Cisco Switching/Routing :: 3750G / Errors In Switch Log
Feb 7, 2011
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
View 9 Replies
ADVERTISEMENT
Feb 27, 2013
I currently have a stack of 3750G switches with a cross stack etherchannel connected to a 3750E stack in the distribution layer.The 3750G stack is running 15.0-2SE IP Base. I began noticing the Mac flap issue when I was Re-enabling dot1x on the switchports. As first I thought dot1x maybe have contributed to this so I removed it from the stack temporarily.I am still seeing Mac flap logs usually when a machine reboots or re-connects back to the network. These are all wired desktops.I started looking at the etherchannel configuration which is using LACP. The 3750E stack looks fine with all ports in mode active. On the problematic 3750G stack I noticed 3 of the ports in the etherchannel set to mode active and 1 port set to mode passive. The port shows as bundled but I can't imagine this is ok.The only other difference on this one port is there is no mls qos commands like on the other 3 interfaces in the port channel.I mainly need to know what the Mac flapping is about. Whether it is a bug or related to the current etherchannel configuration.
View 9 Replies
View Related
Oct 16, 2012
We have a stack of 4 Cisco WS-3750G-24TS with Sw Version 12.2(52) SE and giving weird errors:-
-Traceback= 17211C8 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:48 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:50 AEDT: %SYS-3-CPUHOG: Task is running for (2098)msecs, more than (2000)msecs (8/6),process = SNMP ENGINE.
-Traceback= 172108C 17211CC 16FA4C0 16FA4FC 18625E4 18608D4 286A850 283E6FC 282EDF4 2859BBC 1B2EDA8 1B25878
Oct 17 22:26:51 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.7
Oct 17 22:26:53 AEDT: %SNMP-3-CPUHOG: Processing GetBulk of lldpRemEntry.6
Oct 17 22:26:53 AEDT: %SYS-3-CPUHOG: Task is running for (2097)msecs, more than (2000)msecs (1/1),process = SNMP ENGINE.
What are these errors is this a bug in the IOS
View 1 Replies
View Related
Jun 22, 2012
One of my wi-fi site having 2nos cisco 2950 switchs. in that network some D-link unmanageble swithes also there and access points also connected to cisco switchs and D-link switchs.after one or two days i am not able to connect the wi-fi, then i need to restart the access point then only wi-fi is working fine.I upgraded the latest ios also.I connected some access points to the cisco switch ports, those ports are showing crc error messages like below. [code]
View 18 Replies
View Related
Oct 8, 2012
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
View 2 Replies
View Related
Jan 2, 2013
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies
View Related
Jun 17, 2012
have one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
View 2 Replies
View Related
Apr 8, 2013
I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs. These 2 current switches are the VTP server for a small domain. I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?
View 7 Replies
View Related
Mar 7, 2013
I am having an issue bypassing a switch 3750G series. How i can bypass the old configuration in the switch.i have tried the CTRL+BREAK at startup but it wont work.
View 2 Replies
View Related
Apr 14, 2012
if we can stack the 3750G switch with a 3750X switch ?
View 7 Replies
View Related
Apr 23, 2013
I am looking few information on IOS up-gradation for the switch WS-C3750G-48TS-S . I loaded new Image on the flash and current flash and sh boot as below
Switch#sh flash
Directory of flash:/
2 -rwx 8859636 Mar 1 1993 00:08:14 +00:00 c3750-ipservicesk9-mz.122-37.SE.bin
3 -rwx 556 Mar 1 1993 00:02:38 +00:00 vlan.dat
4 drwx 64 Jan 9 2012 03:17:56 +00:00 crashinfo_ext
5 -rwx 5768 Apr 24 2013 04:25:28 +00:00 private-config.text
[code]...
1) I would like to set boot sytem parameter for the new IOS and secondary old IOS as well is below command works??? if IOS not coming up with new one 12.2.58 is it boots with old 12.2-35 ?
boot system flash:c3750-ipservicesk9-mz.122-58.SE2.bin;flash:c3750-ipbase-mz.122-35.SE5
2) If I set only boot system flash:c3750-ipservicesk9-mz.122-58 , if new image corrput swicth will check valid image and boot up with old image ?
