Cisco Switching/Routing :: Setup SG300-20 As Core And SF100-48 As Distribution Switch

Oct 6, 2012

To setup SG300-20 as CORE switch and SF100-48 as Distribution switch.SG300-20 will have 2 VLAN(DATA and VOICE)
 
-192.168.14.1/24 DATA
-172.168.0.1/24 VOICE
 
SF100-48 will also have 2 VLAN(DATA and VOICE)
 
-192.168.14.1/24 Desktop/Laptops
-172.168.0.1/24 IP phones
 
Problem is when I tried to assign IP to any VLAN's the switch will just hang and loose my connection the light will stop blinking it will steady and i unable to access the switch until i turn off again?

View 1 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Nexus 7000 As Collapsed Core / Distribution?

Apr 9, 2013

I had a lot of questions when I began planning a pair of Nexus 7000 switches as a replacement for our 6500. How to publish my design and config. This is a medium sized network. I would have loved to see somone's configs for a similar implementation.

[URL]...

View 5 Replies View Related

Cisco :: Can't Have Multiple Links From Each Access Layer Switch To Core / Distribution

Jan 24, 2013

I have been working on redesign of our network which was very challenging but almost there.We have a limited budget of around £20k(32k Dollor) Max. The cabling has been done before my time and it is very messy and cheap so you can not do a proper cisco hierarchical model at all.I can not have multiple links from each access layer switch to the core/distribution and as a result i had to connect some access switches together to introduces redundancy in a nutshell,we have two buildings, main building which has the server room in it and the other building which is just bunch of office. i have introduced a partial mesh on the normal building and have tried to introduce full mesh on the main building .

View 9 Replies View Related

Cisco Switching/Routing :: How To Enable Ssh On 4507 Distribution Switch

Jan 30, 2013

We have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin

View 1 Replies View Related

Cisco Switching/Routing :: 3750G / Switch Loses Connecting To Distribution SW

Feb 21, 2013

The two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Power Off Core Switch?

May 31, 2012

we need to relocate our core switch 6500 with sup 720 to another bldg
 
what is the command to gracefully shut it down I mean power off
 
I was told one can just switch off the power

View 4 Replies View Related

Cisco Switching/Routing :: How To Configure 1 Core Switch 4500

Jun 2, 2013

i configure the uplinks as etherchannel, i configure two svi interface on core switch int vlan 51(192.168.51.1) and int vlan 50(192.168.50.0) for this two svi int i configured two dhcp pool , when any of the pc is requesting for dhcp add i am getting dhcp request failed/

View 7 Replies View Related

Cisco Switching/Routing :: 2960G Core Switch For 400 Users

Jun 7, 2012

I'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.

View 3 Replies View Related

Cisco Switching/Routing :: How To Connect Two Core Switch C4510R+E SUP 7-E

Nov 4, 2012

I have 2 units core swicth C4510R+E SUP7-E  need to connect together for redundant purpose , i bought also 4X 10GE uplinks for each core switches .May i know how i shall connect both core switches together using my spec Catalyst 4500 E-Series 12-Port 10GbE (SFP+) ?

View 6 Replies View Related

Cisco WAN :: 6500 - Connecting Servers To Core / Distribution Switches

Feb 10, 2013

We are using CISCO Catalyst 6500 switches as collapsed core/distribution switches (2 layer architecture). I want to connect approximatly 10 application servers to the network. Can I connect the servers directly to the catalyst 6500 switches using WS-X6148E-GE-TX line cards? The other option is to use access switchs and then connect the servers to the catalyst 6500 through access switch(Catalyst 3750).

View 6 Replies View Related

Cisco Switching/Routing :: EWA14 - High CPU Utilization In Core Switch

Dec 20, 2011

I am experiencing high cpu utilization in my 4000 series core switch.
 
I checked the loggs. i saw some strange loggs.
 
Please see the below logs:

Code...

What is the "invalidsourceaddresspacket" ?
 
Is this is due to some virus attack or something?? Also one more thing this switch is the Active router in HSRP.

View 12 Replies View Related

Cisco Switching/Routing :: 2960S Unable To Connect To Core Switch

Sep 21, 2012

I have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.

View 40 Replies View Related

Cisco Switching/Routing :: 6500 - Changing VTP Mode Of A Core Switch

Oct 14, 2012

We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.

View 7 Replies View Related

Cisco Switching/Routing :: Connecting Core Switch To Firewall 3750x

Apr 13, 2013

I have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.

View 22 Replies View Related

Cisco Switching/Routing :: Migrating Core Switch From 3750 To 6500?

Jun 5, 2013

I am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.

View 6 Replies View Related

Cisco Switching/Routing :: Change From 3com Core Switch By 2960?

Aug 30, 2012

choosing a core switch, to replace a swich 3com model 4924, its main function is to support a 4-LAN switch cisco 2960 (100 users) and a ring cluster of 12 servers.obs. Current 3com core switch has 56 Gbps performance and 41.6 million packets per second.

View 3 Replies View Related

Cisco Switching/Routing :: Upgrade Software Of Core Switch 4503e?

