Cisco Switching/Routing :: 3750G / Switch Loses Connecting To Distribution SW
Feb 21, 2013
The two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies
ADVERTISEMENT
Jan 30, 2013
We have 4507 distribution switch in our network.I am trying to enable ssh in those switches but seems that ssh command is not supporting. IOS version - cat4500e-universal.SPA.03.03.00.SG.151-1.SG.bin
View 1 Replies
View Related
Oct 6, 2012
To setup SG300-20 as CORE switch and SF100-48 as Distribution switch.SG300-20 will have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 DATA
-172.168.0.1/24 VOICE
SF100-48 will also have 2 VLAN(DATA and VOICE)
-192.168.14.1/24 Desktop/Laptops
-172.168.0.1/24 IP phones
Problem is when I tried to assign IP to any VLAN's the switch will just hang and loose my connection the light will stop blinking it will steady and i unable to access the switch until i turn off again?
View 1 Replies
View Related
Jul 18, 2011
I have issue with connectivity 3750G with Dlink Switch, it cannot connect to non-cisco switch with fiber , But CISCO to CISCO switch it shows connectivity. My question is that is there any configuration on Cisco 3750G switch to connect with non-cisco switch through fiber (SFP) ?
View 2 Replies
View Related
Oct 8, 2012
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
View 2 Replies
View Related
Jan 2, 2013
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies
View Related
Jun 17, 2012
have one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
View 2 Replies
View Related
Feb 7, 2011
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
View 9 Replies
View Related
Apr 8, 2013
I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs. These 2 current switches are the VTP server for a small domain. I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?
View 7 Replies
View Related
Mar 7, 2013
I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies
View Related
Apr 14, 2012
if we can stack the 3750G switch with a 3750X switch ?
View 7 Replies
View Related
Apr 23, 2013
I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
View 2 Replies
View Related
Mar 30, 2013
i am not able to add new 3750G switch into existing domain even after the domain name is correct and unable to authenticate with tacacs.
View 5 Replies
View Related
Nov 3, 2011
I am about rip and replace my current 3750G stack with a 3750X stack. I have trunked over vlan and vtp info and implemented a config so it should be ready to go other then moving cables onto it. However one thing I want to correct with our current setup is that the root bridge on our vlans including vlan 1 is on a separate set of switches that we control, however I would like this new stack to be the root bridge for all of our vlans. It will be the central set of switches that all other switches trunk into. I have pre-set higher spanning-tree priorities for each vlan on the new stack so I expect as I move lines into it that the tree will be re-calculated with it as the root bridge. I've ensured that there are no root guards on any of the other switches trunks and priorities are all at default levels for each vlan. Should I enforce root guard on the trunk interfaces of the new master stack? Most of the trunks are port-channels to the other switches - do I need to set root guard on the Port channel interface or on the individual ports that make up the Port channel? On both? Any other recommendations in regards to implementing spanning-tree with the new stack? I know using port channels eliminates a lot of potential for loops but not every trunk is and I'd still like to have spanning-tree on.
View 1 Replies
View Related
Feb 19, 2013
I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
View 15 Replies
View Related
Apr 22, 2012
Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies
View Related
Nov 24, 2011
I try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 Replies
View Related
Mar 30, 2013
I am cascading one new switch 3750G (int Gi1/0/1) with an existing 3750G (int fa1/0/26) switch.. But the interface fa1/0/26 goes in err-disable state even after NO SH.. also i have diable Spanning treebpdu guard and disable spanning tree portfast. But still the issue is not resolved.
View 6 Replies
View Related
Dec 7, 2011
I am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies
View Related
Feb 29, 2012
I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
View 19 Replies
View Related
Jan 15, 2012
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
View 1 Replies
View Related
Feb 12, 2012
using the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies
View Related
Oct 20, 2012
Imagine I am designing a small network with a C2900 router running OSPF and in the future BGP with service provider. Please see attached diagram.The router is connected to (2) C3750 Layer 3 distribution switches. Then one C3560 layer 2 switch to serve future IP phone users and desktops.
Question:
a)If I connect the router interface to the (2) 3750 switches, if I make the router interface fa0/0 and fa0/1 as a trunk to accomodate VLAN 200 and other future VLANs, don't I have a problem with overlapping networks between router interface fa0/0 and fa0/1?
b)Alternatively, I could make the Router1 fa0/0 and fa0/1 configured with IP addresses and advertised in OSPF. Then the SW1 fa0/24 and and SW2 fa0/24 I could make as 'no switchport and create a routed interface port' with IP addresses, also running OSPF. Question is, from a scalable design perspectie, would you create 2 management networks and use those when assigning the IP addresses for Router1 fa0/1 and fa0/2? Because again Router1 fa0/1 and fa0/2 obviously need to be placed on different networks to avoid overlapping. So my question is more about proper network planning design to make this scalable to accomodate future VLANs in the future.Using trunks between the Router1 and SW1 option:
Router1
int fa0/0
description connection to SW1
no ip add
int fa0/0.200
[code]....