3) If switch went to room1 switch mode and still I have valild running IOS c3750-ipservicesk9-mz.122-37.SE.bin at flash memory, how to restore with old image
View 2 Replies
View Related
Feb 21, 2013
The two stacked Cisco 3750G Access switches on a particular floor in my coy just lost connectivity to the distribution Switch this morning. This meant that all Users connected to it couldnt connect to the Internet nor access local network resources.I couldn't ping the Switch IP, I couldn't also access the Switch via Console port. Each time I tried to gain access via the console port, I keep getting "Authentication Failed" message.What should I do next? How do I gain access to the Switch?
View 1 Replies
View Related
Mar 30, 2013
i am not able to add new 3750G switch into existing domain even after the domain name is correct and unable to authenticate with tacacs.
View 5 Replies
View Related
Nov 3, 2011
I am about rip and replace my current 3750G stack with a 3750X stack. I have trunked over vlan and vtp info and implemented a config so it should be ready to go other then moving cables onto it. However one thing I want to correct with our current setup is that the root bridge on our vlans including vlan 1 is on a separate set of switches that we control, however I would like this new stack to be the root bridge for all of our vlans. It will be the central set of switches that all other switches trunk into. I have pre-set higher spanning-tree priorities for each vlan on the new stack so I expect as I move lines into it that the tree will be re-calculated with it as the root bridge. I've ensured that there are no root guards on any of the other switches trunks and priorities are all at default levels for each vlan. Should I enforce root guard on the trunk interfaces of the new master stack? Most of the trunks are port-channels to the other switches - do I need to set root guard on the Port channel interface or on the individual ports that make up the Port channel? On both? Any other recommendations in regards to implementing spanning-tree with the new stack? I know using port channels eliminates a lot of potential for loops but not every trunk is and I'd still like to have spanning-tree on.
View 1 Replies
View Related
Feb 19, 2013
I wan to migrate from a router 2800 to L3 switch 3750G , the thing is that we have several vlans and we use a router sometimes with each interface configure with correspoinding vlan subnet ip to route traffic between vlans there is no static or dynamic routing only directly connected interfaces on router routing traffic to each other ?How would i configure a L3 switch interface for simillar functionality , below is my current router configuration
!
ip domain name yourdomain.com
multilink bundle-name authenticated
!
vtp mode transparent
[code]...
View 15 Replies
View Related
Apr 22, 2012
Can we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies
View Related
Nov 24, 2011
I try to connect two switch Catalyst 3750G without success.switch1 (192.168.2.10 vlan 2) <=> (192.168.2.11 vlan2) switch2.I use this configuration for swich1 [code]
View 23 Replies
View Related
Mar 30, 2013
I am cascading one new switch 3750G (int Gi1/0/1) with an existing 3750G (int fa1/0/26) switch.. But the interface fa1/0/26 goes in err-disable state even after NO SH.. also i have diable Spanning treebpdu guard and disable spanning tree portfast. But still the issue is not resolved.
View 6 Replies
View Related
Apr 15, 2010
I have two 3560G 24 port switches. Each of them connects to some 3560G or 2950 switches. Trunks between 3560G are set as 1000/full. Trunks between 3560G and 2950 are set as 100/full. show int status also shows the interface negotiation is 100/full for trunks between 3560G and 2950. The issue is I keep getting outdiscard errors in trunks between 3560G and 2950. At 2950 switches, I see Recv-errors too. I checked all the trunks traffic. They are totally not high. Only serveal mbps. Most time even lower than 1mbps.
I googled this kind of issue online. I see it could be possibly caused by high volume traffic higher than the capacity. But it appears the traffic there is not high enough to cause this kind of issue. Is there any possiblity that could cause this problem?
