Cisco Switching/Routing :: Upgrade IOS For Production Core 3750 Switch
May 7, 2013
I want to upgrade IOS for my production core 3750 switch. Below is Show version/fash output. I have IOS image "c3750-ipservicesk9-mz.122-55.SE7", need to confirm below concerns:-
1-As this is stackable switch do i need to upgrade on all Switch..i can see there are 3 flash while doing show flash?
2-Is above IOS image support with my switch? do i able to enable ssh?
3-is flash memory is enough to succefully upgrade IOS?
4-Any other point which i should keep in mind before upgrading..any special feature which this IOS wont support.
View 11 Replies
ADVERTISEMENT
Feb 2, 2013
I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies
View Related
Jun 5, 2013
I am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.
View 6 Replies
View Related
Nov 2, 2011
i am trying to upgrade the software of the core switch 4503e, i could not get the managemenet ip address up and running. what i did is the following :
interfave vlan 1
ip address 192.168.1.1 255.255.255.0
no shu
then my laptop ip address is 192.168.1.100 255.255.255.0?result pinging from CLI is request time out.is there any els command where i need to input ?
View 13 Replies
View Related
Jan 28, 2013
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
View 9 Replies
View Related
Nov 21, 2012
Looking for input/thoughts on the upgrade of our 3560's and 3750's while on production network.
While we could remotely send the IOS over the network to the device, I'm concerned about errors and the lack of physical control of the device. So, the thought is to just go to the comm closet, plug in with laptop to the console port, and upgrade the IOS over the console port. But this would require xmodem, correct? I know the fastest way would be to a. configure an empty fa0/0 port to no switchport, add an IP address, and use tftp. BUT, we would have to isolate the switch from the production network while connected to it with our laptop. Otherwise, our laptop would be seen on the network as an unknown device, and there would be repercussions...
So, we console into the device, and u/l the IOS that way. Is there a way to increase the baud rate on the switch to 115200, change putty to 115200, then do the x modem? I just say we should shut all the ports to isolate the switch from the network, then tftp the IOS to the switch. Unplug, reopen the ports, then reboot the switch.
View 11 Replies
View Related
Nov 20, 2009
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies
View Related
Oct 4, 2012
I have upgraded my 3750X switch from
c3750e-universalk9-mz.122-53.SE3
c3750e-universalk9-mz.122-55.SE5.bin
later that by mistake i typed delete /force /recursive flash:now, I am unable to load new IOS error loading "flash:c3750e-universalk9-mz.122-55.SE5.bin" Interrupt within 5 seconds to abort boot process.Boot process failed...
View 3 Replies
View Related
May 2, 2012
Can we put a module on a 4507R switch running on a live production? The module will come from a 4506 switch.
View 8 Replies
View Related
May 9, 2012
I have a stack of 4 Cisco Switch 3750 (1 x WS-C3750G-24T, 2 x WS-C3750-48P and 1 x WS-C3750V2-48PS) and I want to do an firmware upgrade of this stack. Actually, all the 4 switches are at the firmware version 12.2(50) SE1 "IPBase" and I want to upgrade them to 12.2(55)SE5 IPBase. According to the release notes, all the switches in my stack are supported.
To upgrade the firmware, I use the command "archive download-sw /imageonly /overwrite tftp://IP_Address/c3750-ipbaselmk9-tar.122-55.SE5.tar" The firmware gets uploaded correctly but then I get the error message "There is insufficient space in flash: to install the required image. Clean up some old images, and try again."
When I do a "show flash", I see that the switch has 5650944 bytes free of 15998976 bytes.
How can i upgrade my switches? Is there an error in my command which I use? Do I need to add an other option?
The problem is, the switches are located in a branch office and there is no direct access to them. Everything must be done remotely.
View 3 Replies
View Related
Apr 29, 2012
Doing a bug scrub on our dual core, dual Sup 720 6500s tonight. We are going from s72033-advipservicesk9_wan-mz.122-33.SXI4a.bin to SXI9. I want to get a second set of eyes on my script since I have not done this for about 1 1/2 years. Following this doc:[URL]
Script:
Backup
sh ver
remote command switch show version
[Code].....
View 6 Replies
View Related
Nov 23, 2011
As we know there are three layer in cisco Network Model:
-Core
-Distribution
-Access
So my question is in Core / Distribution layer should i use Etherchannel between switches or use Stacking if switches are stackble.For ex: suppose I have two cisco 3750 switches . so should i use etherchannel between them or use stacking in core layer?What are the advantages and disadv of both.
View 5 Replies
View Related
Jun 19, 2012
I'm working designing a switch system for our core/data center.
