Cisco Switching/Routing :: 2960 / 6513 - Multicast Between VRF On Same Switch
Sep 3, 2012
I am working on Multicast scenario, There is one 6513E switch one 2960 switch. Two VRF's are configured in core switch (6513) IPTV-SRV and Villa-VRF IPTV-SRV vrf has IPTV server and Villa-VRF has IPTV i.e. client.
V LAN 30 is mapped to IPTV-SRV vrf with subnet address 192.168.30.0/24
V LAN 12 is mapped to Villa-VRF with sub net address 192.168.12.0/24
I did the following configuration for VRF but its not working . i am not an expert in multicast design but seems i did most of the configs.
ip vrf IPTV-SRV
rd 30:1
mdt default 232.1.1.1
route-target export 30:1
route-target import 10:1
[code]...
View 3 Replies
ADVERTISEMENT
Aug 1, 2007
I am running a network comprising of Catalyst 6513's with SUP7203B's. at present we have 800 VLAN's as we make use of a VLAN per access layer switch model.
I know have a problem that as soon as I enable multicast routing my SUP720's CPU runs at 100% and the system goes into a slowdown.where I can find information on the scalability of Multicast?
View 15 Replies
View Related
Dec 6, 2009
I am trying to make the multicast working between few hosts inside a single vlan. Host are running mysql cluster and Multicast is used to send master/slave status information to the IP 228.10.10.10 on port 45566.The vlan is defined in FWSM and the host are connected via the core-switch(6513). (hosts-->core-sws--->fwsm)I have tried searching the documentation, but couldn't find specific info to enable multicast between hosts residing in same vlan. FWSM is running code 3.1(4). since the hosts are residing in the same vlan, I am thinking of applying the <multicast-routing> just for that SVI in FWSM.
View 6 Replies
View Related
Jun 17, 2012
A 2960G switch is doing IGMP snooping and is configured as the querier. There is no multicast routing.
Port 1 - Video Set Top Box A
Port 2 - Video Set Top Box B
Port 3 - Multicast Source
Both Set Top Boxes A & B are set to receive the video delivered in the same multicast group.Every 60 seconds the switch generates an IGMP General Query message which is sent out all the ports in the VLAN.There is a 10 second timeout in the Query message. Devices that wish to join (or remain joined) to the multicast group have this amount of time to respond with a Join Message directed at the multicast group. Devices deliberately wait a random duration within the timeout time before replying.
For some reason (which I don't understand), if the switch receives a Join request message from a Set Top Box, it forwards that messages out of the port to the other Set Top Box. So, let's say Box A responded with the Join Message first. Box B now sees the Join message and now thinks there is another multicast receiver on its branch of the network, so it suppresses its Join Message to avoid sending an unnecessary message.If by chance Box A responds first 2 or 3 times in a row, the switch will not have seen a response from port 2 for awhile, so it prunes that port from the multicast. Eventually, Box B responds first and gets re-joined onto the multicast. It is now Box A that may get pruned if it is consecutively slower.
How do I prevent the switch from replicating the Join message out to the other Set Top Box? I have verified this behavior with Wireshark. But, I believe the Join message is only supposed to be forwarded to a multicast router (if there is one - and there isn't), not to other ports.The 2960 is running 12.2(58) SE2.
View 3 Replies
View Related
Dec 6, 2012
Attached setup i am planning for testing multicast output from different vendors using VLC and STB. This Setup made to test the picture quality between the vendors at the same time on the multi viewer screen.
1) Only a 2960 Gig port switch with only one L2 v lan with IGMP snooping enabled.
In this scenario where Source and receivers are in the same L2 v lan ( no L3 interface is involved) hope i would able to test all the multicast sources with out any additional configuration on the Cisco switch.
View 6 Replies
View Related
Jan 29, 2012
[URL]
We found out that only local multicast ip address range is not passing between the sites, any other range is passing, local range is 239.0.0.0 and above.
We have two different datacenters, the internal switch is 2960S (Stacked) with 1-10 vlans and the external switch is 3560E, the external switch is adding another tag (qinq, dot1q), vlan 611, and send the packets to metro line to the other site.
on the other site we have the same configuration.
internal switch from site A is configured with igmp querier and the internal switch port on site B connected to the external switch is configured as mrotuer port.
multicast and igmp is passig between the sites, but the local multicast range is not passing, igmp filterring is configured on all port but no profile is defined and no ports are filterred, on the external switch igmp snooping is disabled.
View 4 Replies
View Related
Dec 8, 2011
How do you enable multicast traffic on 2900 series switches?
