Cisco Switching/Routing :: Replacing 7206VRX With 6509-E Sup2T?

Dec 9, 2012

We are planning to implement the 6509-E with two Sup 2Ts and a few 48 ports switches. We also want to make this the router for our network and replace the 7206VRX.

View 5 Replies


ADVERTISEMENT

Cisco Switching/Routing :: Command QoS In VS-Sup2T Of 6509

Dec 10, 2012

I have a 6509 witch a sup vs-Sup2T,  and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP..  look
 
This is a configuration in a sw 4507
 
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
  
In 6509 with sup2T and version 15.0.SY2  Im no sure.. I see two command
 
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3  
and 
table-map cos-discard-class-map 0 1 2 3 4 5 6 7  

View 1 Replies View Related

Cisco Switching/Routing :: 6509 - Upgrade Sup720 To Sup2T In VSS Cluster

Jun 21, 2012

I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
 
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).

View 9 Replies View Related

Cisco WAN :: 6509 - How To Upgrade IOS On SUP2T

Jan 15, 2013

Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
 
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
 
)#boot system flash ?
WORD  System image filename
<cr>
 
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
 
Here is the original show boot command:
 
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =

[Code].....

View 1 Replies View Related

Cisco :: 6509 / 3750 - Sup2T IOS 12.2SY And QoS

Aug 21, 2012

I am thinking the Sup2T is just too new and I have queuing setup, if it is preferred or if I need to rethink how I am going at it.

I was able to get a working config between the 6509 and some 3750s.   Saturated the links and trickled some VoIP and Video traffic across it  without a single "interesting traffic" drop.  I have attached the  topology of my lab and the configs of the switches I was able to get  working (after many many head scratching moments).  I still have to lab  up the other portions of my topology, but its a start.
 
Is there a command equivalent to "show mls  qos interface <interface> stat" for the Sup2T?  The closest I  could find was "show queuing interface <interface> details" but  it just doesn't give was the other command does.  I want to be able to  see CoS/DSCP ingress and egress the ports.

View 0 Replies View Related

Cisco Switching/Routing :: MLS On 6500 With Sup2T

Aug 9, 2012

Cisco 6500 with 2T supervisor engine with following software Cisco IOS Software, s2t54 Software (s2t54-IPSERVICESK9-M), Version 15.0(1)SY1, RELEASE SOFTWARE (fc4)
 
The problem is that, I am not able to configure Multilayer Switching (MLS) (mls rp ip) in the global config command. Although the "mls" is visible on the config menu. but when I say "mls ?", the router prompt "unrecognize command"
 
Not sure if SUP 2T support MLS or it come with different name.

View 1 Replies View Related

Cisco WAN :: Upgrade Sup720 6509 Chassis - Configure Sup2T Management Ports?

Jul 1, 2012

We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?

View 1 Replies View Related

Cisco Switching/Routing :: 6500 - Configuring VSS With Two Sup2T?

Aug 4, 2012

I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active

View 6 Replies View Related

Cisco Switching/Routing :: Upgrade 6500 Sup2T From 15.0 To 15.1

Jun 4, 2013

I am trying to upgrade Sup2T from 15.0 to 15.1 (same feature sets).  I have the new  image in bootflash and have changed the boot system statement to boot from the new image and the config register is 0x2102.  However, everytime it reboots it loads the old image. [code]

View 4 Replies View Related

Cisco Switching/Routing :: Catalyst 6500 VS-SUP2T-10G QoS Configuration

Apr 22, 2013

I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration  between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
 
Civic_6506VSS#sho mod
Mod Ports Card Type                              Model              Serial No.
--- ----- -------------------------------------- ------------------ -----------
1    4  CEF720 4 port 10-Gigabit Ethernet      WS-X6704-10GE   

[Code].....

View 1 Replies View Related

Cisco Switching/Routing :: 6506E SUP2T QOS Channel Consistency

May 21, 2012

I have a catalyst 6506E (WS-C6506-E) with a SUP2T supervisor (VS-S2T-10G) card and a 10G interface card (WS-X6816-10G-2T) + DFC4.I have configured an etherchannel to another switch with the 2 10Giga ports of the SUP2T card and 2 10giga ports of the interface card.I only use the 10Giga ports of the SUP2T card so the cards have the same QOS transmit capabilities.But they do not have the same receive capabilities.
 
So when I configure QOS (with the new commands on SUP2T) on my 4 ports within the Etherchannel, 2 ports move down because of the inconsistency.
Till this point, no surprise.
 