View 3 Replies
View Related
Oct 9, 2012
This is existing network diagram and find attached file for configuration of Router and L3 Switch:ISP provided 6 Mbps internet access link with ethernet Handoff which is terminated over Cisco 1841.ISP also provided pool of 30 Public ip's 125.63.74.33 /27 , range from 125.63.74.34 to 125.63.74.62.In my current setup, all Inside to ouside traffic going out through 125.63.74.34 public ip because this public-ip NAT overload with Router F0/1 interface.
1) I want to divide 6 Mbps link physically into three parts 2Mbps, 2Mbps, 2Mbps for three VLANs.
2) I want to also configure each vlan IN/OUT traffic with different Public ip. is it possible or not ?
Vlan2 = 172.25.162.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.40
Vlan3 = 172.25.163.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.41
Vlan4 = 172.25 164.0 /24 => Inside to outside / Outside to inside traffic through 125.63.74.42
How can i configure above desired setup with CBWFQ
View 23 Replies
View Related
Apr 9, 2013
I had a lot of questions when I began planning a pair of Nexus 7000 switches as a replacement for our 6500. How to publish my design and config. This is a medium sized network. I would have loved to see somone's configs for a similar implementation.
[URL]...
View 5 Replies
View Related
Aug 29, 2012
I have some questions in regards to network equipment I want re-utilize for my distribution layer in one of my buildings.The choices at the moment are:
OPTION 1.) 2x WS-3550-12G's (HSRP)
OPTION 2.) 1x WS-6509 with cards:
What option would be better from a performance aspect? We want to have network, voice, and wireless data go through this distribution layer switch(es).This is exisiting equipment I already have and can not buy anything else at the moment.
View 2 Replies
View Related
Mar 21, 2012
This is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
View 5 Replies
View Related
Feb 10, 2013
We are using CISCO Catalyst 6500 switches as collapsed core/distribution switches (2 layer architecture). I want to connect approximatly 10 application servers to the network. Can I connect the servers directly to the catalyst 6500 switches using WS-X6148E-GE-TX line cards? The other option is to use access switchs and then connect the servers to the catalyst 6500 through access switch(Catalyst 3750).
View 6 Replies
View Related
Sep 17, 2012
When i connect two cisco 2960 series switchs via stright trough cable causes delay in transmission sw1 has vlans and having trunk port connected to router all vlans are able to access internet sw2 is connected to vlan5 on switch1 sw2 has factory default configuration computers on sw2 can access internet but I have low bandwith problem on sw2 there is transmission delay problem?
View 1 Replies
View Related
Apr 13, 2013
I have a 3750X four-switch stack acting as the core of a fairly simple LAN. All I need to achieve (and this seems inordinately hard, but it is entirely likely that I'm just being dense) is to get access to the internet through my core switch, through the firewall and out through my VSAT. I've spoken at some length with the firewall providers (Cyberoam) and they tell me all I need to do when I migrate onto my new system (Cyberoam is currently in place at the entrance to our existing LAN) is change the local IP address of the Firewall, plug in the new switch to the LAN port, and away I go. Tried that, didn't work, so obviously I'm missing something.
View 22 Replies
View Related
Jan 5, 2011
I have got a new 48port Cisco catalyst 4948 switch, which I configured as a VTP client and connected to Cisco 3750 which is a VTP Server (this switch is on production network). I connected port g1/0/48 from 3750 to port g1/48 on 4948 through a straight cable and made both ports as trunk port (I also tried through cross cable). The problem is these two switches are not detecting. For testing I connected a PC directly to one of the port on 4948 (making that a switch port) still the LED on switch didn’t glow up. Is there any special command needs to be run on 4948 switches to activate its physical ports?
View 7 Replies
View Related
May 3, 2012
I'm introducing a Cisco 3750 switch into a Avaya environment for testing/lab. I'm concerned about any STP, VTP problems I might create as I'm going to give a address on the Management VLAN and connect it to a trunk port on a ERS5520 Avaya. I've set the switch to transparent mode and the VTP revision is set to 0. I've checked the STP priority but it doesn't give any - there is no output because it is not connected. I wouldn't be so concerned but, I'm not sure if any config has been on it before.Also, is there any way for me to see the STP prioroity without having it connected?
View 10 Replies
View Related
Feb 19, 2012
In one location we have a HP 2510-48 port switch which we need to connect to a Cisco 3560 switch. The problem I have is that we have issues connecting fibre to the HP switch, so I have decided to attached a CAT 5 to Fibre convertor at this end and another to the cisco switch.
My question you can not connect a HP switch to a Cisco switch, is this true or do I just need to confirgure something on the ports.
View 2 Replies
View Related
