I have a 2921 router and want to use mpls feature. Right Now we are using c2900-universalk9-mz.SPA.151-4.M1 image but mpls static cross connect” is not working with this image. And will this image(c2900-universalk9-mz.SSA) be worked?
View 2 RepliesI came across this Multichassis EtherChannel Features when read about information from Cisco Smart Business Architecture.After checking further, knowing that Cataly stwitch 6500 supports this feature.provide information that beside Catalyst 6500, is there any other model of Catalyst switch can support this feature?
View 4 Replies View RelatedDoes 2650 and 2620 support MPLS ? If yes what IOS version should i download?
View 10 Replies View RelatedI am designing a remote site that will have MPLS as primary and a site2site as backup, both connections on the same 2921 router. My problem is monitoring the connection status of the connections? Testing reachability to the MPLS router at the data center would allow bringing up the VPN, but once the VPN is up the data center router is reachable again. Is there a way to track reach ability through a specific interface?
View 1 Replies View Relatedi m planning to use the 2921 router for both mpls and internet connection , to 2 different isp also am planning to use bgp with a public providor independant
i m planning to buy sla for the mpls link
Will ACE 4710 support for IPS features?
View 1 Replies View RelatedI am trying to stack the following -
3750G 12S - 12.2.53(SE2 IP Services) Running EIGRP & OSPF
with
3x 3750X 48P-S - 12.2.53(SE2 IP Base License)
Doing some research, the IP Base does EIGRP on the 3750X, does it do OSPF?
If not I will have to get licence for the 3750X?
I would like to configure the policy base routing (PBR) on router (3900) base on the "specific tcp port" (TCP port 16255) to re-direct the traffic to another FE port.
From cisco web portal, CAT 4500 should support PBR as below:"Policies can be based on IP address, port numbers, or protocols. For a simple policy, use any one of these descriptors; for a complicated policy, use all of them." url...
Does 3900 router has the same features on the PBR? if yes, can it support "source tcp port" and/or "destination TCP port"?
We just purchased a bunch of 3750s, and we need to do EIGRP stub routing and VRF routing
For the newer IOS versions (15+), will I need activation keys?
using the 55xx as a L3 Distribution switch or even as a Core. By enabling the L3 features does it allow you enabled L3 SVI's for VLAN interfaces or are there interfaces on the daughter card that are used for routing instead?
View 5 Replies View RelatedWhat features are supported in the image ipservces cisco 3750X-24T-S? Need NAT
View 1 Replies View Relatedsome of the features of 6500 are enabled by default and woudn't appear in the "Show run". See the command below and how do I make sure whether these featues are enabled by default or not. Would it appear in the config if enabled?
ip verify unicast source reachable-via rx
ip verify unicast source reachable-via any
storm-control broadcast level 70
what are the difference between the commands below and can they be enabled together.
spanning-tree guard root
vs
spanning-tree loopguard default
vs
spanning-tree guard loop
I think choose this SWITCH 4506-E and I need running only features L2 Metro, but Idont known what IOS for this!
View 1 Replies View RelatedWe are experiencing output drops on our 3750G-12S (IOS 12.2.55).
I have monitored throughput with MRTG, but it doesn't seem that high compared to that the 3750G is supposed to handle 17.8 Mpps.
The 3750G's are stacked, running ospf, qos, multicast (IPTV) and etherchannel.Is the maximum throughput reduced by stacking or any of the other features?
I don't know if one can estimate what the maximum throughput is per ASIC or per port, but on one of the ASICs that is having drops the peak unicast load is 1.3 Mpps and multicast Mpps is 0.9 Mpps. Total ~2.2 Mpps.
This doesn't seem high at all and I don't understand why the drops are appearing. What I can do to find out the reason for these drops?
I have a couple of these routers in the lab with a very basic MPLS configuration on them. Everything works fine on the fixed interfaces but I cannot get the ldp neighborship to form between the 1FE2W interfaces on each router. Does this module support MPLS?
View 3 Replies View RelatedCan the new Cat 3850 run MPLS ?
View 4 Replies View RelatedWe are in the process of switching our infrastructure of our routing/firewalls/vpns over to cisco. We are switching our first location and one of the issues I'm struggling with is windows authentication pass-through for internally hosted web pages. Meaning, user inside our network has the 2921 as their default gateway, they try to access a web page that is hosted on the internal network but is secured with windows authentication. In the past, because they are logged into the domain internally, the website authenticates and loads. After switching to the Cisco, it asks for a password even though they are logged in.
Because its the web server that actually authenticates I'm not sure why the router isn't allowing that to happen, but I can't think of anything else that could be causing this behavior.
I have two Motorola MC9090's that will no longer connect through my MPLS back to coperate. They both stopped working at the exact same time yesterday.
They connect to a Cisco WAP321 that is connected to a Catylist 3750 that is connected to a Cisco 1921.
Each device can ping anything on that network. Both the switch and the router can ping the devices.
But if I try to ping a device on the coperate network the devices timeout.
The PC's connected to the switch via CAT5 have no issues connecting back to coperate (RDP to server)
I'm going to start the evaluation of implementing the virtualization of our campus LAN using MPLS.We'll get many inter-VLAN routing domains per VRF on the same LAN infrastructure.The LAN infrastructure is based on C6500 implementing VSS.Do you have experience with this kind of setup?Any known/faced issue that might prevent the setup of MPLS on VSS enabled C6500?
View 4 Replies View RelatedI was slightly dissapointed with the performance of the "pre-sales" phone number of Cisco in the Netherlands so I am asking it here instead.We decided on using 2 Cisco 2921 routers with 2.5GB ram to use for a MultiHomed connection using BGP. We already have our v4 and v6 space assigned as well as our AS number. The connections should turn up soon.What I could not find out with proper certainty on the Cisco Feature Navigator is if the IP BASE on the Cisco 2921 supports both IPv4 and IPv6 routing combined with BGP. This model uses the Universal IOS licensing which I found slightly confusing. I could not find a simple matrix with the supported commands either.
View 1 Replies View Relatedi have a router 2921 with the aproprieted voice card for E1 and licenses. I would like to know how to configure it for incoming and outgoing calls. I already configured the ephone and SIP phones for internal calls. now i just need to configure it for send and receive external calls.
Router:
IOS: c2900-universalk9-mz.SPA.153-1.T
CME: 9.1
ISP from Brazil:
type: E1
signal: R2 Digital
Channels: 32
Phone Number Iniital: XXXX-9250 (main)
ephones-dn numbers: 9250 to 9280
I have bought DRAM MEM-2900-2Gb for 2921, and received the following error...
Validation failed for DIMM0
*****System halted*****
%SPD info: DIMM0: Invalid DIMM type (only UDIMMs are supported)
We have remote office where we have 2921 router with 6 layer 2 switches. We have few servers which need to be in specific vlan.
2921 router does not have switching engine we are using this to support VOIP.
So on 2921 router i created 6 sub interfaces for each vlan and assign them to their specfic vlans. Then I have trunk connection to switch 1. Now switch 1 connects to all other switches in the network. As our company design all layer 2 switches should be transparent mode. i tested them i can ping from one switch to all other switches.
Router vtp mode i set to transparent mode and from all switches i can ping the router sub interfaces.
I've studied and labeled out MPLS and MPLS VPNs several times. The situation I'm presented with is a little different from most of the case studies I've seen in my MPLS books. I've attached a diagram.
We have a IPsec site to site tunnel from our main HQ router to a Cisco ASA 5510 in the core network in the colo. This allows our HQ office to reach the private sub nets in our core without using a Cisco VPN client. The problem we are running into is that this seems to be putting undue strain on the Cisco 2811. I feel like the 2811 should be able to handle it but doing any kind of upload or download through the tunnel spikes the CPU/Interrupts and makes the router CLI basically stop responding until the traffic transfer is stopped or completed. During this time, certain Cisco SCCP phones on our Broad works platform cycle while the SIP phones on the same platform are OK. We are trying to alleviate the load on the 2811 by setting up a VRF from the HQ network to the private VRF used in the Core for private sub net communication. The problem I'm having is the the HQ also has some public traffic that I do not want to include in the VRFs and would like to have it travel through the P2P circuit we have and access the internet or other public devices through the core public IP Internet routing table.
The flow would be this:
-going to a public address use the public internet routing table
-going to private address in the 10.x.x.x or 172.x.x.x - use VRF to core Private network.
This is a little different of a set up from most of the VRF VPN examples I've seen. Most of those the CE devices is completely private. This is not the case at our HQ.