We have 5 esx hosts, 2 sans with 3 nodes each. We have voice servers, a couple of routers and a few odds and ends. There are 7 other locations aggregating into this data center via 1-2gbps fiber connections. The bandwidth usage on these links is minimal, but there is a total of about 3000 devices aggregating into the system. My main concern right now is the 3560G's are seeing many output drops, due to the small buffer size on those switches. I have been looking at couple of options to resolve this issue, including the 4948E, 4507E, and 3750X switches.
Budget being the biggest factor, I am finding that the 4507 might be out of the price range. So I was leaning towards the 4948E switches for connecting the servers and iscsi san's as the 3750X is not recommended for iscsi. Redundancy is important so I would like to have two. The second concern is that I need to aggregate the fiber connections and for that I was looking at the ME-3600X or possibly the WS-C3750X-12S-E. I'm running eigrp, so this switch would need to have full routing, as it would also serve as the core switch for the 4948E's.
So in the end I was thinking that two 4948E switches up linked to the ME-3600X which would do full routing for the fiber aggregation and any routing needed for the servers and sans.
Servers and Sans_________4948E________ME-3600X_________7 fiber connections
|____________4948E_____________|
I would look at a second ME-3600X in the future for redundancy. This is the lowest cost biggest buffer solution that I could find.
View 2 Replies
View Related
Feb 8, 2012
The company I work have finally decided to enter the 21st century and invest in a new telephone system (Interactive Intelligence) to replace the legacy system which has served us well for the past 10 years. The project has only just started and involves upgrading sections of CAT3 cabling to CAT6, replacing Cisco 3550 switches in one area of the building with Cisco 4507 switches and upgrading our Core switches with Cisco Nexus 7010's. The area that concerns me most is enabling the network for qos as I have very little experience with it. At the moment Im trying to read as much documentation as I can on QOS to bring myself up to speed.
The access layer switches will consist of a mixture of Cisco 3750 & 4507 switches connected to Cisco Nexus 7010 switches which will form a collapsed aggregation & core layer.
Basically, how I should approach this daunting task of making sure the network will support VOIP.
View 6 Replies
View Related
Sep 29, 2012
I configure 3750 stack switch as core and 2960 stack switches as access layer switches.I connected my laptop to one of my core stack in VLAN 10 and I am pinging to one of my server in VLAN 1. What will be the minimum latency at the time of inter VALN routing
View 2 Replies
View Related
Jan 10, 2013
I've been fighting what seems to be an increased number of outqueue drops on our core stack and edge switches for the last 3 or 4 weeks.(The core consists of a stack of 5 3750s in 32-gig stack mode. The wkgrp switches are 3560s. all are at 12.2.52) The wkgrp switches are directly connected to users. We use Nortel IP phones with the phone inline with the user PC. auto-neg to 100/full. [code] However I have tried turning off QOS on a couple of workgroup switches (no mls qos, but left individual port configurations the same) but am still seeing drops.Since I have disabled qos on the switches in question (no mls qos) (not the core tho) I am presuming these commands have no affect on the switch operation and therefore cannot be related to the problem. With QOS turned off one would presume that it is general congestion - especially at the user edge where busy PC issues might contribute. So I wanted to see if I could see any instances of packets in the output queues building up.
I wrote some scripts and macros that essentially did a snapshot of 'show int' every 20 seconds or so, and looked for instances of 'Queue: x/' where x was greater than zero.What I found after several days of watching the core stack, and a few of the workgroup switches that are most often displaying the behavior, was that I NEVER saw ANY packets in output queues. I often saw packets in Input queues for VLAN1, once in a great while I would see packets on input queues for fa or Gi interfaces, but NEVER on output queues. [ code] Additionally, when I look (via snmp) at interface utilization on interfaces showing queue drops (both core and wkgroup), they are occurring at ridiculously low utilization levels (as low as 4 to 8%). I've tried to look for microbursts between the core and a wkgroup switch where the core interface was experiencing drops, but haven't seen any (using observer suite). [code] While the queue-drop counts aren't critically high at this point, they are happening more frequently than in the past and I would like to understand what is going on... In most cases, no error counters are incrementing for these interfaces. Is there some mechanism besides congestion that could cause output queue drops?
View 4 Replies
View Related
May 31, 2012
we need to relocate our core switch 6500 with sup 720 to another bldg
what is the command to gracefully shut it down I mean power off
I was told one can just switch off the power
View 4 Replies
View Related
Jun 2, 2013
i configure the uplinks as etherchannel, i configure two svi interface on core switch int vlan 51(192.168.51.1) and int vlan 50(192.168.50.0) for this two svi int i configured two dhcp pool , when any of the pc is requesting for dhcp add i am getting dhcp request failed/
View 7 Replies
View Related
Jun 7, 2012
I'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.
