Cisco Switching/Routing :: Unable To Add New 3750G Switch Into Existing Domain
Mar 30, 2013i am not able to add new 3750G switch into existing domain even after the domain name is correct and unable to authenticate with tacacs.
View 5 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 3750G Switch With PBR With IP SLA Not Working?
Oct 8, 2012I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
Cisco Switching/Routing :: Switch 3750G-12S-S Configuration?
Jan 2, 2013I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies View RelatedCisco Switching/Routing :: Switch 3750G Stack
Jun 17, 2012have one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
Cisco Switching/Routing :: 3750G / Errors In Switch Log
Feb 7, 2011I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
Cisco Switching/Routing :: 3750G Replacing VTP Server Switch
Apr 8, 2013I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs. These 2 current switches are the VTP server for a small domain. I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?
View 7 Replies View RelatedCisco Switching/Routing :: 3750G - How To Bypass Old Configuration In Switch
Mar 7, 2013I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies View RelatedCisco Switching/Routing :: Stack 3750G-12S-S With 3750X-48T Switch?
Apr 14, 2012if we can stack the 3750G switch with a 3750X switch ?
View 7 Replies View RelatedCisco Switching/Routing :: IOS Upgrade Procedure Switch 3750g?
Apr 23, 2013I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
Cisco Switching/Routing :: 3750G / Switch Loses Connecting To Distribution SW
Feb 21, 2013The two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies View RelatedCisco Switching/Routing :: 3750G Spanning Tree On New Switch Stack
Nov 3, 2011I am about rip and replace my current 3750G stack with a 3750X stack. I have trunked over vlan and vtp info and implemented a config so it should be ready to go other then moving cables onto it. However one thing I want to correct with our current setup is that the root bridge on our vlans including vlan 1 is on a separate set of switches that we control, however I would like this new stack to be the root bridge for all of our vlans. It will be the central set of switches that all other switches trunk into. I have pre-set higher spanning-tree priorities for each vlan on the new stack so I expect as I move lines into it that the tree will be re-calculated with it as the root bridge. I've ensured that there are no root guards on any of the other switches trunks and priorities are all at default levels for each vlan. Should I enforce root guard on the trunk interfaces of the new master stack? Most of the trunks are port-channels to the other switches - do I need to set root guard on the Port channel interface or on the individual ports that make up the Port channel? On both? Any other recommendations in regards to implementing spanning-tree with the new stack? I know using port channels eliminates a lot of potential for loops but not every trunk is and I'd still like to have spanning-tree on.
View 1 Replies View RelatedCisco Switching/Routing :: Upgrading From Router 2800 To L3 Switch 3750G?
Feb 19, 2013I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
Cisco Switching/Routing :: Can Stack 3750G-12S-S Switch With 3750E-24TD-S
Apr 22, 2012Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies View RelatedCisco Switching/Routing :: Connect Two Switch Catalyst 3750G Without Success
Nov 24, 2011I try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 Replies View RelatedCisco Switching/Routing :: 3750G / (int Fa1/0/26) Connected To Switch / Goes In Err-disable State
Mar 30, 2013I am cascading one new switch 3750G (int Gi1/0/1) with an existing 3750G (int fa1/0/26) switch.. But the interface fa1/0/26 goes in err-disable state even after NO SH.. also i have diable Spanning treebpdu guard and disable spanning tree portfast. But still the issue is not resolved.
View 6 Replies View RelatedCisco Switching/Routing :: 3750G-12s-s Switch Reboot When Power Source Restore From RPS To AC?
Dec 7, 2011I am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies View RelatedCisco Switching/Routing :: 3750G - Adding Additional Switch And Making It Stack
Feb 29, 2012I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
Cisco Switching/Routing :: Adding A New Switch In Existing Two 3750 Stack
Mar 25, 2012in our network we were using three 3750-48-s switches with stacking one of the switch due to some hardware failure power problem,
now i want to add a new switch 3750-48-s in the existing Stack two switches , the old two switches ios version is = 12.2(25r)SEC the new Catalyst 3750 io verion is = 12.2(35)SE5
how to add this switch in the existing two stack switches , with documentation
Cisco Switching/Routing :: Adding 3750 Switch To Existing Stack?
