Cisco :: 6509 / 3750 - Sup2T IOS 12.2SY And QoS
Aug 21, 2012
I am thinking the Sup2T is just too new and I have queuing setup, if it is preferred or if I need to rethink how I am going at it.
I was able to get a working config between the 6509 and some 3750s. Saturated the links and trickled some VoIP and Video traffic across it without a single "interesting traffic" drop. I have attached the topology of my lab and the configs of the switches I was able to get working (after many many head scratching moments). I still have to lab up the other portions of my topology, but its a start.
Is there a command equivalent to "show mls qos interface <interface> stat" for the Sup2T? The closest I could find was "show queuing interface <interface> details" but it just doesn't give was the other command does. I want to be able to see CoS/DSCP ingress and egress the ports.
View 0 Replies
ADVERTISEMENT
Jan 15, 2013
Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
)#boot system flash ?
WORD System image filename
<cr>
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
Here is the original show boot command:
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =
[Code].....
View 1 Replies
View Related
Dec 10, 2012
I have a 6509 witch a sup vs-Sup2T, and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP.. look
This is a configuration in a sw 4507
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
In 6509 with sup2T and version 15.0.SY2 Im no sure.. I see two command
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3
and
table-map cos-discard-class-map 0 1 2 3 4 5 6 7
View 1 Replies
View Related
Dec 9, 2012
We are planning to implement the 6509-E with two Sup 2Ts and a few 48 ports switches. We also want to make this the router for our network and replace the 7206VRX.
View 5 Replies
View Related
Jun 21, 2012
I support an active VSS cluster using 2 x 6509E chassis with single Supervisor 3C modules in each chassis. I want to replace these with Supervisor 2T modules. All my service modules and line cards are supported with the Sup2Ts (I will also be implementing 6908 modules). Is there a document on the Cisco site for this? I haven't found one though I can find plenty that describe how to do a software upgrade.
(Note, I have a 3rd (non VSS) 6509E chassis that is also part of this core network and that will maintain VTP/V LAN's etc).
View 9 Replies
View Related
Jul 1, 2012
We've just invested in a pair of Sup2Ts to upgrade a Sup720 6509 chassis but I'm unsure exactly how the management port(s), aka the Connectivity Management Processor (CMP), should be configured (and patched) in a dual supervisor system?Is each CMP an independent entity or is the management interface configuration (IP address, gateway, etc) replicated between supervisors?If it's the latter then do both management ports need to be physically connected at the same time?
View 1 Replies
View Related
Sep 6, 2011
I have just started to discover the power of EEM and am already monitoring config changes on our switches with EEM.I would like to be notified of any interface going up and possibly down. on our 6509's and 3750's This is just to be aware of anyone patching anything in.
View 1 Replies
View Related
Apr 11, 2013
We just replaced our ancient 6509 dedicated SAN switch with a Nexus 5548UP (with 4 2248 FEXs).Our old SAN 6509 was completely separated from the Core 6509, and that Core 6509 doubled as a Datacenter switch. We've now segmented the "Datacenter" and "Core." The SAN and servers are connected to the Nexus gear rather than the Core. The old SAN had only 3 vlans. One for SAN data (Vlan16), one for management interfaces (Vlan250), and one for switch management (Vlan15).
As part of my cleanup, I want to get rid of that Vlan15 and use vlan250 for switch management. In another building, we have a 3750 that provides SAN (Vlan16) and management (Vlan250) connectivity to a single Equallogic box and a Dell PowerVault tape drive for backup purpose. That 3750 is the only device that still has an address on Vlan15 (other than the core). Refer to the drawing below.
The Core 6509 is the gateway for Vlan250 and Vlan15. I have created an interface for Vlan250 on the 3750. ACLs exist on vty connections of each switch allowing telnet access ONLY from the Mgmt 2960. There are no ACLs on the Vlans themselves.From the Mgmt 2960, I can telnet to the 3750 using either its Vlan250 IP address or its Vlan15 IP address. However, if I shut down Interface Vlan15 on the Core 6509, I can no longer telnet to the 3750, not even using its Vlan250 IP address.
