I am trying to stack the following -
3750G 12S - 12.2.53(SE2 IP Services) Running EIGRP & OSPF
with
3x 3750X 48P-S - 12.2.53(SE2 IP Base License)
Doing some research, the IP Base does EIGRP on the 3750X, does it do OSPF?
If not I will have to get licence for the 3750X?
We are experiencing output drops on our 3750G-12S (IOS 12.2.55).
I have monitored throughput with MRTG, but it doesn't seem that high compared to that the 3750G is supposed to handle 17.8 Mpps.
The 3750G's are stacked, running ospf, qos, multicast (IPTV) and etherchannel.Is the maximum throughput reduced by stacking or any of the other features?
I don't know if one can estimate what the maximum throughput is per ASIC or per port, but on one of the ASICs that is having drops the peak unicast load is 1.3 Mpps and multicast Mpps is 0.9 Mpps. Total ~2.2 Mpps.
This doesn't seem high at all and I don't understand why the drops are appearing. What I can do to find out the reason for these drops?
Has any come across show ver memory details on 3750G-48PS as below, One of our Catalyst 3750G running software 12.2(44)SE2 shows unexpected DRAM as below:
cisco WS-C3750G-48PS (PowerPC405) processor (revision F0) with 0K/12280K bytes of memory. This would equate to around 11MB memory which does not seem right... Is it a known IOS bug?
I have 2 3750 switch stacks which I would like to have redundant trunks between them. This will provide two physical connections traveling through different geographical locations for redundancy in the event that a cable is severed. I couldn't find anything in regards to setup/config. Does it matter if I go stack1/switch1 to stack2/switch1 and stack1/switch2 to stack2/switch2 or should they cross to opposite switches like a stack cable? I don't think that should be necessary, but couldn't find any documentation. Should there be an issue with loops?
View 4 Replies View RelatedOn first floor, I have two stack switches and each stack has got 4 switches. they all are working fine.Now the client would like to add one more stack on the 2nd floor. But the second floor switches are different when compared to the 1st floor switches.
can you have differnt IOS among different stacks. I knew in a stack we need all the switches should have same IOS version. But in between two stacks to communicate do we need same IOS or they can be on differnet IOS?
1st floor switches have 15.0 version and 2nd floor new switches has 12.2.58. Is this ok ?
1st floor switches are 3500 series ( Note: only one one Vlan 20 we are using on the both stack switches and we would like add same Vlan 20 on to the new stack)
2nd floor switches aew 2 catalyst 2960 switches.
Note: on the second floor switches one is 24 port switch and the other one is 48 port switch. so can i make them as a stack?
We have already done cabling from 1st floor to second floor. So no problem with that at all.
I have a 3750 as core switch, adding 2 stacks of 2960S to connect. I want to establish etherchannel between the 3750 and each additonal 2960S stack, do the channel group numbers between the 3750 and the new 2960s have to match? 3750 has two channel-groups(1 and 2) already configured. Need to know, I would create 2 additional channel groups (number 3,4) for each of the etherchannels between the 3 2960S Stacks and 3750? OR channel-group # is local to the device.
View 5 Replies View RelatedI would like to configure the policy base routing (PBR) on router (3900) base on the "specific tcp port" (TCP port 16255) to re-direct the traffic to another FE port.
From cisco web portal, CAT 4500 should support PBR as below:"Policies can be based on IP address, port numbers, or protocols. For a simple policy, use any one of these descriptors; for a complicated policy, use all of them." url...
Does 3900 router has the same features on the PBR? if yes, can it support "source tcp port" and/or "destination TCP port"?
We just purchased a bunch of 3750s, and we need to do EIGRP stub routing and VRF routing
For the newer IOS versions (15+), will I need activation keys?
using the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies View RelatedI have a 2921 router and want to use mpls feature. Right Now we are using c2900-universalk9-mz.SPA.151-4.M1 image but mpls static cross connect” is not working with this image. And will this image(c2900-universalk9-mz.SSA) be worked?
View 2 Replies View RelatedWhat features are supported in the image ipservces cisco 3750X-24T-S? Need NAT
View 1 Replies View Relatedsome of the features of 6500 are enabled by default and woudn't appear in the "Show run". See the command below and how do I make sure whether these featues are enabled by default or not. Would it appear in the config if enabled?
ip verify unicast source reachable-via rx
ip verify unicast source reachable-via any
storm-control broadcast level 70
what are the difference between the commands below and can they be enabled together.
spanning-tree guard root
vs
spanning-tree loopguard default
vs
spanning-tree guard loop
I think choose this SWITCH 4506-E and I need running only features L2 Metro, but Idont known what IOS for this!
View 1 Replies View RelatedI came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?
