I try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 RepliesHas any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
I have a WCCP Configuration on a Catalyst 3750G and a IronPort Webappliance. I have configured this situation many times before with cisco asa and ironport wsa, but with a switch, this is my first time.
VLAN 147 is a transportation vlan between the cisco switch and a hp coreswitch with the clients and servers behind the hp coreswitch.
VLAN 147 IP Address of the Catalyst is 172.30.47.1
IP of the IronPort Appliance is 172.30.47.10
IP of the HP Coreswitch is 172.30.47.2
Plan is to redirect the webtraffic coming from clients and servers from the 10.0.0.0/8 net behind the hp switch to the ironport wsa. In have configured these settings.
ip wccp web-cache group-list 15 password 7 091D1C5Aip wccp 80 redirect-list 16 group-list 15 password 7 14464058
interface GigabitEthernet1/0/22 description IRONPORT P1 BUWOG switchport access vlan 147 switchport mode access
interface Vlan115 ip address 172.30.15.2 255.255.255.0 standby 10 ip 172.30.15.1 standby 10 priority 90 standby 10 preempt standby 10 track Vlan115!interface Vlan147 ip address 172.30.47.1 255.255.255.0 ip wccp web-cache redirect in ip wccp 80 redirect in
[code]....
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies View Relatedhave one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs. These 2 current switches are the VTP server for a small domain. I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?
View 7 Replies View RelatedI am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies View Relatedif we can stack the 3750G switch with a 3750X switch ?
View 7 Replies View RelatedI am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
The two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies View Relatedi am not able to add new 3750G switch into existing domain even after the domain name is correct and unable to authenticate with tacacs.
View 5 Replies View RelatedI am about rip and replace my current 3750G stack with a 3750X stack. I have trunked over vlan and vtp info and implemented a config so it should be ready to go other then moving cables onto it. However one thing I want to correct with our current setup is that the root bridge on our vlans including vlan 1 is on a separate set of switches that we control, however I would like this new stack to be the root bridge for all of our vlans. It will be the central set of switches that all other switches trunk into. I have pre-set higher spanning-tree priorities for each vlan on the new stack so I expect as I move lines into it that the tree will be re-calculated with it as the root bridge. I've ensured that there are no root guards on any of the other switches trunks and priorities are all at default levels for each vlan. Should I enforce root guard on the trunk interfaces of the new master stack? Most of the trunks are port-channels to the other switches - do I need to set root guard on the Port channel interface or on the individual ports that make up the Port channel? On both? Any other recommendations in regards to implementing spanning-tree with the new stack? I know using port channels eliminates a lot of potential for loops but not every trunk is and I'd still like to have spanning-tree on.
View 1 Replies View RelatedI wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies View RelatedI am cascading one new switch 3750G (int Gi1/0/1) with an existing 3750G (int fa1/0/26) switch.. But the interface fa1/0/26 goes in err-disable state even after NO SH.. also i have diable Spanning treebpdu guard and disable spanning tree portfast. But still the issue is not resolved.
View 6 Replies View RelatedI am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies View RelatedI currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
I have a Catalyst 4006 switch in production and a spare switch of same model. I have to quickly copy the configuration from production switch to spare switch (both L2 and L3 configurations) How do I do that?
View 6 Replies View RelatedWe have to connect two 3750G switches to some HP machines. Those machines have several network interfaces, which are going to be configured in several bondings. The load balancing mode they want to configure is mode 6, alb. We have investigated and it is: [code] Receive load balancing is achieved through ARP negotiation.We would like to know if it is supported to be connected to a 3750G an if an special configuration is needed.
View 1 Replies View RelatedI have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net.
My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20
I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2)my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to go out to the internet. I think it has to do with the routes. [code]
I have been looking into this for a while and I can't seem to figure out why my 2nd vlan is not able to connect properly to the net. My switch has 12 ports where my devices connects directly, they are all on Vlan 1 and they all work perfectly. on Port 12 I have a dlink router that is connected to a cable modem. the dlink router has an Ip address of 192.168.0.20,I created a second vlan (vlan2) and enabled dhcp relay on it. then I assigned port 9 on the switch to (vlan2),my laptop which is connected to port 9 seems to get an ip address fine and able to ping only some devices on my network (vlan1) and is not able to,go out to the internet.
View 3 Replies View RelatedI'm having trouble setting up SSH on my new Switch.
no aaa new-model
aaa authentication login default local
ip domain-name king.local
[Code].....