The connection times out. If I attempt to telnet to the 3750 via Vlan250 from the Core 6509, I get connection refused (which I should get due to the ACL on the vty connections). I can still telnet to other devices on Vlan250 (such as the management interfaces on the Nexus 5Ks). Why am I able to telnet to the 3750's Vlan250 Interface only when the Core's Vlan15 Interface is Up?
View 5 Replies
View Related
Jul 14, 2011
We are a new medical school located in PA. Just have just completed a new building and are now working on getting our network finished. Here is the situation we have a 50MB Internet Connection that comes into our network that then hits the ISPs Cisco 3750 which sends it to two of our Cisco 3750s for redundancy. From the 3750 goes into our Cisco 6509 with a FWSM module, then out from there to our distribution switches which are all Cisco 2960s.
What we would like to do is to control how much WAN connectivity each of our VRFs get. Right now we have a Faculty, Student, and Research VRF formed, and are trying to figure out the best spot where we can say Faculty gets 30MB of Bandwidth, Students gets 10, and Research gets 10. If possible would like burst capabilities.
View 3 Replies
View Related
Dec 20, 2010
We have a 6509 that was connected to 2 other locations(location A and B) and our local lan (location MAIN). We wanted to move the location A and B to a 3750 switch and only allow the traffic that needed to access our location MAIN to come through the firewall. The only problem I ran into is that before location A and B were on different interfaces so in the 6509 firewall the routes for traffic to our MAIN location was done by static routes.
I.E.
static (MAIN_intf,A_intf) 192.1.1.72 10.94.10.72 netmask 255.255.255.255 0 0
static (MAIN_intf,B_intf) 192.2.2.72 10.94.10.72 netmask 255.255.255.255 0 0
[Code]....
because it has a static overlap, which makes sense to me, but my question is how do I configure the network to get this to work? Do I have to reconfigure my network and access-list? Do I need to add more ports between the 6509 and 3750? I'm not sure if this is the best way to do what we want. If something is not clear I'll try my best to explain the setup, but I just took over for our I.T. guy when he left.
I put 10.10.10.72 instead I should have put 10.94.10.72. the routed port is on a different subnet than the computer I'm trying to access.
View 4 Replies
View Related
May 6, 2012
My core switch is a 6509-e and my IDF closets have 3750's.I have a couple of vlans currently setup, that can communicate with each other.VTP is setup Client/Server where as my core is Server, all IDF's are Client.
What i'm trying to do is create an isolated VLAN. I want to setup a DHCP scope and use helper address. When i plug in a client to that VLAN, i want it to get an IP, but not have any other network access.
Is this possible to do without switching to Transparent mode? If not - what reprocussions will i see by switching to transparent mode?
View 9 Replies
View Related
Aug 6, 2012
I am aware that the 3750 switches are not able to support Netflows, so I have created a SPAN port and spanning traffic from a specific port. I would like to create a seperate VLAN and trunk the traffic from the SPAN port down to the 6509 switch and then capture all the traffic for that VLAN on the 6509.
View 4 Replies
View Related
Mar 5, 2013
We have a 6509 series of core switches and 3750 series of L2 switches, There is no default gateway or any static routes to any IP.VLAN 1 is made admin down and another vlan is used for all communication here in this environment
Attached is configuration for reference But still I am able to take telnet or SSH. I want to know how telnet or SSH or tacacs authentication happens without any static or default route.
View 4 Replies
View Related
Feb 2, 2013
I am planning to upgrade the current core switch(3750) to 6509 series switch. Since we have a production network running we have to plan for an online core switch upgrade.