View 7 Replies
View Related
Apr 28, 2012
We have Communication Media Module (WS-SVC-CMM) mounted on 6513 switch. It went down twice and we brought it up by applying "power enable module".
View 4 Replies
View Related
Mar 20, 2013
Need your expert input in sorting out the below problem.I have a cisco 6513 switch which is going into SP mode after a reboot whci i have done during BCP activity in my organization.Below are the log for your reference.
Code...
View 1 Replies
View Related
May 9, 2012
i have a Cisco 6513 it is used one, i have tryed to boot it but it did not work, it alwayes go to rommon mode and i am not able to know what is the issue,
when it boot i get the below outpot from the switch.
System Bootstrap, Version 8.1(3)
Copyright (c) 1994-2004 by cisco Systems, Inc.
Testing lower main memory - data equals address
[Code].....
View 3 Replies
View Related
Jul 15, 2012
I have been getting the logs in my cisco 6513 switch [code] On further investigating in the module 9 which has a DFC card also , we found the source of this error whether it is a source of any upcoming potential impact or can be simply ignored
View 3 Replies
View Related
Mar 2, 2012
I have two servers, connected on two(Different) 6513 directly connected switches. Both these servers are in the same Vlan.
I have to monitor communication these two servers. I have a system connected on one of the 6513 switch, where network tool wireshark is installed.
How to configure span port.
switch 6513-1# show run int Gi10/43 --------------------Server 1 is connected
switch 6513-2# show run int Gi9/45 ------------------------Server 2 is connected
switch 6513-2# show run int Gi9/46 ------------------------System on which network tool wireshark is installed.
View 9 Replies
View Related
Apr 7, 2012
After a power problem at our data centre we find Module 11 of our Cisco 6513 Core Switch in PWR Down state.Show Module 11 returns: Status: PWRDownShow Power Status Module 11 returns: OperStatus Off (Module Reset due to an exception or user request).The command:
Power enable Module 11 was issued and returned the following: %PM_SCP-SP-1-LCP_FW_ERR: System resetting module 11 to recover from error: Linecard received system exception. Errcode = 2509000001.%OIR-SP-3-PWRCYCLE: Card in module 11 is being powercycled Öff (Module reset due to exception or user request%C6KPWR-SP-4-DISABLED: Power to module in slot 11 set off (Module Reset due to exception or user request),We have restarted the switch twice. The module is currently not passing traffic causing downtime to services.
View 6 Replies
View Related
Jun 18, 2012
I have a supervisor blade, (VS-S720-10G-3C), in a 6513 that is faulty and needs replaced. Do I need to replace the IOS on the new supervisor blade to make sure it is the same as the IOS image that is on the Active supervisor module, or will it synchronize automatically?
In the synchronization process, the active supervisor engine checks the standby supervisor engine run-time image to make sure that it matches its own run-time image. The active supervisor engine checks three conditions:
#
•If it needs to copy its boot image to the standby supervisor engine
#
•If the standby supervisor engine bootstring needs to be changed
#
•If the standby supervisor engine needs to be reset
I was reading the above documentation that mentioned the active supervisor should copy the image if it detects a newly installed standby supervisor blade with a different image, is this correct or was it referring to synchronizing the configuration file?
View 3 Replies
View Related
Oct 29, 2012
we have a chassis 6513-E and a module WS-X6748-GE-TX, I'd like to know if could I put this module in any slot, since the documentation from Cisco says that any slot from a chassis 6500-E Series can support this module. And then in the documentation of WS-X6748-GE-TX says that this module is not compatible in the slots 1-8 of the 6513 chassis, only from 9th to 13th slots, in those slots from the 6513-E we already have 4x WS-X6748-GE-TX, and we'd like to know if could we put the module in the rest of the slots. The 6513, and 6513-E is kind of confusing.
View 4 Replies
View Related
Mar 7, 2012
I just added a X6704 card to our 6513 switch, and it is not working correctly. We are running 12.2(33)SXI5. [code]
View 5 Replies
View Related
Feb 20, 2012
How much is the limit for the creation of PortChanel in a Core Switch 6509 and 6513?Is there a limitation byu hardware?
View 7 Replies
View Related
Mar 14, 2013
I need a switch to configure a static ARP entry for a MS NLB multicast.
Could answer me if I can do with the SRW2024-K9-BR?