We have the problem that MPLS labeled packets are not being processed on EHWIC-1GE-SFP-CU if L3PDU + Shim-Header exceeds 1500 bytes.When we move the config exactly to the on-board Interface Gi0/0 it works with put any problems. [code]
View 1 Replies View RelatedI need to confirm internet access from remote network through MPLS cloud to another site. Let me explain. We have a MPLS network with Wind stream as listed in the visio drawing; site 1 has internet access through the Time-Warner cloud for all users. Site2 has internet access through the Wind stream MPLS router. Site three has no internet access, and only has LAN access layer2 through Windstream routers to Site1 for networks 192.168.0.0/24, 10.1.1.x/24. My question is can we give everyone at Site 3 internet access through the MPLS network down into Site 1 using the Time-Warner ISP cloud.
I placed routes on the Site 3 3750 stack IP route 192.168.50.x 255.255.255.0 to the interface of the MPLS router at site3, then at site 1 we have IP route 192.168.50.x 255.255.255.0 to the MPLS interface, and able to ping all anything on the 192.168.50.0 network. I added the IP route 0.0.0.0 0.0.0.0 192.168.50.x the MPLS router interface, we do not have internet access at Site 3 using Site 1 network.
I confirmed at Site 1 from the Cisco 3750 switch we can ping 4.2.2.2 = Google. How to confirm this will work and what’s required to complete this connection to give everyone at site 3 internet access through Site 1 Time-Warner.
I have a CISCO2921. I am not able to bring up its gi0/1 interface. It stays down down.
[URL]
I know that interface is not coming up because of "no media" below. Router#sh int gi0/1 | i media Auto Duplex, Auto Speed, media type is no media
I have tried media rj-45 and media sfp which have also not worked. The other end of this link is ethernet handoff. What is it that I have to do for the link to come up? If I change the connection to gi0/2, I think that will work because I see this for gi0/2:
Router#sh int gi0/2 | i media Auto Duplex, Auto Speed, media type is RJ45
configuring up a 2921 router for remote site which is fitted with 24 port Etherswitch module.As part of this setup I have defined 3 vlans on the router, but when I go onto etherswitch and for example set switchport access to access vlan 3 it is not aware of this vlan.Do I have to set up trunk inbetween Router and its etherswitch?Wish I had ordered seperate switch as it would have been easier or am I missing something.sho vlan-switch shows my vlans but on swicth sho vlan brief does not.
View 10 Replies View RelatedAn interface on 2921 router is not coming up. When I shut/no shut the interface, I see this:
Router#sh log | i 0/2
Oct 17 08:55:06: %IP_VFR-7-FEATURE_DISABLE_IN: VFR(in) is manually disabled through CLI; VFR support for features that have internally enabled, will be made available only when VFR is enabled manually on interface GigabitEthernet0/2
Oct 17 09:00:35: %LINK-3-UPDOWN: Interface GigabitEthernet0/2, changed state to down
[Code]...
I thought I saw a post/question in regards to "how to" configure a Broadband backup for a MPLS circuit.. What I am trying to do is use a cable/dsl/ broadband (secondary) connection as a backup to a MPLS circuit (primary). I have EIGRP and BGP configured on both the branch endpoint and the tunnel headend. The tunnel is used by the interface that connects to the secondary circuit. The branch location router is a 1841 and the "headend" tunnel router is a 3825. I am wondering about the configuration/syntax of a "weight" or static route that can be used to have data flow over the tunnel when the MPLS circuit goes down - and then switch back to the MPLS circuit when it comes back on line.
View 1 Replies View RelatedThis is for a short temporary time until I get cisco 3560s in place. I have a 2921 configured and it is connecting to an HP non managed non VLAN switch and I cant get any traffic to pass from my computer to the router (pings or anything). Here is brief configuration that should be enough. [code]
Here are my vlans 1-default, 2-management, 192-data, 92-voice, i believe its running rapid spanning tree protocol. Do i have to take off encapsulation on my data vlan to get it to work or make the data vlan default vlan for everything. I am lost as to why this is not working.
I have a 2921, and I have 4 network segments. In segment 172.16.0.0./27 I wand to "pair" somehow connections. I mean IP 172.16.0.x has to have MAC aaaa.bbbb.cccc and so on, and not accept connections otherwise.How can I do that?
View 7 Replies View RelatedIs it possible to configure a Cisco2951 and a Cisco2921 in HSRP?
View 1 Replies View Related