Cisco Switching/Routing :: Limit For Creation Of Port Chanel In Core Switch 6509 And 6513
Feb 20, 2012How much is the limit for the creation of PortChanel in a Core Switch 6509 and 6513?Is there a limitation byu hardware?
View 7 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2 Internet Connection Connected To Same Core Switch 6509
Jan 25, 2012i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
Cisco Switching/Routing :: Impact Of Deleting And Creation Of SVI Interface On PBR 6513
Apr 22, 2013I have a query regarding the deletion and creation of one of my SVI interface on 6513 ,The reason behind it as follows.My traffic get to Internet in this manner
proxy(external int.)[IP:192.168.1.30] --> Gi0/9[6513 in VLAN 170] --> SVI VLAN 170[IP:192.168.1.10] --> Gi0/10[In VLAN 170] -->ASR[IP:192.168.1.20],I need to assign this VLAN ie 170 to my inside interface of firewall but it was mentioned in books like this "Assign the VLAN for the FWSM before it is applied to the MultilayerSwitch Feature Card (MSFC)." so I am thinking the following steps to assign VLAN 170 to firewall group first before creating SVI Interface for it
1.Remove all currently assign ie Gi 0/9 & Gi0/10 interfaces from this VLAN and then delete this VLAN.
2.Create the same SVI ie VLAN 170[IP:192.168.1.10] by this way the issue can be resolved.
As in part of my configuration PBR is define like this .
interface Vlan170
description "PUBLIC IP VLAN"
ip address 192.168.1.20. 255.255.255.0
ip policy route-map NAT
route-map NAT permit 10
match ip address 101
set ip next-hop 192.168.1.10
I need to clearify what impact it may have on PBR part if I delete and create the VLAN 170.Will the traffic move to the inside interface of FWSM.
Cisco Switching/Routing :: 3750 / 6509 - Upgrade Core Switch Without Disrupting Network?
Feb 2, 2013I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies View RelatedCisco Switching/Routing :: 6509 Core Switch Command / IP PIM Sparse-dense-mode
Oct 23, 2011What is PIM? give me an example when I will use and not use the PIM command.
View 4 Replies View RelatedCisco Switching/Routing :: Configuring Span Port On 6513 Switch
Mar 2, 2012I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
How to configure span port.
switch 6513-1# show run int Gi10/43 --------------------Server 1 is connected
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.
Cisco Switching/Routing :: High CPU Utilization In 6513 Core Switches
Apr 8, 2012we have two 6513 core switches redundant to each other by using HSRP and MST. Currently we have a problem in a CPU as it's high in both cores as appeared in the following logging message:
1: 04/09/12 16:06:20 7/-1: MAJ, GOLD,
test_sp_rp_inband_ping[7]: diag_hit_sp_sys_limit. SP-RP Ping Test skipped. Reason(s): netint_thr_active[1].
[Code].....
Cisco Switching/Routing :: 3750x Switch Port Rate Limit
Oct 8, 2012I want to limit the bandwidth going to remote site on the switch connecting to our netapp.We have a 4 port channel group setup on our 3750x switch going to our netapp storage. We have a Wan 100mb link to our remote site and we want only 60MBs of that link to be used for Netapp traffic all other local traffic needs to use the full amount of the bandwidth to the netapp.
Is possible to allocate bandwidth in this way and how would I go about this? We dont have access to the routers for the link and they plug directly into a port on our cisco.
Cisco Switching/Routing :: How To Limit Broadcast Traffic On 3560 Switch Port
Dec 17, 2012How do I limit broadcast/mulitcast traffic on a switchport to e.g. 5000 pps ? I don't want the port to shut down, just block or drop broadcast traffic that exceeds 5000 pps.
View 19 Replies View RelatedCisco Switching/Routing :: Catalyst 2960 Switch Port Bandwidth Limit?
Sep 18, 2012I want to configure switch port bandwidth limit for my Catalyst 2960-48, is there any hardware / ios limitation? can I configure it at all 48 switch ports?
View 1 Replies View RelatedCisco Switching/Routing :: Limit Bandwidth On A Gig Port Of 2960 Or 4506e Switch?
Apr 4, 2012how can i limit bandwidth on a gig port of 2960 or 4506e switch?
View 9 Replies View RelatedCisco Switching/Routing :: 6513 Span Session Limit?
Jul 12, 2012I have a need to capture some traffic but my core 6513's are already using the limit of 2 span sessions. I can't edit any of the sessions either because I want to source traffic from vlans and you can only do one or the other. Is using a VACL with 'switchport capture' on the destination interface an option ? E.g. I want to source traffic from vlan 10,20,30,40 and send the all to interface Gi10/10 ? Is there any caveats ? I dont need to be too granular with the ACL's but just capture all traffic in those vlans.