Nov 23, 2011I am looking to add a new 3750 Switcch to an existing stack shown below
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
2 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
3 26 WS-C3750-24P 12.2(35)SE5 C3750-IPBASE-M
[code]....
I have looked on notes to add a switch to an existing stack and haven’t identified answers on how the IOS will be affected on the new switch – will it downgrade to the current stack version or will the current stack upgrade to its version. At this moment in time I would prefer if the new switch IOS downgraded to the current stack IOS version.The new switch is a 3750V2 – will this affect how it joins the stack?The new switch has the image of IPBASEK9-M – again will this affect how it joins the stack?
Cisco Switching/Routing :: Adding New Switch To Existing C3750x Stack?
Dec 6, 2012I am having an issue with adding a c3750x switch to an existing switch stack Currently there is 2 x WS-C3750X-48P and I am trying to add another WS-C3750X-48P to this switch I have cabled the switch to the stack using the stack cables and added the command to provision the switch on the exisitng stack. However when I turn the switch on it just goes on its own stack.
I noticed the new switch had a later version of IOS so have downgraded this to the same version as the other switches but still no joy Here is the sh ver from the exisitng stack
uptime is 4 weeks, 4 days, 23 hours, 30 minutes
System image file is "flash:/c3750e-universalk9-mz.122-53.SE2/c3750e-universalk9-mz.122-53.SE2.bin"
License Level: ipbaseLicense Type: PermanentNext reload license Level: ipbase
cisco WS-C3750X-48P (PowerPC405) processor (revision A0) with 262144K bytes of memory.Processor board ID FDO1448Z0FJLast reset from power-on21 Virtual Ethernet interfaces1 FastEthernet interface156 Gigabit Ethernet interfaces6 Ten Gigabit Ethernet interfacesThe password-recovery mechanism is enabled.
[code]....
Cisco Switching/Routing :: Adding Switch To Existing Stack 3750
Oct 16, 2012I am attempting to add and Catalyst 3750 - 12 port Gigabit switch to an existing stack of 3750 48 port switches (non-X fabric). I am not sure how to proceed. These are the two questions/thoughts I have. Any additional perspective I should have before proceeding.
What kind of configuration should I apply to the Gig switch before adding it to the stack?I am sure I will need to assign priority to the new switch, ideally, it will act as master.
Cisco Switching/Routing :: Catalyst 3750G / WS-3750G-48PS Memory
Jan 15, 2012Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
Cisco Switching/Routing :: 3560X-24T-L Joining A Switch To VTP Domain
Sep 28, 2012I am trying to join a Cisco Catalyst 3560X-24T-L to an existing VTP domain, my question is what configurations should I do to this switch?I have already gave it a hostname, setup passwords, enabled telnet, created a management address on port g0/24.I would like it to be on VLAN 13, is this done from my server switch, or done on the new switch?
View 10 Replies View RelatedServers :: Add A PC With Existing Domain Network?
Feb 25, 2011We have purchased a new PC(OS, Windows XP2002, SP2). Now i want to add it with existing Local Area Network which is domain networking. Now how can i add the computer in that network? we use Oracle data base on it. i want to know that how this will work just like other clients on network. i know the LAN without domain network. i add it with network. it is now appear the workgroup. but when i access any client on network, then it cann't do any action, and replies access denied and not access any client c$ drive.
View 2 Replies View RelatedCisco Switching/Routing :: 6509-E / VSS - Unable To Set Switch Number
Aug 28, 2012I have a 6509-E chassis that was prevoius in a VSS configuration. Due to some VSL failures I had to cobvert it to a standalone chassis but would like to bring it back to a virtual system.
Whenever I try to convert it by using the command "switch convert mode virtual" I get the msg %Please configure local switch number first". After doing so by entering the CLI cmd "switch set switch_num 1 local" I still get the same message.