View 4 Replies View RelatedI got Two Distribution Switches of Cisco 3750G. Each Distribution have two 3750G switches stacked. I also have one Cisco 3750V2 Access Switch connected to both Distribution. When I am checking for redundancy, I can only get redundancy test pass for one link not atall for other. If I have a link up with Distribution 1 only then its fine; but disappointment with Distribution 2 link. I can see that the switch priorities of Dist 2 is not correct ie. Master's priority is 10 and Member's is 15.
My question is that due to misconfigured priorities on Distribution 2 stack switches I am failing with redundancy if ONLY Dist 2 is up and Dist 1 is down.
I've one Cisco 3750G-12S with ip routing enable, the swtich is with IP Service firmware, with PRR support.Currently set my default static route 0.0.0.0 0.0.0.0 10.1.18.71 to my Firewall A Currently all of the VLAN for will be routed to 10.1.18.71
I've created a new VLAN 2 for my 10.1.2.0/24 network with the VLAN interface 2 ip address 10.1.2.10, my intention is to route 10.1.2.0/24 traffic to my 10.1.2.1 by creating the access list and route-map.
I've configure my test pc with a static ip and my gateway pointing to 10.1.2.10 (VLAN 2 gateway) , i'm not able to route to 10.1.2.1.
I have a couple of 3750G-24T-E switches running IOS 12.2 I would like to upgrade to IOS 15.x. Is this possible? Where do I find some information on the required licenses and costs? I must admit that the cisco search function did come up with a few pages but i was not able to extract the required information. I have not used the new software activation features yet.
View 1 Replies View RelatedI've got a requirement to do Inter-VRF routing (need MP-BGP) using a private AS Number on a stack of 7 x 3750G's, my question ultimately is the performance overhead of doing such a change.
The stack will have no more than 300-400 routes even with the duplicates invoked from doing VRF leaking so I can't see much of an issue myself, we already have 2 VRF's and OSPF running in each VRF just don't have MP-BGP to do the VRF leaking.
Ultimately there will be about 4-5 VRF's (I know there's a Software limit of 26 VRF's on a 3750G).
I am having a switch 3750G (WS-C3750G-24TS-S) running a software version (c3750-ipservicesk9-mz.122-55.SE6.bin) and using the PBR with IP SLA.While, i am applying it on interface, it says not supported....
route-map TO-CAS-E0 permit 10
match ip address 125
set ip next-hop verify-availability 10.116.199.200 10 track 100 (if i change this command to set ip next-hop 10.116.199.200, it works)
!
WAN-L3-3750SW01(config-route-map)#interface GigabitEthernet1/0/11
[code].....
I have one switch 3750G12S I joined the company new, I found that they want to replace it with Alcatel stack switches. I didnt configure this Cisco switch before. how to configure it. I have 4 other new cisco switches in the topology which is not created yet. the 4 switches are all 2960.
View 17 Replies View Relatedhave 2 3750's one is an 3750E the other one is a G... Since they are 2 different versions Do I need to correct ios for each for example my 3750E switch i would have
IP BASE
c3750e-ipbasek9-mz.122-53.SE2.bin and for my 3750G switch should i use
IP BASE
c3750-ipbasek9-mz.122-53.SE2.bin
Which would be 2 separate images
I have a 3750G and bought a new 3750X. It possible to stack these two together?
View 5 Replies View RelatedI have a 3750g on which I am trying to configure the ip policy route-map command on each of the vlan interfaces. However after entering the command it does not appear. I'm not sure what to do at this point. I have changed the SDM template to routing and I am running the IPServices image.
View 2 Replies View RelatedI have just received a new Cisco 3750G Switch from my parent company. When attempting to install the switch, I discovered that it will not boot to CLI, only to the bootloader. After using the command boot, the switch attempts to boot the most current IOS version, but fails, stating "error loading XXXXXXXXXX.bin".
Obviously, I just need to get a functional version of the IOS onto the switch to boot, but the problem is exactly how can I do that? All (or most) the commands with which I am familiar are unavailable in the bootloader, so all methods known to me fail. Is there a simple way (maybe using the copy command?) to put the .tar or .bin file onto the flash?
I am trying to create an ACL that walls off a VLAN and only allows it to the internet. This is on a 3750G, currently the 3750G I am attempting this on is in a stack. I have another 3750G that is a standalone.
The first way I attempted this was to create two access-lists: access-list 101 permit tcp 10.249.1.0 0.0.0.255 any eq 80 access-list 102 permit tcp any 10.249.1.0 0.0.0.255 established
Let's call the 10.249.1.0 VLAN 2. I applied this to the VLAN2 interface, 101 out, 102 in. It didn't work. If I place a deny statement with nothing else, that works.
The second attempt was this: access-list 101 deny ip 10.249.1.0 0.0.0.255 any access-list 101 permit ip any any
I applied this to a VLAN I wanted to block VLAN2's traffic from reaching, let's call that one VLAN 3.
