VLANS 1-3 and VLANs 4-10?
View 3 Replies View RelatedI am facing issue with LMS 4.0. The Core Switch is showing in RED color,and device type as UNKNOWN. It was working fine but some how it is showing this problem.
View 14 Replies View RelatedJust received our new 6513E chassis and I am setting it up in the lab for testing. For prod we would like to run..
1 maybe 2 6704 10 gig cards
3 - 5 6748 cards
1 6724 SFP card
Sup720 setup, possibly upgrading to Sup32's in a few years, Right now for power supplies, I am using 2 WS-CAC-2500W ,But I have to run the supplies in combined mode to get all of the cards online.What power supply should I be looking to purchase for this chassis ?
We are close to receiving our new 6513E chassis which I will be running Sup720 cards in. This will be replacing our existing 6509 Sup2 setup in production. What current IOS version should I run on the Sup720 ? I would like to support SSH. The chassis will be populated with a couple of 6724 SFP cards, 2 6704 10 gig cards and a few 6748 line cards.Is there a good intitial config guide ?
View 6 Replies View RelatedI want my core switch auto failover to other route if the primary route is link down it will go to the secondary route
example
ip route 0.0.0.0 0.0.0.0 1.1.1.1
ip route 0.0.0.0 0.0.0.0 2.2.2.2 100
if my core switch detect next-hop 1.1.1.1 it will re-route and go to the 2.2.2.2 for the next-hop my core switch using static route and cant support ip sla
I am getting following error in Cisco 6509 switch.BUt there is no impact in the switch.
: %MAC_MOVE-SP-4-NOTIF: Host 0000.0c07.ac01 in vlan 694 is flapping between port Te8/1 and port Te7/1
29:33.959: %MAC_MOVE-SP-4-NOTIF: Host 0000.0c07.ac01 in vlan 269 is flapping between port Te7/1 and port Te8/1
[Code].....
I tried to implement WLC5508 in my network but when I came to connect it to the switch core which is a Catalyst 4000 the link didn't get up. This switch module is a fastethernet, I wonder if that might be the problem since I also tried connecting my laptop to the WLC and the link got up.
If that might be the cause, is it possible to get WLC to 100 Mbps?
What is the VPC configuration template with two core 6509 switch.Pls find the attachment for Network topology.
View 3 Replies View RelatedMy CORE Switch 4507R Suddenly restarted (Powe is good) , and gets the business down for 30 Mts,my boss came to me and asks why it has restarted , what is the root cause of this restart, i dont have any syslog or NMS enabled in my network to be informed
View 6 Replies View RelatedDHCP configuration on CISCO core switch 4507R switch.With one vlan and multipul vlan both configuration using any ip address range.
View 3 Replies View RelatedI got new task moving WS-3560X24 port layer 3 core switch from one branch to be moved to my branch and connect WS3560 layer 3 core switch my site network. Both core switch has got 3-4 cisco 2960 switch underneath and lots of vlan offcourse. I am thinking about creating etherchannel between these two switch.
View 2 Replies View RelatedI have a L3 core switch with multiple VLANs setup. Is there a way to place an IPS so as to monitor the traffic passing between, lets say, VLANS 1-3 and VLANs 4-10?
View 19 Replies View Relatedi configure the uplinks as etherchannel, i configure two svi interface on core switch int vlan 51(192.168.51.1) and int vlan 50(192.168.50.0) for this two svi int i configured two dhcp pool , when any of the pc is requesting for dhcp add i am getting dhcp request failed/
View 7 Replies View RelatedI'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.
View 3 Replies View Related