Cisco Switching/Routing :: Unable To Mange 500 Catalyst Switch
Jun 8, 2013I have inhereted a network in a school that is using a Cisco Catalyst 500 series switch. Previously, it appears that this switch was never managed (just plugged in and using it's default configuration). I am trying to change that and be able to control the switch using the Network Assistant or just the web-based device manager. I understand that you cannot perform the initial configuration with anything past Windows XP, because the broadcast flag setting past XP causes an issue where the IP address of the management computer is assigned but not the default gateway. Despite this, I am still unable to connect to the switch for management purposes. Here is a list of the steps I have taken, all of which have been unsuccessful:
1) I tried using a computer running Windows XP. The same issue occurred. It was assigned an IP address from the switch but did not get a default gateway. It was unable to access what should have been the default IP of the switch; 169.254.0.1
2) I tried it in Windows Vista by editing the registry to turn broadcasting off. It still did not work.
3) I tried it in Windows 7. Still no luck.
4) In all 3 operating systems, I tried using the "Advanced" setting in the TCP/IP configuration to add a default gateway of 169.254.0.1 to no avail.
[URL]
Cisco Switching/Routing :: 3560 - Unable To See Entry For Switch
Oct 30, 2011I have configured a new switch 3560 switch and connected to 4500 switch and formed a trunk connectivity.Now the issue i am facing is when i do a SH CDP NEIGHBOUR from 3560 switch i am able so see 4500 swries switch but at the same time when i do SH CDP NEIGHBOUR form 4500 series switch i am not able to see the entry for 3560 switch.But i am able to telnet the new switch with out any issues
View 11 Replies View RelatedProtocols / Routing :: TEW-692GR Unable To Get To Domain From Outside Network
May 21, 2012We just had a TEW-72GR router fail and replaced it with a TEW-GR. Now I am unable to get to my domain (mydomain.net) from outside the network. Inside the network, all appears to be fine. I can enter that address and get to the site with no issues.We use SBS 2008 with windows 7 clients.All clients can get out to the web, we can send and receive emails, but I can not access the domain.
View 2 Replies View RelatedCisco Switching/Routing :: 2960s - Unable To Access Lite Switch
Nov 9, 2012Unable to access switch from outside the local network. Can get to all routers and PC's
View 2 Replies View RelatedCisco Switching/Routing :: Unable To Connect To Switch Over A Cat5 On First Port
May 7, 2012Im not going to lie, I'm pretty much a beginner when it comes to switches. I have recently purchased a second hand 3512 XL which I have managed to connect to via PuTTY and the console cable. I have familiarized myself with access privileges and resetting passwords and locating the IP address, etc.
I am trying to connect the switch to Cisco Network Assistant however I am unable to connect to the switch over a cat5 on the first port (nothing else is on the network, just a server directly to the switch). I have tried pinging the switch from my server, and similarly I have tried pinging the server from the switch and each time there is 100% fail rate.
Cisco Switching/Routing :: 2960S Unable To Connect To Core Switch
Sep 21, 2012I have a problem with extending the LAN on a client site . They are looking to extend the LAN with a 2960S-series switch. Already in place is a 4510 switch which the 2960 is connected to via fibre. The 2 switches are both set up but there is no connectivity as I cant ping between them or anything. The management VLAN on the 2960 shows line up, protocol down, which I believe means the VLAN is enabled but there is a form of physical mismtach on the ports. I have attached the configs of both switches. I feel it might be a problem with GBIC module compatibility. The SFP installed on both ends of the switch are GLC-SX-MMD. On the 4510, the SFP sits in a twingig converter (CVR-X2-SFP) but there is no light on it at all when the cables are plugged in.
View 40 Replies View RelatedCisco Switching/Routing :: Unable To Use DHCP In 2960 And Unmanageable Switch?
Nov 1, 2012I am having 2960 switch and one port is configured with a VLAN and connected with an unmanageable switch and further one more unmanageable switch was connected to the primary unmanageable switch…
The topology will be 2960 switch -> unmanageable Switch -> unmanageable -> PC connected
The issue I am facing most of the PC are getting IP addresses through DHCP server and very few 5 or 6 PC’s out are not getting the IP from DHCP server.If I switch of the switch and switch on the issue is resolved for those and it will raise for some other PC’s.
Cisco Switching/Routing :: 2960 / Unable To Access Switch Via Console?
Dec 27, 2012I have 2960 switch and i can't access it using my console cable .I can access other switches in my network ( 3560 & 2960 ) but i can't access only this switch.may be the console port in the switch damaged? or it's a bug ?? !!! although the switch is worked normally.
View 11 Replies View Related