Cisco Switching/Routing :: Not Logging All Levels Of Sylog Messages From Core Switch 4503
Apr 23, 2012
We had a core switch(4503) in our environment and recently we tried to enable syslog in the switch. But the syslog server doesnt receives all the configured level messages from the switch. Following is the only message getting in syslog server after the configuration change in switch.
%SYS-5-CONFIG_I: Configured from console by CWLMS onvty1
(No Traffic related messages like acl deny traffic, spanning tree events etc are getting to syslog server as well as log buffer of the switch)
Following are the logging configuration for the core switch
logging monitor informational
logging facility syslog
logging source-interface Vlan44
[Code]....
1) Is there any more configurations required for getting all traffic related messages, (i mean all possible messages - upto level 7 - debugging)?
View 3 Replies
ADVERTISEMENT
Feb 14, 2012
We had a core switch(30 vlans) in our environment and it's noticed that CPU utilization of the core switch is showing high during recent days. I have checked logs and processes, but couldn't find the root cause. The issue found only in the office hourly only(after that the cpu utilization is idle and normal). I have already referred the following link to troubleshoot the issue " [URL]
see the following outputs from the core switch
CPU utilization for five seconds: 99%/0%; one minute: 99%; five minutes: 99%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
30 6687557041432420936 466 47.52% 47.10% 45.98% 0 Cat4k Mgmt LoPri
55 30667074884269560256 0 45.36% 45.50% 45.85% 0 IP Input
29 28552856922870089254 0 3.59% 3.50% 3.57% 0 Cat4k Mgmt HiPri
[code]....
Note: Each Invalid source mac entry in each day from same port (above is the output after clearing logs before 3 days)
My queries regarding the issues are following
1) How can we find root cause regarding the high cpu utilization?
2) Is a single invalid mac address makes the cpu highly utilized for suppressing it?
View 10 Replies
View Related
Jan 13, 2012
We have two core switches in our network (Cisco WS-4503). HSRP is working as Active-Standby mode. Recently it has been found that core 1 (which is in active mode) shown high CPU load (60% - 100%). Also found that the below mentioned process takes more CPU. Our network consist of around 30 Vlans. We have already checked for the solution in Cisco website [URL] but couldn't find exact reason. see the below outputs for core 1 switch.
Core1# sh processes cpu sorted
CPU utilization for five seconds: 55%/3%; one minute: 65%; five minutes: 71%PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 30 1606933521086983644 147 24.79% 29.93% 35.85% 0 Cat4k Mgmt LoPri 29
[Code]....
View 3 Replies
View Related
Jul 8, 2012
recommend a cisco core switch and access switches in IPTV network infrastructure?I was ask to implement a network for IPTV system but i don't have idea what will be the model i will use.
Core Switch = Cisco 4503
Access Switches = Cisco 3560X
View 3 Replies
View Related
Dec 14, 2011
we have Core-Siwtch 4503 in the main building which is connected to another Core 4503-E in another building ,, now our PCs connected to the 4503-E ,,, any XP M/C can pick an Dhcp-ip but and M/C run Win.7 Cannot !!
action taken :
1st we try to connect our win 7 pc in the node which was connected to xp M/C ,, and it didnot take ip from the DHCP . ,, 2
2nd we ensure from the core-switch configuration and its normal with no mistake
3rd trying to use tool from Microsoft Fix-it Center whih name is ( Microsoftfixit 50475 ) which is just .msi file but the problem face us is that this tool donnot accept to run on win 7 cause its made for vista .
4th after some researchs we notic that there is some modifications have to be performed on registery by disabling the dhcp broadcast flag we did it but nothing change yet
5th now we are waiting to perform another action which is Disable the IP Helper service in win 7
View 6 Replies
View Related
May 9, 2012
I have a situation in which I want to log a specific message (informational - 6 level), but don't want to enable informational logging and get all the messages that come with it. Is there a feature in IOS, 3560 12.2(25r)SEE4, similar to the 'logging lists' feature on the ASA that allows you to specify logs that you want to capture without having to change your logging level? I didn't want to have to write an EEM applet for this, but if that's the only way, I'd consider it.
View 3 Replies
View Related
Feb 9, 2013
We have microsoft servers and other application servers (around 12 in nos) which should have gig connections to the access switch. In turn this access switch will be connected to our distribution switch 4503. Which model of access switch best fits from the below 3 models. It should be cost effective as well.