View 4 Replies
View Related
Jul 10, 2012
Any switch that supports 4096 multicast groups?I am working on a system that includes over a dozen catalyst 2960 switches. The customer has pointed out the 2960 switch does not satisfy the requirement to support 4096 multicast groups (even though it is more than adequate for the number of active multicast groups). It looks like the 3560 supports more multicast groups than the 2960, but is still far less than the requirement.
View 1 Replies
View Related
May 21, 2013
I have a Cisco SG 300-20 as the core switch, layer 3. It is 192.168.4.6 on VLAN1 and 192.168.5.1 for VLAN2 (VOIP). All the ports are set in trunk mode. DHCP relay is setup on this switch.
The phones connected into a layer 2, Catalyst 2960-S switch. All ports are set in trunk mode. Default gateway on it is set to 192.168.5.1.
DHCP for both VLANs is provided by a Windows Server 2008 R2 server (the relay IP 192.168.4.15).
There is also an ASA 5510 in the mix which is 192.168.4.1. It has a route added to it for the 192.168.5.0 network to go to the SG 300 (192.168.5.1).
Just the two switches can ping each other on the 192.168.5.x network when I "add vlan 2" to the trunk port that is connected between the SG 300 and the 2960. The phones don't get DHCP on the 2960 switch. And I cannot ping 192.168.5.x from the ASA or anything else on the 192.168.4.x network.
After a bit of reading on intra-vlan routing for the SG 300 switch, I am thinking the SG 300 has to be the "center" of things so I need to make it 192.168.4.1 to be the gateway for both VLANs and change the ASA to 192.168.4.2 for VLAN1, etc. And I really can't do asymmetric routing with this switch.
View 1 Replies
View Related
Nov 16, 2011
Does the Model "WS-C2960-24PC-L" Supports IP Routing or not?
View 9 Replies
View Related
Jun 13, 2012
I'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
View 11 Replies
View Related
Feb 5, 2013
I have a statck of 4 2960s switches, with POE powered access points on 2 of them. All of the access points appear to be functioning normally. For some reason, on 3 interfaces connected to access points, I get the following when issuing show interfaces status:
Gi3/0/9 connected: T 7 a-full a-1000 10/100/1000BaseTX
^
My question is regarding the "T" in the status field. I can't find any documentation on this.
View 5 Replies
View Related
Dec 12, 2006
I have CISCO 2960 switch at my LAN. How to configure its IP address from console or hyper terminal ?
View 11 Replies
View Related
Jan 14, 2013
I am trying to configure a new 2960 POE switch, but seem to me the int fa0 is layer 3 interface. Is any way we can convert it to a switchport, so we can connect it to other switch in trunk mode?
View 1 Replies
View Related
Aug 20, 2012
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
View 3 Replies
View Related
Apr 29, 2012
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
View 5 Replies
View Related
Jan 24, 2012
I am setting up a new 2960-S switch and none of the recommended username and passwords combinations work. I have tried CIsco Cisco, <blank> cisco and various other permutations.
I have tried to reset the switch to factory defaults and it still doesn't work. The switch is currently connected to a 3560G and has been assigned an IP. If I try to access it from Network assistant it shows as unmanaged and I get prompted for a username and password.The switch is connected to another new 2960-S via a FlowStack module.
View 4 Replies
View Related
Nov 28, 2012
I need to know the 172cisco 1 router support to IPv6 & it support to IPv6 then which IOS is required for it.Also I need to know the cisco 2960 switch is support to IPv6?
View 3 Replies
View Related
Feb 19, 2013
Currently Being Moderated password recovery
View 3 Replies
View Related
Feb 16, 2012
I am a new network engineer on a retail company and I am having a problem on the High utilization of my 3-stack switch 2960 only during Peak Hours of the Store Sales.
Note: on Peak hours, it is peaking at 90-95 %
here is the utilization after Peak hours:
4444333334444433333333333333333333333333333333333333333333
[Code]......
View 4 Replies
View Related
Feb 9, 2012
I can understand it 's one of those very basic questions , but how do I identify a Switch is Layer 2 or Layer 3 ?Looking through # show version command and checking the IOS version to be IP BASE or LAN BASE . Is it the right way ?Cisco 2960 is a Layer 2 or a Layer 3 Switch ? I noticed that access-lists could be configured which means that it 's a Layer 3 Switch , right?
[code]....
View 5 Replies
View Related
Oct 22, 2012
I have a Cisco 1841 router connected to a Cisco 2960 switch.Users behind the router can't access the internet but when someone is directly connected to the switch with his PC and uses the IP Address found on the WAN port of the router, he's able to go on to the internet. [code]
View 4 Replies
View Related