View 2 Replies View RelatedCisco Switching/Routing :: 6513 - Rate Limit And Traffic Shaping?
Mar 21, 2012I am looking for step-by-step configuration on how to enable rate-limit and traffic shaping on Cisco 6513 vlan interfaces. I am not able to find this particular document on CCO.
View 3 Replies View RelatedCisco Switching/Routing :: 6513 / 6509 E - EOL Notices
Apr 18, 2013Are there any EOL notices out for the Catalyst 6513, 6509 etc E chassis? I cant find anything on the internet for the E variant, so assume this hasn't had a notice published yet.
View 2 Replies View RelatedCisco Switching/Routing :: 6509 To 6513 Migration Required
Jan 9, 2012We currently run 1 Cisco 6509 (CatOS) for our production network. It has multiple vlans which feed distribution switches on each floor in 2 buildings. Essentially each floor is its own vlan. Each floor switch is connected back to the 6509 via fiber connections. We also have several production vlans that our VMware and AIX environments connect to.
I would like to phase out the the 6509 and replace it with a new 6513 chassis, sup720's etc. Currently it is sitting next to the 6509 in the rack. I need to limit downtime as much as possible but can get one shutdown window over a weekend. However I dont think it would be enough time to move all of the existing etherconnections etc etc
So I am looking to run them both at the same time and slowly migrate over to the 6513 over the next few months.My solution was to use the 6513 (IOS) in L2 mode only for now and trunk it back to the 6509 via 4 1 gig connections in a LACP config.
So the 6509 would still be handling all of the L3 routing for now.Once I had moved all of the fiber and ethernet connections over to the 6513, I would use the shutdown weekend to configure the 6513 for L3 and essentially turn off the 6509 at that point.
My questions are
- Is there a better way to do this ?
- By trunking the 6513 to the 6509 do I need to worry about any loop issues ?
- I am aware of the oversubscription issue for the port channel and have spread the 4 interfaces over the different groups of asics.
Cisco Switching/Routing :: Run VSS On 6513 / 6509 Considering Both Has Same Supervisor Engine 2T And IOS Image
Jun 25, 2012Is it possible to run VSS on 6513 and 6509 when considering both has same supervisor engine 2T and same IOS image.
View 1 Replies View RelatedCisco Switching/Routing :: Using 6509 Series As Core Switches
Jun 2, 2012we are using cisco 6509 series switches as core switches. and Cisco 4510,4507 series switches as edge switches. all the vlans are created at core switches and propogating to edge switches through VTP. we are using OSPF as routing protocol at core switch for internal routing. till now we are using 4510,4507 switches as layer 2 switches. Since, 4510 & 4507 switches are hign end swithces i want use them as layer 3 switches instead of layer 2.if i change these switches from layer 2 to layer 3 does it make any impact on our network or better to keep them as layer 2 switches.if i change these switches to layer 3 is there any advantage i will have.
View 3 Replies View RelatedCisco Switching/Routing :: 6509 VSS Implementation As A Service Module Core
Jun 8, 2011I m planning to implement VSS in core but want some inputs on IOS as i have FWSM as a service module Core :- Ii am running 12.2(33)SXH2a on my Core 6509 and i checkd cisco sites and Fwsm release notes but it states only I-Train of IOS while mine is H-Train so can I directly upgrade to I-Train or I was thinking of SXH8b IOS.
View 2 Replies View RelatedCisco Switching/Routing :: Adding UCS 6248UP To 6509 Core Switches?
Apr 21, 2013In the next couple weekends I'm planning to add 2 CISCO UCS 6248UP Interconnects to 6509 Core Switches via 10G links.
Is there any impact anticipated? It's a production environment and no loss of up-time is acceptable.
Cisco Switching/Routing :: Connecting 5548 Pair To 2 6509 Core Switches / No Vss
Jun 8, 2012connecting a 5548 pair to our core 6509s. Just want to be sure we don't introduce any issues into the network.The 6509's are connected and perform all the routing. Essentially, we're moving away from a 3750 stack in the data center and the 5548s are the replacement. We'd want to limit the vlans to the specific server network vlans. Our current setup is a port channel between the 3750 and each of the 2 6509s for redundancy. I'd like to use the same functionality when we connect the 5548's but I'm looking for what the config should look like to ensure no spanning tree loops are introduced and that it is configured optimally.
View 1 Replies View RelatedCisco Switching/Routing :: View Capacity Throughput (backplane) Of Core Switches (6509)?
May 30, 2012How i can view the capacity throughput (backplane) of core switches (6509)? How i know much is in use?
View 2 Replies View RelatedCisco Switching/Routing :: 6509 - IP Multicast Rate Limit
Nov 26, 2012How is it i can implement the command 'ip multicast rate-limit out group-list <access-list>' but i get the error "ip multicast rate-limit" command is not supported on 6509?