WS-C2960 S-24PS-L
WS-C2960-24TS-L
WS-C3560G-24TS-S
View 8 Replies
View Related
Jan 9, 2012
Currently we have cisco 4503 switch in one of our location without redundancy which servers below,
300 user (desktop & ip phones)
5 vlans
15 access switches are connected
one L3 connectivity.
Actually i want to understand is it really necessary to have 4503 or we can go for 4900 series as we are planning to have redundancy in distribution segment.
Which is the best L3 switch in the above scenario and how to measure the overall performance of the current 4503 switch...
View 4 Replies
View Related
Sep 13, 2011
We have Cisco 4503-E switch and software version is cat4500e-universal.SPA.03.01.01.SG.150-1.xo1.bin. Now i have uploaded cat4500e-universal.SPA.03.02.01.SG.150-2.SG1.bin IOS-XE software in the switch and want to boot the switch from this image.
View 17 Replies
View Related
Jun 19, 2011
Is it possible to configure the ASA to:
log syslog informational to one host
and
log syslog critical to a different host
It seems that the ASA allows you to only specify 1 logging severity level for all syslog hosts..
View 1 Replies
View Related
Jan 24, 2012
While working at a client site today, I was troubleshooting some ICMP connectivity for a network we have created.I turned on 'debug ip icmp" on the 3550 switch int he middle, and was inundated with the following debug output:
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
Jan 25 11:01:14.641: ICMP: dst (172.16.1.7) port unreachable rcv from 172.16.1.5
[code]....
This output fires several times a second, and based on how often it is firing, I am curious if it may be a culprit with respect to the fact that the client has indicated that they have some slow internet.Should the next step be to look at the workstation at 172.16.1.5?
View 10 Replies
View Related
May 31, 2012
we need to relocate our core switch 6500 with sup 720 to another bldg
what is the command to gracefully shut it down I mean power off
I was told one can just switch off the power
View 4 Replies
View Related
Jun 2, 2013
i configure the uplinks as etherchannel, i configure two svi interface on core switch int vlan 51(192.168.51.1) and int vlan 50(192.168.50.0) for this two svi int i configured two dhcp pool , when any of the pc is requesting for dhcp add i am getting dhcp request failed/
View 7 Replies
View Related
Jun 7, 2012
I'm trying to decide what switch to use as a core for 500 users. I'm currently looking at either 2 x 3750X stacks or 2 x 4500s with dual SUPs and PSUs, both options will provide the number of switchports required without the need for additonal access layer swiches. Which switch option is best to go for here? All of our services will be located in our data centre which will be connected using 2 1000Mbps MPLS circuits. I wont need any advanced L3 features and we are not likley to scale over 450 users. Also is it ok to use the dual switch stacks or chassis to provide the collapsed core/access layer or is it best to have a dedicated core (using one of the above options with less switchports) and having a dedicated accesss layer using 2960Gs for example. Our structured cabling terminates in a single comms room so we wont need to distribute switches throughout the office.
View 3 Replies
View Related
Nov 4, 2012
I have 2 units core swicth C4510R+E SUP7-E need to connect together for redundant purpose , i bought also 4X 10GE uplinks for each core switches .May i know how i shall connect both core switches together using my spec Catalyst 4500 E-Series 12-Port 10GbE (SFP+) ?
View 6 Replies
View Related
Jul 15, 2012
I have been getting the logs in my cisco 6513 switch [code] On further investigating in the module 9 which has a DFC card also , we found the source of this error whether it is a source of any upcoming potential impact or can be simply ignored
View 3 Replies
View Related
Dec 20, 2011
I am experiencing high cpu utilization in my 4000 series core switch.
I checked the loggs. i saw some strange loggs.
Please see the below logs:
Code...
What is the "invalidsourceaddresspacket" ?
Is this is due to some virus attack or something?? Also one more thing this switch is the Active router in HSRP.
View 12 Replies
View Related
Sep 21, 2012
I have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.
View 40 Replies
View Related
Oct 14, 2012
We have two 6500 core switches and one(primary) of them is running in VTP transparesnt mode and the other (secondary) one is running in VTP client mode. I would like to change the VTP mode of the second switch to transparent mode. Would it cause any issue. I guess i have to create VLANs onto the switch.