View 3 Replies
View Related
Nov 4, 2012
I have 2 units core swicth C4510R+E SUP7-E need to connect together for redundant purpose , i bought also 4X 10GE uplinks for each core switches .May i know how i shall connect both core switches together using my spec Catalyst 4500 E-Series 12-Port 10GbE (SFP+) ?
View 6 Replies
View Related
Dec 20, 2011
I am experiencing high cpu utilization in my 4000 series core switch.
I checked the loggs. i saw some strange loggs.
Please see the below logs:
Code...
What is the "invalidsourceaddresspacket" ?
Is this is due to some virus attack or something?? Also one more thing this switch is the Active router in HSRP.
View 12 Replies
View Related
Sep 21, 2012
I have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.
View 40 Replies
View Related
Oct 14, 2012
We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies
View Related
Apr 13, 2013
I have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.
View 22 Replies
View Related
Aug 30, 2012
choosing a core switch, to replace a swich 3com model 4924, its main function is to support a 4-LAN switch cisco 2960 (100 users) and a ring cluster of 12 servers.obs. Current 3com core switch has 56 Gbps performance and 41.6 million packets per second.
View 3 Replies
View Related
Feb 14, 2012
We had a core switch(30 vlans) in our environment and it's noticed that CPU utilization of the core switch is showing high during recent days. I have checked logs and processes, but couldn't find the root cause. The issue found only in the office hourly only(after that the cpu utilization is idle and normal). I have already referred the following link to troubleshoot the issue " [URL]
see the following outputs from the core switch
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 6687557041432420936 466 47.52% 47.10% 45.98% 0 Cat4k Mgmt LoPri
55 30667074884269560256 0 45.36% 45.50% 45.85% 0 IP Input
29 28552856922870089254 0 3.59% 3.50% 3.57% 0 Cat4k Mgmt HiPri
[code]....
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
My queries regarding the issues are following
1) How can we find root cause regarding the high cpu utilization?
2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?
View 10 Replies
View Related
Nov 18, 2012
Two Cisco 3750X can be stacked together to ensure redundancy.Is the attached topology feasible for access layer redundancy?
View 5 Replies
View Related
Jan 13, 2012
We have two core switches in our network (Cisco WS-4503). HSRP is working as Active-Standby mode. Recently it has been found that core 1 (which is in active mode) shown high CPU load (60% - 100%). Also found that the below mentioned process takes more CPU. Our network consist of around 30 Vlans. We have already checked for the solution in Cisco website [URL] but couldn't find exact reason. see the below outputs for core 1 switch.
Core1# sh processes cpu sorted
CPU utilization for five seconds: 55%/3%; one minute: 65%; five minutes: 71%PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 30 1606933521086983644 147 24.79% 29.93% 35.85% 0 Cat4k Mgmt LoPri 29
[Code]....
View 3 Replies
View Related
Sep 16, 2012
I have the following: 1 5520 ASA connected to the internet, 2 core switches, and several access switches.Aside from implementing RSTP, VRRP, hard code access and trunk ports, is there any other recommendation you would like to add.
View 7 Replies
View Related
Jun 25, 2011
I am doing an evaluation of LMS 4.0. I have loaded the system on Windows and manually added my core 3750 switch into the system. Device availability is showing the device as available. However, the other pollers like link utilization, error count, etc. all show that there is no data. When I go into the poller config, the pollers for link utilization and errors show 0 devices associated and a status of "instance not found". The CPU and availability pollers show active with my one device added. I have verified the credentials and if I go into Inventory -> Port and module and select my 3750 I do get a list of all the interfaces and the descriptions so LMS is connecting to the switch and pulling data.
So how do I get the pollers for link utilization and errors to start populating data?
Second question, during install I did configure the software update section and it said there was an LMS 4.0.1 available which I told it to download. Now I have a psu_download directory and some more directories like cm, cmf, etc. but I don't see any file on what to do with them. What do I need to do to install the new package files that were downlaoded to psu_download?
View 4 Replies
View Related
Jan 25, 2012
i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
View 6 Replies
View Related
Oct 6, 2012
To setup SG300-20 as CORE switch and SF100-48 as Distribution switch.SG300-20 will have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 DATA
-172.168.0.1/24 VOICE
SF100-48 will also have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 Desktop/Laptops
-172.168.0.1/24 IP phones
Problem is when I tried to assign IP to any VLAN's the switch will just hang and loose my connection the light will stop blinking it will steady and i unable to access the switch until i turn off again?
View 1 Replies
View Related
Oct 23, 2011
What is PIM? give me an example when I will use and not use the PIM command.
View 4 Replies
View Related