Is it an IOS limitation or a limitation of the switch series and subsequently can't be used at all?
Cisco Switching/Routing :: 6509-E - Rate Limit PPS On Interface?
Jun 8, 2013How (and is) it possible to rate limit pps on an interface (physical/logical), on a 6509-E?The porpuse is to protect from attacks which lead to very high pps, bypassing traffic rate-limits, and effecting the device's performance
View 2 Replies View RelatedCisco WAN :: 6509 - MAC Address Flapping In Core Switch
Dec 28, 2010I am getting following error in Cisco 6509 switch.BUt there is no impact in the switch.
: %MAC_MOVE-SP-4-NOTIF: Host 0000.0c07.ac01 in vlan 694 is flapping between port Te8/1 and port Te7/1
29:33.959: %MAC_MOVE-SP-4-NOTIF: Host 0000.0c07.ac01 in vlan 269 is flapping between port Te7/1 and port Te8/1
[Code].....
Cisco WAN :: VPC Configuration Template With Two Core 6509 Switch
Jan 3, 2013What is the VPC configuration template with two core 6509 switch.Pls find the attachment for Network topology.
View 3 Replies View RelatedCisco Switching/Routing :: 6509 QOS To Limit Bandwidth For Internet Traffic
Nov 5, 2012We run a workers camp here and we currently have around 2500-3000 people using our 100MB internet pipe. We are upgrading the pipe to 200MB soon but I still would like to limit how much bandwidth everyone is using.
We allow streaming media such as Netflix, youtube, apple TV and of course .So it gets full pretty fast. We have QOS implemented although I wasn't here when it was done so I don't know a lot about it. I would like to limit IPs to a certain amount of bandwidth. [code]
Cisco Firewall :: 6509 Core Switch - How To Create DMZ Vlan
Oct 31, 2012I need to create a DMZ Vlan. Core switch is a 6509. FW is an ASA5520. Need to create a VLAN for DMZ purposes for outside facing servers. NAT is used on ASA.
View 7 Replies View RelatedCisco :: Core Switch 6509 - Route Each Vlan To Exit From Spacific DSL
Jan 26, 2012i'm already has one internet connection is connecting directly to the Core Switch 6509,Vlan 500 (1921.168.1.0) and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
The Problem: We have a new internet connection with new Vlan 600 (172.16.1.0) another ISP/ with another DSL router, so i need your kindly support and suggest how to connect both of them to exit from the Core Switch 6509. is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
is there any way like default route , route-map or any other features to :
route Vlan 500 (192.168.1.0) to exit from DSL 1 --> 10.170.10.10
route Vlan 600 (172.16.1.0) to exit from DSL 2 --> 10.80.10.10
Cisco Switching/Routing :: Module Power Down On 6513 Switch?
Apr 28, 2012We have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".
View 4 Replies View RelatedCisco Switching/Routing :: 6513 - Switch To SP Mode After Reboot
Mar 20, 2013Need your expert input in sorting out the below problem.I have a cisco 6513 switch which is going into SP mode after a reboot whci i have done during BCP activity in my organization.Below are the log for your reference.
Code...
Cisco Switching/Routing :: 6513 Switch Boot To ROMmon
May 9, 2012i have a Cisco 6513 it is used one, i have tryed to boot it but it did not work, it alwayes go to rommon mode and i am not able to know what is the issue,
when it boot i get the below outpot from the switch.
System Bootstrap, Version 8.1(3)
Copyright (c) 1994-2004 by cisco Systems, Inc.
Testing lower main memory - data equals address
[Code].....
Cisco Switching/Routing :: 2960 / 6513 - Multicast Between VRF On Same Switch
Sep 3, 2012I am working on Multicast scenario, There is one 6513E switch one 2960 switch. Two VRF's are configured in core switch (6513) IPTV-SRV and Villa-VRF IPTV-SRV vrf has IPTV server and Villa-VRF has IPTV i.e. client.
V LAN 30 is mapped to IPTV-SRV vrf with subnet address 192.168.30.0/24
V LAN 12 is mapped to Villa-VRF with sub net address 192.168.12.0/24
I did the following configuration for VRF but its not working . i am not an expert in multicast design but seems i did most of the configs.
ip vrf IPTV-SRV
rd 30:1
mdt default 232.1.1.1
route-target export 30:1
route-target import 10:1
[code]...
Cisco Switching/Routing :: Lost Port Channel Between 6513
Feb 24, 2012We have 2 6513's that are linked via 2 10 gig interfaces, using an LACP channel.I received an alert this aft stating that the far 6513 was unreachable and the port channel int PO3 had gone down, the 2 10 gig interfaces had also gone down on either side. 5 mins later PO3 had resestablished itself and has been fine since. [code]
View 4 Replies View Related