View 7 Replies
View Related
Jul 4, 2012
migration of an existing Sup720 configuration to a new Sup2T. At present we have a Sup2T chassis in the lab running 15.0(1)SY1 and a production Sup720 chassis running 12.2(33)SXI5.I've taken a copy of the production startup-config, renamed it to 'startup-config-BGFL_6509_MBAS-020712' and copied it to the bootdisk (and slave bootdisk) of the new Sup2Ts.I've then added the command 'boot config bootdisk:startup-config-BGFL_6509_MBAS-020712' in an attempt to boot from that config and have the Sup2T migrate it to the new config standards (particularly from a QoS perspective as mentioned here :[URL]
!
boot-start-marker
boot system flash bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin
boot config bootdisk:startup-config-BGFL_6509_MBAS-020712
...
Router#sh bootvar
BOOT variable = bootflash:s2t54-advipservicesk9-mz.SPA.150-1.SY1.bin,1;
[code]....
View 5 Replies
View Related
Aug 9, 2012
Cisco 6500 with 2T supervisor engine with following software Cisco IOS Software, s2t54 Software (s2t54-IPSERVICESK9-M), Version 15.0(1)SY1, RELEASE SOFTWARE (fc4)
The problem is that, I am not able to configure Multilayer Switching (MLS) (mls rp ip) in the global config command. Although the "mls" is visible on the config menu. but when I say "mls ?", the router prompt "unrecognize command"
Not sure if SUP 2T support MLS or it come with different name.
View 1 Replies
View Related
Sep 18, 2012
We have recently purchased new Sup2T to replace the Sup720. When we tried to copy the vlan.dat file across we are facing this issue. Sup2T is not booting up once delete the original vlan.dat file of the Sup2T & reload. Here is the console output during the process. What to do to get this Sup2T working.
[Code] ......
View 2 Replies
View Related
Aug 4, 2012
I'm configuring VSS with two Sup2T but the Sup2T of the standby not coming active
View 6 Replies
View Related
Jun 4, 2013
I am trying to upgrade Sup2T from 15.0 to 15.1 (same feature sets). I have the new image in bootflash and have changed the boot system statement to boot from the new image and the config register is 0x2102. However, everytime it reboots it loads the old image. [code]
View 4 Replies
View Related
Nov 14, 2011
If I have two stackable switches were only one stackable switch has two uplinks one uplink goes to one core 6509 switch and the other uplink goes to the other 6509 core switch can a Layer 3 etherchannel be used if each uplink go to a different core switch, by the way hsrp is running between both switches and also can you give an example how data will be routed from the stackable switch through the ethernetchannel to one of the core switch accross the WAN to another core switch?
View 1 Replies
View Related
Apr 22, 2013
I am migrating services from SUP720-3B to VS-SUP2T-10G= and moving to a VSS configuration between a pair of Cat6506 distribution layer switches. I need to enable QoS on these switches, primarily to trust dscp and also to prioritise voice traffic. The autoqos feature works for some ports but does not work on port-channel interfaces and port-channel member interfaces. How can I apply the qos settings for these interfaces in line with what auto qos would normally provide. My line cards are as follows:
Civic_6506VSS#sho mod
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 4 CEF720 4 port 10-Gigabit Ethernet WS-X6704-10GE
[Code].....
View 1 Replies
View Related
May 21, 2012
I have a catalyst 6506E (WS-C6506-E) with a SUP2T supervisor (VS-S2T-10G) card and a 10G interface card (WS-X6816-10G-2T) + DFC4.I have configured an etherchannel to another switch with the 2 10Giga ports of the SUP2T card and 2 10giga ports of the interface card.I only use the 10Giga ports of the SUP2T card so the cards have the same QOS transmit capabilities.But they do not have the same receive capabilities.
So when I configure QOS (with the new commands on SUP2T) on my 4 ports within the Etherchannel, 2 ports move down because of the inconsistency.
Till this point, no surprise.
The problem is that the command "no platform qos channel consistency" replacing the "no mls qos channel-consistency" does not exist.I run the last IOS 12.2(50)SY1 IPSERVICESK9.
