Assume that we have 2 Cisco 6500 series which redundant via GLP, now my question is how can we connect a Juniper SRX firewall to our core switches?
View 2 RepliesI've just started a new job after a couple of years not touching cisco gear and been pitched in... My new employer has a network that's Juniper based. We've inherited a load of Cisco switches as part of the deal for hosting matches during the Rugby world cup (plus a load of Aruba wireless gear that promises to be my very own special millstone, but that's bye the bye.)
My task is to hang these catalyst 2960's onto our existing infrastructure via fibre connections.
On the Juniper switch, there are four vlans being pushed to the port the cisco's hooked into: Code...
Is there any problems expected in working with core switch of Juniper EX8208 with access switches of Nortel Baystack5520 / 380 / 425 and 325? Whether the VLAN, Multicasting, streaming, STP, SNMP, etc will work without any issues?
View 2 Replies View Relatedhow to convert the CORE 6500 from VSS to non-VSS?
View 2 Replies View Relatedwe need to relocate our core switch 6500 with sup 720 to another bldg
what is the command to gracefully shut it down I mean power off
I was told one can just switch off the power
I have an Issue.In my networks, 1 single user is facing Network Slowness issue. i needs to check to which port user is coneected in switch to CHeck whether that port has any errors.But problem is, i am providing support from remote location.And my concern LAN segment is Very big,I have only user Ip address details,when i ping the Ip address from Core switch it is pinging. but when i give show ip arp & give Ip address then its not learning and listing out the Mac address to trace down to the specific port.
View 3 Replies View RelatedDoing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]
Script:
Backup
sh ver
remote command switch show version
[Code].....
We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies View RelatedI am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.
View 6 Replies View RelatedI am using 6500 with VPN Accelerator on this device. I have a dozen other VPN connections GRE and IPSEC to routers and ASA and other Juniper Firewalls.
They all work perfectly.The error I get is map_db_find_best did not find matching map (Never seen this error be for) [code]I can't put the whole config for security reasons.
If I have two stackable switches one switch uplinks to one 6509 core switch and the other connection uplinks to another 6509 core switch, and also the other stackable switch does not connect to the core switches. Because I am using hsrp and also we are not using vss then one uplink to the core is not in used only ones is so then how does creating an etherchannel between does two uplinks to both core switches benefit me in anyway such as more bandwith and using both uplinks at the same time or I'm I wrong?
View 7 Replies View RelatedIf I have two stackable switches were only one stackable switch has two uplinks one uplink goes to one core 6509 switch and the other uplink goes to the other 6509 core switch can a Layer 3 etherchannel be used if each uplink go to a different core switch, by the way hsrp is running between both switches and also can you give an example how data will be routed from the stackable switch through the ethernetchannel to one of the core switch accross the WAN to another core switch?
View 1 Replies View RelatedI have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies View RelatedWe are using CISCO Catalyst 6500 switches as collapsed core/distribution switches (2 layer architecture). I want to connect approximatly 10 application servers to the network. Can I connect the servers directly to the catalyst 6500 switches using WS-X6148E-GE-TX line cards? The other option is to use access switchs and then connect the servers to the catalyst 6500 through access switch(Catalyst 3750).
View 6 Replies View RelatedIs there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
we are using cisco 6509 series switches as core switches. and Cisco 4510,4507 series switches as edge switches. all the vlans are created at core switches and propogating to edge switches through VTP. we are using OSPF as routing protocol at core switch for internal routing. till now we are using 4510,4507 switches as layer 2 switches. Since, 4510 & 4507 switches are hign end swithces i want use them as layer 3 switches instead of layer 2.if i change these switches from layer 2 to layer 3 does it make any impact on our network or better to keep them as layer 2 switches.if i change these switches to layer 3 is there any advantage i will have.
View 3 Replies View RelatedIn the next couple weekends I'm planning to add 2 CISCO UCS 6248UP Interconnects to 6509 Core Switches via 10G links.
Is there any impact anticipated? It's a production environment and no loss of up-time is acceptable.
I currently have 3 core switches on my campus. They are 6509 catalyst switches. They currently are not interconnected to each other.I want to interconnect them to each other. The IP addresses of each core sit on a interface Loopback500. [code] How can I interconnect each core to each other and what IP scheme could I use. I want them to be straight L3 to each other.
View 8 Replies View Relatedwe have two 6513 core switches redundant to each other by using HSRP and MST. Currently we have a problem in a CPU as it's high in both cores as appeared in the following logging message:
1: 04/09/12 16:06:20 7/-1: MAJ, GOLD,
test_sp_rp_inband_ping[7]: diag_hit_sp_sys_limit. SP-RP Ping Test skipped. Reason(s): netint_thr_active[1].
[Code].....
connecting a 5548 pair to our core 6509s. Just want to be sure we don't introduce any issues into the network.The 6509's are connected and perform all the routing. Essentially, we're moving away from a 3750 stack in the data center and the 5548s are the replacement. We'd want to limit the vlans to the specific server network vlans. Our current setup is a port channel between the 3750 and each of the 2 6509s for redundancy. I'd like to use the same functionality when we connect the 5548's but I'm looking for what the config should look like to ensure no spanning tree loops are introduced and that it is configured optimally.
