have 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
can I make the stacking of these two switches WS-C3750E-48PD-SF and WS-C3750X-48PF-L. Both have universal IOS.
View 11 Replies View RelatedI have one 3750X with C3KX-NM-10GT, I need to interconnect using stackwise to 3750G-24TS. The 3750X needs IOS 15.0(1) to use C3KX-NM-10GT, and the latest IOS for 3750G-24TS is 12.2.55. How can I interconnect them using diferent IOS?
View 2 Replies View RelatedCan we stack a 3750G-12S-S switch with a 3750-E-24TD-S switch?
View 4 Replies View RelatedWe are experiencing output drops on our 3750G-12S (IOS 12.2.55).
I have monitored throughput with MRTG, but it doesn't seem that high compared to that the 3750G is supposed to handle 17.8 Mpps.
The 3750G's are stacked, running ospf, qos, multicast (IPTV) and etherchannel.Is the maximum throughput reduced by stacking or any of the other features?
I don't know if one can estimate what the maximum throughput is per ASIC or per port, but on one of the ASICs that is having drops the peak unicast load is 1.3 Mpps and multicast Mpps is 0.9 Mpps. Total ~2.2 Mpps.
This doesn't seem high at all and I don't understand why the drops are appearing. What I can do to find out the reason for these drops?
I am trying to stack a 3750g with a 3750x. At the moment they will not stack with their current IOS as the hardware version is mismatched.
According to various posts this is possible as long as the same IOS is in use. The following IOS are currently in use:
3750g - c3750-ipbaselmk9-tar.122-55.SE5
3750x - c3750e-ipbasek9-mz.150-1.SE3
I have tried to downgrade the IOS on the 'X' to 122-55.SE5 however, i get errors regarding firmware incompatibility.
I am unable to upgrade the IOS on the 'G' to 150-1.SE3, as the size of the IOS image is larger than the available flash (Version 15 IOS for the 3750G (c3750-ipbasek9-mz.150-1.SE3.bin) is 16,074,189 bytes whereas the 3750G has 16MB of flash memory or 15,998,976 bytes total which mean the IOS will not fit).
Has not actually stacked these devices successfully? I understand there may be license implications of upgrading to 15 but at the moment I just want them to stack!
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
just wonder if the Cisco Stack Wise 50CM Stacking Cable is freely available when purchasing Cisco Catalyst 3750G-48PS-E or we need to pay for it?
View 2 Replies View RelatedI need to use cisco 3750E switch on core. I want to know whether BGP is supported on this model or not?Currently i have c3750e-universalk9-mz.150-2.SE/c3750e-universalk9-mz.150-2.SE.bin" preinstalled. and i checked BGP is not supported on this IOS image.
View 7 Replies View RelatedQuick question here. Using 3750E series switches with multiple VLANS configured. These switches serve as our 'core'. I have SVIs configured for the different VLANs and add inbound ACLs in each of the SVIs to control traffic between VLANS. This switch also terminates a P2P Ethernet link which connects to our Colo facility. The port used for this is configured as an L3 port. I noticed today that I was able to send traffic across this L3 link that I thought should have been blocked by an ACL I had in place but it wasn't. So the traffic flowed from a port in say VLAN 20 across this L3 link (assigned with an IP address). Would this traffic flow not cause traffic to be checked against an ACL applied in the inbound direction on the SVI of VLAN 20 (int vlan 20)? Traffic does get checked when routing between SVIs. Why would it not get checked when routing between SVI and L3 interface?
View 2 Replies View RelatedI am in the process of upgrading our network switches and wondering if the .lic file will work with the new software or if I have to rehost for the move to 15.0. Its a remote site and I would like to get some solid info before I pull the trigger.
Also which IOS should I be upgrading to?
c3750e-ipbasek9-mz.150-2.SE.bin
or
c3750e-universalk9-mz.150-2.SE.bin
[Code].....
Can I get a stack cable longer then 3m?
View 1 Replies View RelatedWe're seeing "OutDiscard" error on a LAN switch connected to newly migrated Cisco IP phones. All the other error counters are clean except for the OutDiscard. (please see attached "show int count err" output.) [URL].