And I cannot have QOS on my Etherchannel on the 2 cards.Or I have to use 4 ports of my interface card but in case of failure of this card, I loose the whole etherchannel.I there a way to avoid the consistency check ?
View 2 Replies
View Related
Apr 28, 2013
We recently purchased 2 Cisco 6500 series switches (with Sup 2T). These switches will be replacing our old 2 6500 series switches (with Sup 720).
We have 70 vlans and 90+ closet switches (2900) connecting the core switches We have 2 WLC connected to the core switch. We also have a 1 x 1 connection to a VSS switch which in turn connects to our Server Co-Location data center utilizing IPSec & GRE tunnel to connect to our Server Co-Location data center.
Our routing protocol is EIGRP. Our VTP domain at Server Co-Location is separate from our location “A” campus. I was wondering what is the best way to migrate our Core switches at location “A” campus.
The requirement is we would like to replace these switches with minimum downtime.
View 6 Replies
View Related
Mar 17, 2013
Is it possible to connect 3750X with C3KX-NM-10G to X2 10G port on sup2t in 6500E switch.There is Cisco OneX Converter Module, but I could not find that it is supported on sup2t.
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Jun 30, 2012
Do I need the Universal image to perform stftp on a 3750 or 3750-X?
View 8 Replies
View Related
Oct 10, 2011
I'm looking at adding a Cisco 3750-X switch running c3750e-universalk9-mz.122-55.SE1 (IP base license) into a stack of 3750-G switches running c3750-ipbasek9-mz.122-55.SE1.bin Given that the version and feature sets are the same I don't forsee any compatibility issues. Would there be any reason why a universal image wouldn't stack correctly with other switches running the single .bin file?
View 9 Replies
View Related
May 21, 2012
We have a stack of switches that is at the max number of members allowed in the stack. Problem is we are running out of port density and need to add more ports. So instead of adding a whole new stack I would rather replace 2 of the 24-port swicthes with 48-port switches.
If the two 24-port swicthes we are removing are stack members and neither of them are the stack master, I should be able to replace the 24-port switches with the 48-port switches without bringing the master offline? If the new 48-port switches are running the same IOS version as the current 24-port swicthes, they should add themselves to the stack?Would I have to tell the new 48-port swicthes what switch numbers they are replacing in order for them to be added to the stack since we are at the max number of members?Also since the 48-port swicthes are replacing 24-port switches will the master give the 48-port switches the configuration for only the 24-ports?
View 11 Replies
View Related
Jul 23, 2011
I have an old 6509. I have being using it as a switch. It is running CATOS.
Its configuration is :
WS-C6509 Software, Version NmpSW: 8.5(2)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 6 2005, 20:22:19
[Code]....
Any IOS version (bgp bundle) wich could be used to have 6509 as a router?
View 1 Replies
View Related
Apr 6, 2008
I got an invalid input message when I typed "ip routing". Is this the expected result? Does the 6509-E with Sup 720 and FWSM support "ip routing" command?
Version: 12.2(18)SXF5.
FWSM version: 3.1(4)
I have some routing problems between the switch and the fwsm.
switch(config)#ip routing
^
% Invalid input detected at '^' marker.
View 3 Replies
View Related
Dec 19, 2010
I have the following policy maps in on my 6509:
policy-map Customer
class QoS-voice
shape average 2000000
class class-default
fair-queue
When I apply it to an interface (int vlan1005)- I get:
Router (config-if)#service-policy output Customer
shape average command is not supported for this interface
Configuration failed!
This also happens with priority, bandwidth, etc. How can I configure QoS on this 6509 then?
View 4 Replies
View Related
Jun 29, 2011
I have searched the internet until my battery died. How to fix dribbles. If not, why have a counter for them. I have a 4506 one fiber hop away from a 6509 and I am getting dribbles
View 1 Replies
View Related