The problem is that the command "no platform qos channel consistency" replacing the "no mls qos channel-consistency" does not exist.I run the last IOS 12.2(50)SY1 IPSERVICESK9.
 
And I cannot have QOS on my Etherchannel on the 2 cards.Or I have to use 4 ports of my interface card but in case of failure of this card, I loose the whole etherchannel.I there a way to avoid the consistency check ?

View 2 Replies View Related

Cisco Switching/Routing :: 6500 - Upgrade From SUP720 To SUP2T With New Chassis?

Apr 28, 2013

We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
 
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
 
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
 
The requirement is we would like to replace these switches with minimum downtime.

View 6 Replies View Related

Cisco Switching/Routing :: 3750X - Connect C3KX-NM-10G To X2 10G Port On Sup2t In 6500E?

Mar 17, 2013

Is it possible to connect 3750X with C3KX-NM-10G to X2 10G port on sup2t in 6500E switch.There is Cisco OneX Converter Module, but I could not find that it is supported on sup2t.

View 2 Replies View Related

Cisco Firewall :: 6509 - Replacing Faulty FWSM Module In Cluster

Apr 15, 2013

We have a faulty FWSM module in Cisco 6509 switch in Active/Standby cluster mode
 
We have purchased a refurbished FWSM module to replace it. It has the same FWSM OS 4.0 (4) and is in factory default configuration
 
What procedures should I follow to make this unit live and sync the config between the current active unit to this one.

View 1 Replies View Related

Cisco Switching/Routing :: 3825 / Replacing Routing Function With 3750 Switch?

Jul 27, 2012

I have the task of replicating the router config on a 3825 router on a 3750 switch. Reason is we are taking out the router and replacing it with the switch to make use of the router for other functions.
 
Below is main part of the router config:
 
!
ip source-route
ip cef
!
!
multilink bundle-name authenticated
!
license udi pid CISCO3825 sn FCZxxxxxxx
!
vlan internal allocation policy ascending

[code].....
 
The 3750 switch I have runs C3750E-UNIVERSALK9-M, Version 12.2(55)SE3 on a LAN BASE license.
 
The first thing I have done is to order for a license upgrade to IP BASE which would give the support for OSPF routing.I do not see much of an issue with the Interface configs, however, I am not too sure about replicating the routing config on the switch.
 
My question is can I run the commands as shown for the OSPF routing on the switch? If not, can I get suggestions on how best to set this up on the switch?

View 4 Replies View Related

Cisco Switching/Routing :: Replacing Defective Redundant Sup-720

Oct 29, 2011

How to replace a defective redundant sup. I read on several articles that inserting new redundant sup should not be an issue as the active sup will always send its configuation to the standby. We are running SSO on the Sup720. Should I switch it to RPR before I install the redundant sup? I read a case wherein they switched it to RPR from SSO before inserting the new redundant sup. My concern is the IOS mismatch since Cisco doesn't always send the same IOS on RMAs.What I am planning is this.
 
1. Save/Backup configuration
2. Remove the redundant sup on slot 8 (since it is a 6513)
3. Insert the new redundant sup on slot 8.
4. Check if all the configurations were synced from slot 7 to slot 8.
5. Copy the IOS from sup-bootflash to slavesup-bootflash. (if the IOS are not the same)
6. Check show bootvar to see if the boot variables are correct.
7. If bootvar is the same, reload slot 8 to boot the new IOS.
 
Is this a good plan or am I missing something? I am worried with this document if the redundant sup has a different software. If i insert the card in slot8, according to Cisco, it will revert to RPR. If slot 8 boots and it has a different OS, then slot 7 will switch to RPR even if it's active. Would I still be able to access the slavesup-bootflash of slot 8? Is it going to boot 100%? I read that doing a force switchover will cause a flip and RPR would cause the line cards to reinitialize and I don't want that. Well I am not going to do a force switchover since i want slot7 to be active and retain slot 8 as hot.

View 3 Replies View Related

Cisco Switching/Routing :: Replacing A Backup Sup 720 On 6513

Nov 21, 2011

I am replacing a faulty sup720 on a 6513. It s the backup/hot not the active sup. It has the same IOS on it. Is it correct that all I need to do is remove the faulty and replace it with  the new sup and do a wr mem? Fromwat I have read their should be no down time all connectivity should remain stable?

View 6 Replies View Related

Cisco Switching/Routing :: Replacing SUP 6L-E With 7L-E On 4506 Switch

Dec 6, 2012

We have sup engine 6L(WS-X45-SUP6L-E) on two 4506 switch. both switches connected in LAN (HSRP primary and Secondary).
 