Nov 2, 2011

i am trying to upgrade the software of the core switch 4503e, i could not get the managemenet ip address up and running. what i did is the following :
 
interfave vlan 1
ip address 192.168.1.1 255.255.255.0
no shu
  
then my laptop ip address is 192.168.1.100 255.255.255.0?result pinging from CLI is request time out.is there any els command where i need to input ?

View 13 Replies View Related

Cisco Switching/Routing :: Very High CPU Utilization Core Switch 4503?

Feb 14, 2012

We  had a core switch(30 vlans) in our environment and it's noticed that  CPU utilization of the core switch is showing high during recent days. I  have checked logs and processes, but couldn't find the root cause. The  issue found only in the office hourly only(after that the cpu  utilization is idle and normal). I have already referred the following  link to troubleshoot the issue " [URL]
 
see the following outputs from the core switch
 
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms)   Invoked      uSecs   5Sec   1Min   5Min TTY Process
  30   6687557041432420936        466 47.52% 47.10% 45.98%   0 Cat4k Mgmt LoPri
  55  30667074884269560256          0 45.36% 45.50% 45.85%   0 IP Input
  29  28552856922870089254          0  3.59%  3.50%  3.57%   0 Cat4k Mgmt HiPri

[code]....
 
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
  
My queries regarding the issues are following
 
1) How can we find root cause regarding the high cpu utilization?

2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?

View 10 Replies View Related

Cisco Switching/Routing :: Upgrade IOS For Production Core 3750 Switch

May 7, 2013

I want to upgrade IOS for my production core 3750 switch. Below is Show version/fash output. I have IOS image "c3750-ipservicesk9-mz.122-55.SE7", need to confirm below concerns:-
 
1-As this is stackable switch do i need to upgrade on all Switch..i can see there are 3 flash while doing show flash?
2-Is above IOS image support with  my switch? do i able to enable ssh?
3-is flash memory is enough to succefully upgrade IOS?
4-Any other point which i should keep in mind before upgrading..any special feature which this IOS wont support.

View 11 Replies View Related

Cisco Switching/Routing :: 3750X / Core Switch In Redundant Mode?

Nov 18, 2012

Two Cisco 3750X can be stacked together to ensure redundancy.Is the attached topology feasible for access layer redundancy?

View 5 Replies View Related

Cisco Switching/Routing :: WS-4503 - Core Switch Having High CPU Load

Jan 13, 2012

We have two core switches in our network (Cisco WS-4503). HSRP is working as Active-Standby mode. Recently it has been found that core 1 (which is in active mode) shown high CPU load (60% - 100%). Also found that the below mentioned process takes more CPU. Our network consist of around 30 Vlans. We have already checked for the solution in Cisco website [URL]  but couldn't find exact reason. see the below outputs for core 1 switch.
 
Core1# sh processes cpu sorted
CPU utilization for five seconds: 55%/3%; one minute: 65%; five minutes: 71%PID Runtime(ms)   Invoked      uSecs   5Sec   1Min   5Min TTY Process  30   1606933521086983644        147 24.79% 29.93% 35.85%   0 Cat4k Mgmt LoPri  29 

[Code]....

View 3 Replies View Related

Cisco Switching/Routing :: 5520 Dual Core Switch For Redundancy

Sep 16, 2012

I have the following: 1 5520 ASA connected to the internet, 2 core switches, and several access switches.Aside from implementing RSTP, VRRP, hard code access and trunk ports, is there any other recommendation you would like to add.

View 7 Replies View Related

Cisco Switching/Routing :: 2 Internet Connection Connected To Same Core Switch 6509

Jan 25, 2012

i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
 
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
 
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
 
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
 
is it ok if i make another default route to the Next hop to the new DSL router as:
 
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
 
10.80.10.10 is --> Next hop for the new DSL router internal IP.

View 6 Replies View Related

Cisco Switching/Routing :: 3750 / 6509 - Upgrade Core Switch Without Disrupting Network?

Feb 2, 2013

I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.

View 7 Replies View Related

Cisco Switching/Routing :: 6509 Core Switch Command / IP PIM Sparse-dense-mode

Oct 23, 2011

What is PIM? give me an example when I will use and not use the PIM command.

View 4 Replies View Related

Cisco Switching/Routing :: Not Logging All Levels Of Sylog Messages From Core Switch 4503

Apr 23, 2012

We had a core switch(4503) in our environment and recently we tried to enable syslog in the switch. But the syslog server doesnt receives all the configured level messages from the switch. Following is the only message getting in syslog server after the configuration change in switch.
 
%SYS-5-CONFIG_I: Configured from console by CWLMS onvty1
 
(No Traffic related messages like acl deny traffic, spanning tree events etc are getting to syslog server as well as log buffer of the switch)
 
Following are the logging configuration for the core switch
 
logging monitor informational
logging facility syslog
logging source-interface Vlan44

[Code]....

1) Is there any more configurations required for getting all traffic related messages, (i mean all possible messages - upto level 7 - debugging)?

View 3 Replies View Related

Cisco Switching/Routing :: SG300 Network Setup For Voice And Other VLANs?

Mar 18, 2013

I have spent several days tearing my hair out trying to properly configure our small business switch (SG300-10p) for voice. The phones are a relatively new addition and will replace old POTS phones.Our network consists of a 1941 ISR router, the SG300-10P switch, a mac server (handing DHCP, DNS, AFP), 4 client desktops and 4 SGA525G2 IP phones. The router, server, desktops and phones all have their own connection to the switch and the second data ports on the back of the IP phones are not used. We do not have any unified comms devices for voice. Our VOIP solution is hosted by a local SIP provider, and each phone independently registers with the provider's SIP proxy over the internet.

Left almost to it’s own devices (or presumably flat, default settings on VLAN 1), this whole setup works just great. We can TFTP files, make and receive calls, and do all the usual XML stuff. Calls are crystal clear. Even the localisation and directory works. However, I’ve been told several times that to ensure good quality on VOIP calls during periods of busy traffic, I should set up some form of QoS. A Voice VLAN on the switch, I was told, is the best way to do this as it automagically gives priority to the whole voice VLAN over the normal data VLAN.

I have followed instructions in numerous manuals, articles and guides, and have managed to create the Voice VLAN, both manually and automatically (I can watch Smartport detect the phones and see the Auto Voice VLAN add the ports to the VLAN as I connect them). The trouble is, as soon as this happens, the phones lose connectivity with the rest of the network, including the DNS server and the router, and therefore the internet, causing them to lose registration with the SIP service.

I tried adding the server and router ports to the Voice VLAN and tweaking every possible combination of tagged, untagged, excluded, trunk, access, general and PVID settings I can think of (by the way, I have no idea what any of those mean). The switch is in Layer 2 mode, but adding the port connected to the router to all the VLANs does not result in internet connectivity to the phones. I have told the phones to tag frames with the VLAN ID and told them not to. I have tried upgrading firmware and I have rebooted the switch so many times I'm tired of those wretched little flashing lights.
 
Nothing seems to work. And so I am stuck with everything on VLAN 1. My most recent thought is that the 1941 needs to know about the Voice VLAN (I checked CDP and it knows about the switch), but I’m reluctant to start messing with the router config when this is our production network, at least without knowing what I'm doing. I don’t even know if QoS applies when a Voice VLAN is not set up and we're on VLAN 1, some articles say yes, others say no. And when it is set up right, how does that priority transfer to the router? I’ve looked in the router manual and config options and found something called 802.1Q, but I have no idea what it is, how it works or even if it applies to our situation. Can I forgo VLANs altogether and use QoS some other way, perhaps?I have googled enough to cobble together our setup in IOS up until now. Ideally, I would still like to be able to ssh or https into each device (as I do now) for management, and I’ve read about setting up a another VLAN for config, monitoring etc, but I guess that would mean routing between VLANs in Layer 3.

View 2 Replies View Related

Cisco Switching/Routing :: SG300 - Vlan Setup Automatically Changing?

Jul 9, 2012

I have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
 
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
 
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?                  
 
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.

View 1 Replies View Related

Cisco Switching/Routing :: Inter-VLAN Routing Using 877 And SG300-10 Switch

Feb 5, 2012

I recently set up a small photography business and am trying to get a Cisco 877 and Cisco SG300-10 switch to talk to each other.
 
What I want is for the Cisco 877 to handle the internet and the SG300-10 to handle the local network,
 
I have set up 2 vlans in trunk mode on the switch and want vlan2 to manage local traffic and vlan3 to handle the internet.
 
I have got the 877 connecting to the internet what I dont have, traffic going to vlan2 on the switch from the 877
 
Look at the running configs for the switch and the router and tell me how to get the vlan on the router to pass traffic to the switch. In a nutshell I am inserting the internet into the switch but am not sure how to progress. I have the c870-advipservicesk9 image file on the router. 

Switch Config
 
interface  gi2
description connection-to-data-vlan
exit
interface  gi3
description connection-to-internet-vlan
exit
vlan database (code )

View 11 Replies View Related

Cisco Switching/Routing :: Limit For Creation Of Port Chanel In Core Switch 6509 And 6513

Feb 20, 2012

How much is the limit for the creation of PortChanel in a Core Switch 6509 and 6513?Is there a limitation byu hardware?

View 7 Replies View Related

Cisco Switching/Routing :: SG300-10P Power SG200-08 Switch Over POE?

Jun 1, 2012

Can a Cisco SG300-10P switch power a Cisco SG200-08 switch over POE?  Or an SG200-08P power an SG200-08 via POE?  I have an area where I'd like to put a small switch, but would like to avoid having to have electrical power run to it.  Or will the SG300 and SG200 POE switches only power endpoint devices such as cameras and IP phones?

View 4 Replies View Related

Cisco Switching/Routing :: 6500 Ping Packet Drop From Core-Switch To Directly Connected Server

Oct 24, 2011

I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.

View 9 Replies View Related

Cisco Switches :: SF100 24 Switch Come With Brackets To Rack Mounted

Jul 26, 2012

Simple question, does the SF100-24 switch come with the brackets to rack mount it on a standard 19" rack?

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved