Cisco Switching/Routing :: 3750G Replacing VTP Server Switch
Apr 8, 2013
I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs. These 2 current switches are the VTP server for a small domain. I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?
View 7 Replies
ADVERTISEMENT
Dec 6, 2012
We have sup engine 6L(WS-X45-SUP6L-E) on two 4506 switch. both switches connected in LAN (HSRP primary and Secondary).
We are going to replace it with Sup7LE. What is the best procedure to get this done with minimal outage?Any other important thing to be noted ? Note : We have Lincence for SUP 7LE
View 2 Replies
View Related
Jul 27, 2012
I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
Below is main part of the router config:
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending
[code].....
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?
View 4 Replies
View Related
Jun 18, 2012
I have a supervisor blade, (VS-S720-10G-3C), in a 6513 that is faulty and needs replaced. Do I need to replace the IOS on the new supervisor blade to make sure it is the same as the IOS image that is on the Active supervisor module, or will it synchronize automatically?
In the synchronization process, the active supervisor engine checks the standby supervisor engine run-time image to make sure that it matches its own run-time image. The active supervisor engine checks three conditions:
#
•If it needs to copy its boot image to the standby supervisor engine
#
•If the standby supervisor engine bootstring needs to be changed
#
•If the standby supervisor engine needs to be reset
I was reading the above documentation that mentioned the active supervisor should copy the image if it detects a newly installed standby supervisor blade with a different image, is this correct or was it referring to synchronizing the configuration file?
View 3 Replies
View Related
Oct 8, 2012
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
View 2 Replies
View Related
Jan 2, 2013
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies
View Related
Jun 17, 2012
have one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
View 2 Replies
View Related
Feb 7, 2011
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
View 9 Replies
View Related
Mar 7, 2013
I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies
View Related
Apr 14, 2012
if we can stack the 3750G switch with a 3750X switch ?
View 7 Replies
View Related
Apr 23, 2013
I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
View 2 Replies
View Related
Feb 21, 2013
The two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies
View Related
Mar 30, 2013
i am not able to add new 3750G switch into existing domain even after the domain name is correct and unable to authenticate with tacacs.
View 5 Replies
View Related
Nov 3, 2011
I am about rip and replace my current 3750G stack with a 3750X stack. I have trunked over vlan and vtp info and implemented a config so it should be ready to go other then moving cables onto it. However one thing I want to correct with our current setup is that the root bridge on our vlans including vlan 1 is on a separate set of switches that we control, however I would like this new stack to be the root bridge for all of our vlans. It will be the central set of switches that all other switches trunk into. I have pre-set higher spanning-tree priorities for each vlan on the new stack so I expect as I move lines into it that the tree will be re-calculated with it as the root bridge. I've ensured that there are no root guards on any of the other switches trunks and priorities are all at default levels for each vlan. Should I enforce root guard on the trunk interfaces of the new master stack? Most of the trunks are port-channels to the other switches - do I need to set root guard on the Port channel interface or on the individual ports that make up the Port channel? On both? Any other recommendations in regards to implementing spanning-tree with the new stack? I know using port channels eliminates a lot of potential for loops but not every trunk is and I'd still like to have spanning-tree on.
View 1 Replies
View Related
Feb 19, 2013
I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
View 15 Replies
View Related
Apr 22, 2012
Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies
View Related
Nov 24, 2011
I try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 Replies
View Related
Mar 30, 2013
I am cascading one new switch 3750G (int Gi1/0/1) with an existing 3750G (int fa1/0/26) switch.. But the interface fa1/0/26 goes in err-disable state even after NO SH.. also i have diable Spanning treebpdu guard and disable spanning tree portfast. But still the issue is not resolved.
View 6 Replies
View Related
Jan 23, 2013
I have faced a problem with configuring Cisco 3750G series switches as Sever farm switches with redudance.
servers have 2NIC (1GBps) and both are bridged for redundant connections.In both switches all ports get green coluor except one port on Secondary SW. I saw some Spanning tree block port status on that switch.when i type Show cdp neghbor command on switch i can see other switch through a server connected port. Also Spannig tree root bridge election is occured through that port . Simply i need to configure both switches to pass traffic through there uplinks them selves.. but it seems like Secondry switch pass its traffic through primary switch ( i think according to STP ) usinginterconnection of bridge port of a server. [code]
View 1 Replies
View Related
Dec 7, 2011
I am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies
View Related
Feb 29, 2012
I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
View 19 Replies
View Related
Jan 15, 2012
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
View 1 Replies
View Related
Oct 29, 2011
How to replace a defective redundant sup. I read on several articles that inserting new redundant sup should not be an issue as the active sup will always send its configuation to the standby. We are running SSO on the Sup720. Should I switch it to RPR before I install the redundant sup? I read a case wherein they switched it to RPR from SSO before inserting the new redundant sup. My concern is the IOS mismatch since Cisco doesn't always send the same IOS on RMAs.What I am planning is this.
1. Save/Backup configuration
2. Remove the redundant sup on slot 8 (since it is a 6513)
3. Insert the new redundant sup on slot 8.
4. Check if all the configurations were synced from slot 7 to slot 8.
5. Copy the IOS from sup-bootflash to slavesup-bootflash. (if the IOS are not the same)
6. Check show bootvar to see if the boot variables are correct.
7. If bootvar is the same, reload slot 8 to boot the new IOS.
Is this a good plan or am I missing something? I am worried with this document if the redundant sup has a different software. If i insert the card in slot8, according to Cisco, it will revert to RPR. If slot 8 boots and it has a different OS, then slot 7 will switch to RPR even if it's active. Would I still be able to access the slavesup-bootflash of slot 8? Is it going to boot 100%? I read that doing a force switchover will cause a flip and RPR would cause the line cards to reinitialize and I don't want that. Well I am not going to do a force switchover since i want slot7 to be active and retain slot 8 as hot.
View 3 Replies
View Related
Nov 21, 2011
I am replacing a faulty sup720 on a 6513. It s the backup/hot not the active sup. It has the same IOS on it. Is it correct that all I need to do is remove the faulty and replace it with the new sup and do a wr mem? Fromwat I have read their should be no down time all connectivity should remain stable?
View 6 Replies
View Related
Jul 2, 2012
I decided recently to switch out our border router (1841 12.4 advsecurity) with a shiny new 1941 (15.2 SEC/K9) as the CPU upgrade was needed.The core below acts as a VPN end point to various other remote offices we have, all of which have a similar network design at each end (and all entirely managed by me). All of these are still running 1841's with 12.4 advsecurity on them as well. These are all GRE tunnels with ipsec procection on them (not crypto maps). [code]
Everything else works fine (NAT, route-maps etc), it's just these IPSEC/isakmp tunnels that are not playing ballIt's definitely not an ARP issue (all arps were cleared) and ICMP appears to work fine (ie, I can ping the remote tunnel's public IP endpoint from the core using the loopback for that tunnel as the source). I am suspecting it's something strange with the stateful firewall config, but I did try and apply ipsec and isakmp-msft to the ip inspect list, with no success.
View 1 Replies
View Related
Mar 10, 2013
In my MDF I have a 4stack of the WS-3750-48P switches. Is it possible to replace one with a C3750X48PF-S with out causing any issues? Or would it be better to just have 3 stacked and trunk this one to the core 4506. Keeping in mind I bought this one to expand the port number for one of our remote offices.. I would hate to send them the gig switch when there isn't as much usage..Besides if I can get my CFO on this switch he might authorize me to replace the rest... He is reticent to believe it makes really all that much of a difference.
View 2 Replies
View Related
May 7, 2013
I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.
View 1 Replies
View Related
Jul 25, 2012
We currently have an environment with a 4507 as the core switch connected to four stacks of 3750e's in the wiring closets. A pair of Nexus 5548UP's also hangs off the 4507, but at the moment more or less dedicated to a certain purpose..The 5548UP's have the L3 daughter card installed.
My question is: Can a pair of Nexus 5548UP's do a C4507's job? Would we be able to decomission the 4507 and replace with the existing 5548UP's + FEXes?
View 1 Replies
View Related
Dec 9, 2012
We are planning to implement the 6509-E with two Sup 2Ts and a few 48 ports switches. We also want to make this the router for our network and replace the 7206VRX.
View 5 Replies
View Related
Mar 20, 2012
when replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?
View 2 Replies
View Related
Jun 3, 2013
I was wondering what general steps might be taken in order to "replace two(2) 3750 (stacked) with one (1) 3750X - Server Access". General steps and what I might have to do configuration wise. I know i'm copy pasting the existing configs into the new switch, but are there any caveats?
View 5 Replies
View Related
Feb 7, 2012
I have two 3750X in a stack. Each 3750X has one 10Gb uplink to primary core1 and one 1Gb uplink to backup core2 configured in 2 etherchannel groups. The member switch has bad ports, so I need to replace it. I have spare 3750X unit. Is it possible to connect the spare unit to the stack and then move the RJ-45 cables from the member with bad ports to the new member? That way I can minimize servers downtime to just a few seconds..If that would work, then the last step would be to move the 10Gb networking module from old member to the new one, as well as the secondary PSU. Is it doable? Also according to the documentation, all I need to add new member is matching IOS version, correct?
View 1 Replies
View Related
Apr 17, 2013
I want to replace an existing 3560 Switch with another switch of the same exact model and IOS. However, this switch that needs to be replaced is the VTP Server of my LAN at this location. When I replace the switch I will just use the same exact running config but I'm concerned about the vlan.dat file. Do I need to copy that file over to the new replacement switch and if so, what is the best way to do that?
View 5 Replies
View Related