View 7 Replies
View Related
Apr 13, 2013
I have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.
View 22 Replies
View Related
Jun 5, 2013
I am planning to migrate the core switch from cisco 3750 to Cisco catalysts 6513 switch. What could be the best approach to minimize the downtime or avoid disrupting the production. I have couple of thoughts, one method is to build the core and then replace the existing core, another option is to build the new switch as the second VTP server and once it recieves all the VTP information then disconnect the old server.
View 6 Replies
View Related
Aug 30, 2012
choosing a core switch, to replace a swich 3com model 4924, its main function is to support a 4-LAN switch cisco 2960 (100 users) and a ring cluster of 12 servers.obs. Current 3com core switch has 56 Gbps performance and 41.6 million packets per second.
View 3 Replies
View Related
Nov 2, 2011
i am trying to upgrade the software of the core switch 4503e, i could not get the managemenet ip address up and running. what i did is the following :
interfave vlan 1
ip address 192.168.1.1 255.255.255.0
no shu
then my laptop ip address is 192.168.1.100 255.255.255.0?result pinging from CLI is request time out.is there any els command where i need to input ?
View 13 Replies
View Related
May 7, 2013
I want to upgrade IOS for my production core 3750 switch. Below is Show version/fash output. I have IOS image "c3750-ipservicesk9-mz.122-55.SE7", need to confirm below concerns:-
1-As this is stackable switch do i need to upgrade on all Switch..i can see there are 3 flash while doing show flash?
2-Is above IOS image support with my switch? do i able to enable ssh?
3-is flash memory is enough to succefully upgrade IOS?
4-Any other point which i should keep in mind before upgrading..any special feature which this IOS wont support.
View 11 Replies
View Related
Nov 18, 2012
Two Cisco 3750X can be stacked together to ensure redundancy.Is the attached topology feasible for access layer redundancy?
View 5 Replies
View Related
Sep 16, 2012
I have the following: 1 5520 ASA connected to the internet, 2 core switches, and several access switches.Aside from implementing RSTP, VRRP, hard code access and trunk ports, is there any other recommendation you would like to add.
View 7 Replies
View Related
Jan 25, 2012
i'm already has one internet connection is conecting directily to the Core Switch 6509, and the Switch is route any internet request with default route:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.170.10.10
10.170.10.10 is --> Next hop for the DSL router internal IP, and it's working fine.
We have a new internet connection with another ISP/ with another DSL router, how to connect both of them to exit from the Core Switch 6509.
is it ok if i make another default route to the Next hop to the new DSL router as:
SW6509-conf)# ip route 0.0.0.0 0.0.0.0 10.80.10.10
10.80.10.10 is --> Next hop for the new DSL router internal IP.
View 6 Replies
View Related
Oct 6, 2012
To setup SG300-20 as CORE switch and SF100-48 as Distribution switch.SG300-20 will have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 DATA
-172.168.0.1/24 VOICE
SF100-48 will also have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 Desktop/Laptops
-172.168.0.1/24 IP phones
Problem is when I tried to assign IP to any VLAN's the switch will just hang and loose my connection the light will stop blinking it will steady and i unable to access the switch until i turn off again?
View 1 Replies
View Related
Feb 2, 2013
I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies
View Related
Oct 23, 2011
What is PIM? give me an example when I will use and not use the PIM command.
View 4 Replies
View Related
Feb 20, 2012
How much is the limit for the creation of PortChanel in a Core Switch 6509 and 6513?Is there a limitation byu hardware?
View 7 Replies
View Related
Oct 24, 2011
I have an Cisco 6500 CS and there is a Cisco Unified Communication Manger Server connected directly to the Core Switch.I tried to change duplex and speed ( fix and auto ) for both sides, but the same problem.
View 9 Replies
View Related
Jan 28, 2013
Is there any challenge to upgrade core switch 6500 series from Nexus 7009 which runs NxOS, because i have 3750X series switches connected at distribution and access layer in my network topology??
Is there any challenge if we place NxOS in core and IOS in distribution and Access layer??? how we are able to match sh run config in existing 6500 switch to Nexus 7009 NXOS?
View 9 Replies
View Related