The below is 3560G trunk configuration for 2950 switch
interface GigabitEthernet0/10 switchport trunk encapsulation dot1q switchport trunk allowed vlan 1-122,124-4094 switchport mode trunk speed 100 duplex full srr-queue bandwidth share 10 10 60 20 queue-set 2 priority-queue out mls qos trust cos auto qos voip trust
the trunk configuration at 2950 switch: interface FastEthernet0/24 switchport trunk allowed vlan 1-122,124-4094 speed 100 duplex full
View 16 Replies
View Related
May 19, 2013
SW1#show interfaces fastEthernet 0/14 counters errors
Port Align-Err FCS-Err Xmit-Err Rcv-Err UnderSize
Fa0/14 6682 140364 0 306468 0
Port Single-Col Multi-Col Late-Col Excess-Col Carri-Sen Runts Giants
Fa0/14 0 0 0 0 180103 0 2798
[code]....
View 5 Replies
View Related
Dec 7, 2011
I am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies
View Related
Feb 29, 2012
I currently have Cisco 3750G which is currently live and active and fully populated and only have remote access.
I have an additional same switch which I would like to stack. My initial plans were to have 2 GIbit etherchannels, but I came across the option to Stacks both switch with each other.
When I do a show switch on the live switch its set as a Member: [code]
I would like to add the new switch to the stack without losing the config for the switch which is live. I understand that the highest priority of the switches becomes the Master but as the live switch is Priority 1, would chancing this affect the switches config, or would it lose connection at all?
Also when I plug in the new switch and it reboot how do I ensure it becomes the slave without rebooting the live switch?The cables on the switch do they have to go to port1 on the live switch and port 1 on the new switch or can they be port 1 and port 2?
View 19 Replies
View Related
Jan 15, 2012
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
View 1 Replies
View Related
Mar 21, 2012
I got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
View 4 Replies
View Related
Mar 4, 2012
I've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
View 7 Replies
View Related
Nov 8, 2012
I have a couple of 3750G-24T-E switches running IOS 12.2 I would like to upgrade to IOS 15.x. Is this possible? Where do I find some information on the required licenses and costs? I must admit that the cisco search function did come up with a few pages but i was not able to extract the required information. I have not used the new software activation features yet.
View 1 Replies
View Related
Apr 18, 2013
i have a standalone SUP720, no traffic is passing through it. only one port connected for remote telnet, its kind of backup device.today i checked its log, and there are some wiered message.is it a software bug or my SUP has gone bad? [code]
View 24 Replies
View Related
Jan 9, 2012
today I witnessed a cisco n5k that stopped playing fair. For a yet unkown reason several interfaces started to show output errors all begining within the same second. While i instantly thought this would be a wiring issue I began to ask myself what an output error actually means. Google usually brings up output drops, not regular output errors. So what is it and how can a 10G fiber interface even detect that there is a problem without receiving what it was sending?
View 2 Replies
View Related
Jun 7, 2012
I've got a requirement to do Inter-VRF routing (need MP-BGP) using a private AS Number on a stack of 7 x 3750G's, my question ultimately is the performance overhead of doing such a change.
The stack will have no more than 300-400 routes even with the duplicates invoked from doing VRF leaking so I can't see much of an issue myself, we already have 2 VRF's and OSPF running in each VRF just don't have MP-BGP to do the VRF leaking.
Ultimately there will be about 4-5 VRF's (I know there's a Software limit of 26 VRF's on a 3750G).
View 3 Replies
View Related
Oct 2, 2012
I am trying to stack the following -
3750G 12S - 12.2.53(SE2 IP Services) Running EIGRP & OSPF
with
3x 3750X 48P-S - 12.2.53(SE2 IP Base License)
Doing some research, the IP Base does EIGRP on the 3750X, does it do OSPF?
If not I will have to get licence for the 3750X?
View 3 Replies
View Related
Nov 20, 2012
have 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
View 4 Replies
View Related
May 26, 2011
I have a 3750G and bought a new 3750X. It possible to stack these two together?
View 5 Replies
View Related
Nov 18, 2008
I have a 3750g on which I am trying to configure the ip policy route-map command on each of the vlan interfaces. However after entering the command it does not appear. I'm not sure what to do at this point. I have changed the SDM template to routing and I am running the IPServices image.
View 2 Replies
View Related