This lets all traffic from any VLAN (including the one I'm trying to block). If I remove the "permit ip any any", then all VLANs are denied. Which I understand is correct due to the implied deny all. What I don't understand is why it isn't applying the ACL to the specific VLAN.
I have a 3750G that used to be a Stack Master of a stack comprised of 2 identical switches. Since then, we have removed the stack from production, and I factory defaulted the stack MEMBER and that went fine. I just held the "Mode" button on the front until the lights all lit up and then issued the reload command and the switch came back with no configuration OTHER than the vlan database I issued the "del vlan.dat" command to no avail. I just manually removed all the vlans.
The stack MASTER on the other hand will NOT go back to factory defaults, and will also NOT erase the vlan database. Everything I try will NOT work. I've tried the following
1) Hold mode button & issue a reload after the lights start flashing
2) issue "Write Erase" then issue "reload"
3) issue "Write Erase", then issue "Write", then issue "reload"
4) issue "erase start" then issue "reload" (just in case the "write erase" command is being depriciated or something weird)
5) issue "erase start" then issue "copy run start" then issue "reload"
Is there a special way to reset a StackMaster back to factory defaults?
I have one 3750X with C3KX-NM-10GT, I need to interconnect using stackwise to 3750G-24TS. The 3750X needs IOS 15.0(1) to use C3KX-NM-10GT, and the latest IOS for 3750G-24TS is 12.2.55. How can I interconnect them using diferent IOS?
View 2 Replies View RelatedI have a 3750G switch that can't detect another switch or be detected through its stack ports. I tried the recommended test; looping a cable between the ports and rebooting. I get the following message as the switch boots: SM: Detected stack cables at PORT1 PORT2. However, if I connnect another switch, it won't detect it and can't form a stack.
View 4 Replies View RelatedI'm trying to upgrade the IOS ver on a 3750G stack (2 switches), but the img on the switch is too old.The stack is running IOS c3750-i9-mz.121-19.EA1d.bin, and when I tried to upgrade to a newer version, I tried to go to IOS ver c3750-advipservicesk9-mz.122-35.SE5.bin since I need to enable ssh on the switch, but the switch did not reload.
Here's a prtscreen of the switch ver:
Cisco Internetwork Operating System Software
IOS (tm) C3750 Software (C3750-I9-M), Version 12.1(19)EA1d, RELEASE SOFTWARE (fc1)
Copyright (c) 1986-2004 by cisco Systems, Inc.
Compiled Mon 05-Apr-04 22:40 by antonino
Image text-base: 0x00003000, data-base: 0x007CBC3C
[code]...
what IOS ver can I upgrade to that is not already deferred?
have one 3750G stack with 4 switches and this stack is presenting the follow log message:
%PLATFORM_UCAST-4-PREFIX: One or more, more specific prefixes could not be programmed into TCAM and are being covered by a less specific prefix, and the packets may be software forwarded.
In this stack we are using the layer 3 with OSPF routing, and the current sdm prefer is default:
switch-01-3750#sh sdm prefer
The current template is "desktop default" template.
The selected template optimizes the resources in
the switch to support this level of features for
8 routed interfaces and 1024 VLANs.(code)
I have two 3750G switches that are in a stack, and I am seeing these errors in the log:
002258: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlanid >=0 && vlanid < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 1279: pm_vlan_get_vlan_data) (CBAC01-3750-2)
-Traceback= 190F078 19729A0 1972A64 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002259: Feb 4 17:06:06.355 UTC: %BIT-4-OUTOFRANGE: bit 4096 is not in the expected range of 0 to 4095 (CBAC01-3750-2)
-Traceback= 10273BC 1027478 1972B50 1963764 110BC24 195F2F8 110BB9C 196D2C8 195ECD4 110BC24 19658B0 110BB9C 196D1D8 194C2B8 195D24C 110BC24 (CBAC01-3750-2)
002260: Feb 4 17:06:06.355 UTC: %PM-3-INTERNALERROR: Port Manager Internal Software Error (vlan > 0 && vlan < PM_MAX_VLANS: ../switch/pm/pm_vlan.c: 773: pm_vlan_set_portlist) (CBAC01-3750-2)
[code]....
Any one try to form a stack with mixed 3750-X and 3750G? Is there any prerequisites in hardware and software?
View 5 Replies View RelatedI am currently having performance issues running a 3 x stack 3750G (different models) as a core for a network of roughly 12 x distribution switches. [code] As above, I have a 12 port Fibre switch and 2 x 3750G-48 port switches. [code] I tried to change the SDM to route but hit another issue where the 3750g-48 does not support SDM route so I had to revert back to desktop VLAN.Could the SDM Template be the reason for slow performance? If so which SDM Template should i use as this is the Core L3 switch.
View 5 Replies View Related