View 1 Replies View RelatedHow i can view the capacity throughput (backplane) of core switches (6509)? How i know much is in use?
View 2 Replies View RelatedWe have a Cisco 3750G Core switch which has physical connections, each configured as trunks to two HP Access switches. The client who uses these access switches would like to put a link between the two, but this would create a loop.
------- Core Switch -------
| |
| |
[Code]....
The company I work have finally decided to enter the 21st century and invest in a new telephone system (Interactive Intelligence) to replace the legacy system which has served us well for the past 10 years. The project has only just started and involves upgrading sections of CAT3 cabling to CAT6, replacing Cisco 3550 switches in one area of the building with Cisco 4507 switches and upgrading our Core switches with Cisco Nexus 7010's. The area that concerns me most is enabling the network for qos as I have very little experience with it. At the moment Im trying to read as much documentation as I can on QOS to bring myself up to speed.
The access layer switches will consist of a mixture of Cisco 3750 & 4507 switches connected to Cisco Nexus 7010 switches which will form a collapsed aggregation & core layer.
Basically, how I should approach this daunting task of making sure the network will support VOIP.
recommend a cisco core switch and access switches in IPTV network infrastructure?I was ask to implement a network for IPTV system but i don't have idea what will be the model i will use.
Core Switch = Cisco 4503
Access Switches = Cisco 3560X
I configure 3750 stack switch as core and 2960 stack switches as access layer switches.I connected my laptop to one of my core stack in VLAN 10 and I am pinging to one of my server in VLAN 1. What will be the minimum latency at the time of inter VALN routing
View 2 Replies View RelatedI've been fighting what seems to be an increased number of outqueue drops on our core stack and edge switches for the last 3 or 4 weeks.(The core consists of a stack of 5 3750s in 32-gig stack mode. The wkgrp switches are 3560s. all are at 12.2.52) The wkgrp switches are directly connected to users. We use Nortel IP phones with the phone inline with the user PC. auto-neg to 100/full. [code] However I have tried turning off QOS on a couple of workgroup switches (no mls qos, but left individual port configurations the same) but am still seeing drops.Since I have disabled qos on the switches in question (no mls qos) (not the core tho) I am presuming these commands have no affect on the switch operation and therefore cannot be related to the problem. With QOS turned off one would presume that it is general congestion - especially at the user edge where busy PC issues might contribute. So I wanted to see if I could see any instances of packets in the output queues building up.
I wrote some scripts and macros that essentially did a snapshot of 'show int' every 20 seconds or so, and looked for instances of 'Queue: x/' where x was greater than zero.What I found after several days of watching the core stack, and a few of the workgroup switches that are most often displaying the behavior, was that I NEVER saw ANY packets in output queues. I often saw packets in Input queues for VLAN1, once in a great while I would see packets on input queues for fa or Gi interfaces, but NEVER on output queues. [ code] Additionally, when I look (via snmp) at interface utilization on interfaces showing queue drops (both core and wkgroup), they are occurring at ridiculously low utilization levels (as low as 4 to 8%). I've tried to look for microbursts between the core and a wkgroup switch where the core interface was experiencing drops, but haven't seen any (using observer suite). [code] While the queue-drop counts aren't critically high at this point, they are happening more frequently than in the past and I would like to understand what is going on... In most cases, no error counters are incrementing for these interfaces. Is there some mechanism besides congestion that could cause output queue drops?
I have 2 units core swicth C4510R+E SUP7-E need to connect together for redundant purpose , i bought also 4X 10GE uplinks for each core switches .May i know how i shall connect both core switches together using my spec Catalyst 4500 E-Series 12-Port 10GbE (SFP+) ?
View 6 Replies View RelatedI have a stack with 4 2960S and 4 uplinks to the core. I was wondering if it is better to connect one uplink for each switch, or just connect two switches, thus the two members (2&4) not directly connected.
View 1 Replies View RelatedI have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.
View 22 Replies View RelatedI have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.
View 40 Replies View RelatedWe have two 6500 switches and I am unable to login to these switches anymore, but i was able to connect to them yesterday via Telnet. The strange part is that it happened for both switches at the same time.But now when i try to login, it gives me a message "password required, but none set". I can login to them via console.Is it because the 0 - 4 VTY connection are being used and there is no password set from VTY 5 to 15?The config has not changed.
SWITCH-1
line con 0
exec-timeout 0 0
password xxxxx
login
line vty 0 4
[code]....
Two different WAN links get connected to the firewall via two routers.(Different ip subnets).I need to get this two wan streams seperatly to the core switches.Core switches sits.Active/Stanby senario. If the Active core goes down Stndby Core will have take over the traffic. My design is correct ,if not what do i need to change. ASA is 5520.
View 8 Replies View RelatedWe are implementing NAC in our environment and unfortunately still some of our obsolete 6500 switches are running CATOS, the current (cat6000-sup2cvk9.8-6-4.bin) image does not support some of the commands related to NAC implementation. Therefore, I would like to urge you to provide me the 8.7 image which supports all the NAC related commands and will be easier to finish the long pending assignment.
We are in process of replacing the obselete hardware but that will take time.
So, 8.7 K9 CATOS image required.