According to the link above, the common cause of such discards can be to free up buffer space.(Am I seeing a switch buffer issue?) How to identify/resolve the cause of the OutDiscard.The switch is 3750-E running c3750e-universalk9-mz.122-44.SE6.bin
I am seeing on my 3750E series switches (WS-C3750E-48TD). I have multiple VLANs configured on here, one which is used as a 'workstation' VLAN. I have an inbound ACL applied to the VLAN interface *(int vlan 50 to be exact). This list is admittedly long at roughly 6000 ACE's. Now I just recently installed these switches as they replaced some 4507R switches which we moved to our new centralized DC. Here is the issue I am having. This same ACL was applied to the same VLAN interface on the 4507s when they were doing the work of the 3750s. What I used to be able to do was actually edit the ACL by removing it with no ip access-list extended WS-In and then followed up by the ip access-list extended WS-In ......and the lines I wanted in the ACL. I know I could use the line numbers to edit the ACL but this worked OK for me. When I would do this on the 4507R, the ACL was still applied to the interface but traffic never seemed affected by the removal and re-adding of the ACL. I did this by copying and pasting the ACL into a terminal window. It seemed as though on the 4507 the ACL was not compiled until the entire thing was in loaded in and therefore traffic was not processed by the ACL until the load was done
View 3 Replies View RelatedI have a 3750E stackable swtch and I need to configure neflow on it. Are there any IOS versions that support netflow on the 3750E? Is there any possible to configure netflow on a 3750E? I do not see any netflow commands available on the switch?
View 2 Replies View Relatedwhat is difference between Cisco catalyst 3750e 48 and SF300-48p.
View 3 Replies View RelatedI have 3750E swiches with IOS v. 12.2(55)SE3. Couple servers connect to ths switch, after ping of IP this servers I can see mac addresses in mac address table.
For instance:
sw1#show mac address-table vlan 20
Mac Address Table
-------------------------------------------
Vlan Mac Address Type Ports(code)
---- ----------- -------- -----
When ip generate traffic to this server this mac address appear in table again on shot time (less than 10 seconds).
I had a lot of problems with TCAM table in the past and made changes in SDM ended whit that. But now want to be proactive and anticipate the problems in my TCAM table.
If the my template is "default desktop" they support a number of indirect IPv4 routes of 2k. I wanna know automatically by my management tools if this number reaches 1.9k.
That way I can take corrective actions before the problems starts on my network.
I have a RVS4000 connected to my cable modem which I use as my gateway, the IP address of the RVS is 192.168.3.254
I have a 2811 with 3 subinterfaces of which I can ping all of them from my PC which at the minute is in VLAN 1, the only network that can connect to the outside world is VLAN 1, how can I enable the other 2 vlans to connect to the internet?
My set-up details are
Router
interface FastEthernet0/0.1
description *** Data Network***
encapsulation dot1Q 1 native
[Code]....
After I added the 3rd 3750E to my stack on Sunday I can no longer save my configs with 'copy run start' or 'write mem':
#copy running-config startup-config
Destination filename [startup-config]?
Building configuration...
nv_done: unable to open "flash:/config.text.new"
nv_done: unable to open "flash:/private-config.text.new"
nv_done: unable to open "flash:/multiple-fs.new"[OK]
[code]....
my flash seems to have plenty of space:
57409536 bytes total (24203776 bytes free)
How to stack a set of these switches with the copper 5G SFP on these switches. We currently have 4 switches stacked with Cat5e jumpers between S1&S2. We want to stop using this stacking method and go to the SFP. What is the best way to do this. Live would be preferable but whatever is the safest method is the way we will proceeed. Any goth'ca's in this process?
View 3 Replies View RelatedThere seems to be a lot of conflicting information on what can and can't stack together in the 3750X range.
I know that LAN Base can only stack with other LAN Base switches.
Can IP Base stack with IP services in 3750X? I have also heard that the 15.x.x IOS restricts mixed feature set stacks?
I know that Cisco recommends that all switches in a stack have the same IOS and feature set but having all IP Services in a stack can get too expensive.