We are going to replace it with Sup7LE. What is the best procedure to get this done with minimal outage?Any other important thing to be noted ? Note : We have Lincence for SUP 7LE

View 2 Replies View Related

Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

     x3     48 ports
     x1     NAM
     x2     Sup720
     Running 12.2(18)SXF3
 
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis

Nov 21, 2011

I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:

x3     48 ports
x1     NAM
x2     Sup720

Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?

View 2 Replies View Related

Cisco Switching/Routing :: 3750G Replacing VTP Server Switch

Apr 8, 2013

I'm due to replace a stack of 2 x 3750 switches very soon with 2 x 3750Gs.  These 2 current switches are the VTP server for a small domain.  I have put the config on the new switches switches and I made it a server and used the same VTP domain and password etc and got the VLAN info ported over.Now I did this a while back and noticed the switches are in transparent mode with a revision number of 0, I need to set this back to server and swap the switches out but the revision will be lower than the client switches (around rev 200), what do I need to do?

View 7 Replies View Related

Cisco Switching/Routing :: Replacing 1841 12.4 Advsec With 1941 15.2M SEC/K9

Jul 2, 2012

I decided recently to switch out our border router (1841 12.4 advsecurity) with a shiny new 1941 (15.2 SEC/K9) as the CPU upgrade was needed.The core below acts as a VPN end point to various other remote offices we have, all of which have a similar network design at each end (and all entirely managed by me). All of these are still running 1841's with 12.4 advsecurity on them as well. These are all GRE tunnels with ipsec procection on them (not crypto maps). [code]
 
Everything else works fine (NAT, route-maps etc), it's just these IPSEC/isakmp tunnels that are not playing ballIt's definitely not an ARP issue (all arps were cleared) and ICMP appears to work fine (ie, I can ping the remote tunnel's public IP endpoint from the core using the loopback for that tunnel as the source). I am suspecting it's something strange with the stateful firewall config, but I did try and apply ipsec and isakmp-msft to the ip inspect list, with no success.

View 1 Replies View Related

Cisco Switching/Routing :: Replacing WS-3750-48p With WS-C3750X-48PF-S?

Mar 10, 2013

In my MDF I have a 4stack of the WS-3750-48P switches. Is it possible to replace one with a C3750X48PF-S with out causing any issues? Or would it be better to just have 3 stacked and trunk this one to the core 4506. Keeping in mind I bought this one to expand the port number for one of our remote offices.. I would hate to send them the gig switch when there isn't as much usage..Besides if I can get my CFO on this switch he might authorize me to replace the rest... He is reticent to believe it makes really all that much of a difference.

View 2 Replies View Related

Cisco Switching/Routing :: Replacing 2801 With 2911 Router

May 7, 2013

I have a 2801 router that I am replacing with a 2911. I know the ports on the 2911 are Gigabits and the 2801 are Fe. I read where the IOS would not support backup and restore on each other . I am attaching a show ver on both routers. I need to know if backup and restore would work and or what other changes would need to get done.

View 1 Replies View Related

Cisco Switching/Routing :: Replacing C4507R-E With Nexus 5548UP?

Jul 25, 2012

We currently have an environment with a 4507 as the core switch connected to four stacks of 3750e's in the wiring closets. A pair of Nexus 5548UP's also hangs off the 4507, but at the moment more or less dedicated to a certain purpose..The 5548UP's have the L3 daughter card installed.
 
My question is: Can a pair of Nexus 5548UP's do a C4507's job? Would we be able to decomission the 4507 and replace with the existing 5548UP's + FEXes?

View 1 Replies View Related

Cisco Switching/Routing :: Replacing A Line Card On 6500?

Mar 20, 2012

when replacing a line card on a 6500, i gather there is no config stored on the card, its all held on the sup, so when i put in another card the config will be the same?

View 2 Replies View Related

Cisco Switching/Routing :: Replacing Two 3750 (stacked) With 3750X

Jun 3, 2013

I was wondering what general steps might be taken in order to "replace two(2) 3750 (stacked) with one (1) 3750X - Server Access". General steps and what I might have to do configuration wise. I know i'm copy pasting the existing configs into the new switch, but are there any caveats?

View 5 Replies View Related

Cisco Switching/Routing :: Replacing 3750X Stack Member?