I would like to be able to use Vlan 10 192.168.155.1 for SSH remote management.
i try to implement layer 2 qos in 2960. when i complete to configure the switch, i want to test the qos.PC1 conect to switch port 1,PC2 conect to switch port 2 . PC1 is source teminal. i use skydata.exe and FTP for the test.
when use the skydata ,the PC2 speed can reach 10mbps.when use the FTP , the PC2 only can reach 1.2mbps. why?
I can use Putty to SSH into my new switch (Directly connected to my laptop with ethernet cable), but I cant log into my switch.
Sent username "admin"
admin@192.168.251.1's password:
Access denied
It doesnt like my password, but I have only set 1 password (king) on this switch. I've configured 3 other switches with SSH and had no problem. Been trouble shooting for awhile and It'd be great if I could have a 2nd set of eyes take a peek, Also, my running config is attached.
I had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong.
View 3 Replies View RelatedDoes the port adaptor PA-MC-2E1/120 work with the Catalyst Switch 6506E (Sup Engine: 720-3B)? We have bought a Enhanced FlexWAN card for this port adaptor.I read through the cisco website and seem to get confusing answers whether they are compatible.
View 1 Replies View RelatedI am using a catalyst 2970 switch for 2 vlans. Corporate data and a separate VLAN for backups. What I want to do is create an LACP etherchannel to the switch and also trunk these ports so the server is part of both VLANS.Due to fact that some of these servers are on totally separated networks, they really shouldn't be able to talk to the backup server. Creating the VLAN for backups works to achieve this. I plan to create inbound ACLs on each port to allow only the ports and IPs for the backup network and allow everything we need for corporate data.I read somewhere that you can't have ACLs on an etherchannel and I just want to get it all straightened out. I notice I can't add an access group to the port-channel itself but I can on the port- channel member ports. Is this all I need to do or does this not work?
View 1 Replies View RelatedI had an old Cisco Catalyst 2948G switch that I have not used in about 7 years down in my basement. I powered it on and went through the process of clearing out the configurations, and I got to a point where one of the commands to clear out the config asked me to install jumpers for "ROM" and "ERASE". There is a third jumper labeled "NO BOOT". They are numbered J6, J7, & J8 respectivelyI found the jumpers inside and put the jumpers on them and ran the command expecting it to remove any old configurations I had on the switch and bring it back to factory state, but I was wrong. This switch runs CatOS, not IOS.When power is applied to the switch, the fans turn on as normal, but no LEDs are lit on the front. There are green LEDs lit next to the jumpers inside, but that is all. I am not able to get any response from it on the console at all anymore.The LEDs that are lit green inside are labeled "CR5" and CR6".
View 2 Replies View RelatedI have inhereted a network in a school that is using a Cisco Catalyst 500 series switch. Previously, it appears that this switch was never managed (just plugged in and using it's default configuration). I am trying to change that and be able to control the switch using the Network Assistant or just the web-based device manager. I understand that you cannot perform the initial configuration with anything past Windows XP, because the broadcast flag setting past XP causes an issue where the IP address of the management computer is assigned but not the default gateway. Despite this, I am still unable to connect to the switch for management purposes. Here is a list of the steps I have taken, all of which have been unsuccessful:
1) I tried using a computer running Windows XP. The same issue occurred. It was assigned an IP address from the switch but did not get a default gateway. It was unable to access what should have been the default IP of the switch; 169.254.0.1
2) I tried it in Windows Vista by editing the registry to turn broadcasting off. It still did not work.
3) I tried it in Windows 7. Still no luck.
4) In all 3 operating systems, I tried using the "Advanced" setting in the TCP/IP configuration to add a default gateway of 169.254.0.1 to no avail.
[URL]
is it possible to run a Catalyst 4500 as pure Layer 2 Switch, i.e. disabling "ip routing", but still managing the switch via Fa1, i.e. the defautl mgmtVrf vrf ?I tried the following:
!
no ip routing
!
interface FastEthernet1
ip vrf forwarding mgmtVrf
ip address 192.168.1.1 255.255.255.0
!
ip route vrf mgmtVrf 0.0.0.0 0.0.0.0 192.168.1.254
ip default-gateway 192.168.1.254
I was not able to reach the Switch even from the same subnet. Only after enabling ip routing I could manage the Switch. I haven't found any command to set ip default-gateway for a vrf. Any workaround to keep routing disabled, but still manageable via VRF?
Currently we have cisco 4503 switch in one of our location without redundancy which servers below,
300 user (desktop & ip phones)
5 vlans
15 access switches are connected
one L3 connectivity.
Actually i want to understand is it really necessary to have 4503 or we can go for 4900 series as we are planning to have redundancy in distribution segment.
Which is the best L3 switch in the above scenario and how to measure the overall performance of the current 4503 switch...