We tested a QoS in a Cisco 3750E, IOS: 12.2(58)SE2.Voice traffice in the correct Q without any problem, but all the others traffic the Defualt Q (0), tried to capture the traffic and tcp/udp port are correct.Any thing wrong with my ACL or DSCP - CoS?? ( that ACL works fin on 4500 and 6500) [code]
View 3 Replies View RelatedI am not able to find the exact bug for Cisco 3750E stack - Debug Exception (Could be NULL pointer dereference) Exception (0x2000) error. Closest i can find is CSCsa72400 which only affects ver 12.2(20)SE4.All the stacks (3 switches) are running 12.2(50)SE3, It appears that the switch 1 crashed and reloaded. My hunch is its software but i cant find any related bugs. It could be hardware issue as well ?
View 4 Replies View RelatedI have a device which will be sending voice and data packets and is able to mark the packets with DSCP values. Voice, 18 and Data 42.If this was a straight through network, I'd be clear on how to handle this, but.....I will be putting this traffic into a VLAN to isolate it from some other traffic on the network. What is the best way to prioritize this traffic inside the VLAN? Will the Cisco switch look at and respect the DSCP values inside the VLAN and prioritize accordingly inside the VLAN? Or, do I need to do some sort of DSCP to 802.1p mapping? Another option I would be fine with would be mapping the DSCP values for voice and data to two different VLANs and then giving the voice VLAN priority over the data VLAN .... I'm using 3750E switches.
View 7 Replies View RelatedWhat is meaning backup on HSRP statas?There are 5 vlans.The other four vlans aren't backup status.Only one of five vlans display messeages. When I reload Catalyst3750E-1,debug log. [code]
View 6 Replies View Related9x3750E stacked switch (WS-C3750E-48PD-SF0) (15.0(1)SE2
C3750E-UNIVERSALK9-M)
2x10Gbe uplinks from EMC NAS
At a basic level, we have found that the 10Gbe uplinks have slow read performance with or without a port-channel configured (2-3 minutes for a 700MB file to desktop from the NAS) We switched back to testing a 1Gbe and the read speed is normal. Another anomaly is Win7 / 2008 machines read speed is fine from the NAS while the 10Gbe uplinks are in production?!
Write speed is great on 10Gbe. Only read speed is affected!! the switch is not reporting anything abnormal. We looked at SMB/SMB2 as another possible cause...
mls qos is enabled on the switch but not sure if this is affecting performance.
Is the ANY config that I need to carry out on the interfaces to get the read speed working as it should for both Win7 and WinXP. (MTU is 1500 throughout the enterprise, NAS included).
I have installed and configured 2 new WS-3750E-24TD in the last 30 days, that have software version 12.5(50)SE2-universalk9, on our flat Development LAN (currently 7 existing WS-3750E-24TD with 12.5(35)SE2-universal)The new switches have shutdown, 1 has shutdown twice and I just had the other one shutdown on the weekend, all the status lights on the left are lit up but no port lights are on, I am not able to console in to the switch all I can do is cycle power. I am planning on upgrading all switches to the latest software release universalk9-mz.150-1SE
could this problem be a version incompatibillity between the switches?
We have many 3750E's and need to use Finisar X2 modules FTLX8541E2. After 15.0(1) IOS upgrade the 3750's now recognize the Cisco part X2-10GB-LRM's, but will not recognize our Finisar modules.
View 1 Replies View RelatedSomeone had told me the 6500 switches can be stacked via fiber. This feature is available for the 3750s?
View 7 Replies View RelatedI have two WS-C3750-48PS-S switches and I need to add two more. The new part number I am looking at is WS-C3750X-48P-S will these all stack together ?
View 2 Replies View RelatedWe have three Cisco 3750 - 48port POE -LAN switches and i am trying to see if there are any issues when we stack POE and Non-POE type of switches.Aslo looking for information on the advanatage and disadvantage the stacking can provide on a Cisco 3750 48port.
View 3 Replies View RelatedWe currently have a stack of 3750G switches that are running 12.2(46)SE C3750-ADVIPSERVICESK9-M
Our 3750X is currently running 15.0(2)SE C3750E-UNIVERSALK9-M and I believe we were told you can't stack with a Universal IOS image. We have the universal on there because we have some 10GB fiber connections on it that Cisco told us wouldn't work otherwise.
I realize that the switch versions need to match, but the question is, which version should we work off to have use of the 10GB SFP card?