Feb 7, 2012

I have two 3750X in a stack. Each 3750X has one 10Gb uplink to primary core1 and one 1Gb uplink to backup core2 configured in 2 etherchannel groups. The member switch has bad ports, so I need to replace it. I have spare 3750X unit. Is it possible to connect the spare unit to the stack and then move the RJ-45 cables from the member with bad ports to the new member? That way I can minimize servers downtime to just a few seconds..If that would work, then the last step would be to move the 10Gb networking module from old member to the new one, as well as the secondary PSU. Is it doable? Also according to the documentation, all I need to add new member is matching IOS version, correct?

View 1 Replies View Related

Cisco Switching/Routing :: 3750x Replacing 2nd Stack Wise Cable?

Nov 20, 2011

I have two 3750G switches stacked together however it's not in a full ring configuration:

Stack Ring Speed        : 16G
Stack Ring Configuration: Half
Stack Ring Protocol     : StackWise
 
And as shown below it's obvious which cable is not working:
 
show switch neighbors
Switch #    Port 1       Port 2
--------    ------       ------
1         2            None
2        None           1
 
It's not flapping - it's like the cable isn't there at all. I'm going to try reseating the cable in there and perhaps an all out replacement if necessary. My question - is there any threat of a reboot of the switch stack or of partitioning of the switch stack by trying to get the 2nd cable working?

View 1 Replies View Related

Cisco Switching/Routing :: 3750 / Replacing Failed Member In Stackwise?

Dec 18, 2012

The stackwise marketing info states that when a failed member is replaced with a new switch the replacement switch "gets the exact configuration of the old device".  I would figure it takes a little more than just disconnecting and connecting a new switch in the same spot on the stack. doing this with 3750 family switches?  What are the steps to prepare the stack for a new member?  what steps need to be taken on the replacement switch before insertion into the stack to make sure it gets configured like the unit it was replacing?

View 5 Replies View Related

Cisco Switching/Routing :: Replacing A Dual Supervisor Module In A 6513 Switch?

Jun 18, 2012

I have a supervisor blade, (VS-S720-10G-3C), in a 6513 that is faulty and needs replaced. Do I need to replace the IOS on the new supervisor blade to make sure it is the same as the IOS image that is on the Active supervisor module, or will it synchronize automatically?
 
In the synchronization process, the active supervisor engine checks  the  standby supervisor engine run-time image to make sure that it  matches  its own run-time image. The active supervisor engine checks  three  conditions:
 
#
•If it needs to copy its boot image to the standby supervisor engine
#
•If the standby supervisor engine bootstring needs to be changed
#
•If the standby supervisor engine needs to be reset
 
 I was reading the above documentation that mentioned the active supervisor should copy the image if it detects a newly installed standby supervisor blade with a different image, is this correct or was it referring to synchronizing the configuration file?

View 3 Replies View Related

Cisco Switching/Routing :: 6509 / 4900 - Network Down Cause Switching Supervisor With Redundancy

Jan 11, 2012

we've had an issue with our network, we have 2 6509 connected with redundancy, which are connected with 2 x 4900 Switches, from which are connected to a ESX Chassis for visualization, the thing is that the ESX stopped working, and the 4900 switches, and the main core were suffering from overload, they hang on it very well, in order to stop the overload, one of the links to the ESX Chassis were disconnected from one of the 4900 switches. The CPU usage from the 4900 and the core(6509) went down below 40%, and then they started to migrate the virtual servers from the chassis to another 2 chassis that were added right after. They were actually working well, but suddenly the 6509 changed to the other supervisor after everything was OK. We were wondering what could have been the cause of this, maybe the virtual servers migrations, maybe the overload from the ESX ? We also had a few question, is there any need to reload the cores every few months as a planned task ? Because the cores have been up for more than 1 year. And also is there any kind of of tool to monitor the CPU status, or the status overall from the cores or the switches ?

View 3 Replies View Related

Cisco Switching/Routing :: 6509 - Upgrading Switching Infrastructure

Apr 11, 2012

The have around 80 staff and I think the current infrastructure is overkill for the size of the company. The current kit is old and they have no GB ethernet ports. They currently have:-

Core Switch:
1x Cisco c6509with a 48 port fast ethernet module (WS-X6248-RJ-45)
and an 8 port fibre module (WS-X6408A-GBIC)

I'm looking to replace this with something with 72 ethernet ports and 8 fibre ports

Access Switches:
2x 3500Replacement needs at least 48 ports and 2 fibre modules each

and 2x 5500Replacement needs at least 72 ports and 2 fibre modules each.

View 13 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved