Cisco :: 6509 - How To Fix Dribbles
Jun 29, 2011I have searched the internet until my battery died. How to fix dribbles. If not, why have a counter for them. I have a 4506 one fiber hop away from a 6509 and I am getting dribbles
View 1 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 6509 To 6509-E Chassis Upgrade?
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco Switching/Routing :: Upgrade Of 6509 To 6509-E Chassis
Nov 21, 2011I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
Cisco WAN :: Using 6509 As Router?
Jul 23, 2011I have an old 6509. I have being using it as a switch. It is running CATOS.
Its configuration is :
WS-C6509 Software, Version NmpSW: 8.5(2)
Copyright (c) 1995-2005 by Cisco Systems
NMP S/W compiled on Dec 6 2005, 20:22:19
[Code]....
Any IOS version (bgp bundle) wich could be used to have 6509 as a router?
Cisco :: No Ip Routing On 6509-E?
Apr 6, 2008I got an invalid input message when I typed "ip routing". Is this the expected result? Does the 6509-E with Sup 720 and FWSM support "ip routing" command?
Version: 12.2(18)SXF5.
FWSM version: 3.1(4)
I have some routing problems between the switch and the fwsm.
switch(config)#ip routing
^
% Invalid input detected at '^' marker.
Cisco WAN :: 6509 - Policy Map QoS
Dec 19, 2010I have the following policy maps in on my 6509:
policy-map Customer
class QoS-voice
shape average 2000000
class class-default
fair-queue
When I apply it to an interface (int vlan1005)- I get:
Router (config-if)#service-policy output Customer
shape average command is not supported for this interface
Configuration failed!
This also happens with priority, bandwidth, etc. How can I configure QoS on this 6509 then?
Cisco WAN :: Achievement With VSS 6509
Oct 25, 2010What i m achiving by VSS the same i use to achieve before with 2 redundant core switches, By flowing half vlan's from 1 switch and other half by another core and specifying HSRP priority according to spaning-tree vlan flow, either of them goes other core takesover
View 8 Replies View RelatedCisco :: High CPU On 6509 VSS
Sep 13, 2011I have high cpu problem on 6509 VSS(VS-S720-10G). When VSS was connected to LMS or NMS, the cpu utilization of VSS was very high(MAX 100%).
When they were not connected, the cpu utilization was normal.
I think it is because of SNMP gathering on LMS/NMS.
And I blocked arp table and forwarding table, but there was no change on cpu utilization. I couldn't find the bug reports and other references.
Info. IOS version : 12.2(33)SXI1
device : 6509 VSS(VS-S720-10G)
cpu utilization : snmp engine (30%~60%) peak, sometimes 100%.
Cisco :: 6509 - Maximum Distance For VSS And VSL
Feb 24, 2010how much distance can we have VSL,
I have 2 x 6509 serving as redundant switches and now i plan to upgrade to VSS, but both switch are 2KM away from each other.
Cisco :: 6509 / EEM Command To Read OID Value?
Feb 2, 2012I am trying to change SNMPv2 community string on 6509 remotely, without using expect script. I tried EEM applet (we cannot use TCL scripts), but it does not work. EEM command "action 10 info snmp oid 1.3.6.1.2.1.1.4 get-type exact" is supposed to store the result into an environment variable. It does not. Or at least not in the one that is documented. Is it a bug? We have IOS 12.2(17r)SX5. To get EEM version i ran "sh event manager version" and got "eem: (v240_throttle) 2.21.32". Does it mean i have EEM version 2.21?
View 6 Replies View RelatedCisco WAN :: Using 6509 As Core Router?
May 6, 2011One of the pur client want to use Cisco 6509 as core Router. STM Module they want to install in it and used as Core Routing through it. Is it ok with core network ?
View 2 Replies View RelatedCisco WAN :: 6509 - 2 ISPs From One Network
Nov 26, 2011I have a second link being installed this week to a second ISP. Each ISP has tunnels that terminate on there routers for various services. Right now on the 6509 I have a static default route which sends all traffic to ISP one. Once I get the second link installed I would only like to send specific traffic to ISP1 and everything else to ISP2 unless the link is down. Would policy routing on the 6509 fit my needs?I would like to send 172.20.0.0 / 24 and 10.25.0.0 to isp one and everything else to ISP2.
View 4 Replies View RelatedCisco WAN :: Configure SVI On 6509 Switch?
Apr 9, 2012How to config SVI on Cisco 6509 switches??
View 1 Replies View RelatedCisco LAN :: Limit Bandwidth In 6509?
Feb 25, 2012If two (one 6509A 9/26 with server A located in A end, 6509B with serverB located in B End) which is connected via a 1G link. If there is serverA send 700M file to server B via a 1G link. If I configured below command to 6509A 9/26, can I limit the bandwidth of server on bothincoming and outgoing to 500M?
class-map match-all FROM-SERVERmatch access-group name FROM-SERVER!policy-map FROM-SERVERclass FROM-SERVERpolice 500000000 conform-action transmit exceed-action drop!interface GigabitEthernet9/26service-policy in FROM-SERVER
Cisco Security :: Does SVI ACL Have Impact On CPU On 6509
Nov 15, 2011Does the SVI ACL have impact on the CPU on 6509 ?
View 7 Replies View RelatedCisco VPN :: Tunneling IPSec Through A 6509?
Mar 27, 2011Is it possible to tunnel IPSec through a 6509 with an FWSM installed without the packets being interferred with?My question arises because myself and a colleague were attempting to form an IPSec tunnel in just this environment last week and no amount of resetting policies, key phrases etc would allow the tunnel to come up. The 2821 was complaining about Phase 2 not matching but the policies were definitely matching and configured the same on both ends. If there shouldn't be an issue with the 6509 and the FWSM then I will post configs from both ends. The 6509 is configured to all all ports through for the two IP addresses for now and is performing a one-to-one NAT for the PIX that is behind it.
View 5 Replies View RelatedCisco WAN :: 6509 - 10 Gig EIGRP Metric
Oct 3, 2006I have recently connected a 10 Gig connection from the local telco between two sites on 6509's. These two sites also have a 1 Gig links between them. When I connected the 10 Gig link I expected the 10 gig link to be the preferred route, but after looking at the routes I noticed that both links have the same EIGRP path cost. Also the minimum BW for both links is 1000000Kb or 1Gb. Why?
View 11 Replies View RelatedCisco WAN :: Performance For 7600 / 6509 With SP-720
Dec 7, 2010I would like more information of performance to 7600 router with the SP-720, how many sessions full bgp routing it supports? I have 4 links 1 GB and a throughput of 900 MB.
View 4 Replies View RelatedCisco :: Setting Up Netflow On 6509?
Apr 5, 2012I am trying to setup Netflow to identify a problem I am having with a video conferencing system. Here are the commands that I have entered into the 6509 I am working on. I have checked this against another 6509 I have and these match. Not able to get netflow to show up on the solarwinds server. I have configured it to accept the netflow source coming from the 6509 I am working on.
ip flow-export version 9
ip flow-export destination 1.1.1.1 2055
ip flow-export sourc vlan 254
[Code].....
Cisco WAN :: REP Support On 6509 Series?
Sep 6, 2012Any plans to support REP on the 6500 series?We have Sup 720 with MSFC3.
View 1 Replies View RelatedCisco WAN :: 6509 IOS Upgrade With ISSU
Jun 7, 2011We are trying to test ios upgrade for Cisco 6509 switch with issu (in service software upgrade). We were able to upgrade the ios but there is one issue in issue 6509's supviseengine720 gigabit port lost the connection during the upgrade process.
View 1 Replies View RelatedCisco :: 6509 Syslog Not Working
Feb 6, 2013I have a 6509 on my network and also have LMS4.1 for management. My 6509 is listed in my lms as a device. The config is in LMS. But I am not getting any syslog messages in LMS for my 6509. I have logging turned on and I have my LMS server listed in the config using the logging IP address command. What could be missing that would prevent the syslog messages from showing up in LMS. I have other devices that send syslog messages fine.
View 2 Replies View RelatedCisco WAN :: How Many Sub-interfaces Can Exist On 6509
Jan 6, 2012Is there a limitation to the amount of sub-interfaces that can exist on a Cisco 6509? The switch has WS-SUP720-3B (Sup card), WS-X6724-SFP (linecard), and 12.2(33)SXH7 (IOS).
View 7 Replies View RelatedCisco WAN :: 6509 CPU 100% With Jumbo Frames
Jan 8, 2013I have two switches: Nexus 3064 (ver 5.0(3)U1(2)) and Cisco 6509.The 6509:
1 x WS-x6708-10GE 8 port Ten Gig module version 3.5, firmware 12.2(18r)S1.
2 x sup 720's, with PFC3A.
2 x WS-x6348-rj-45
4 x WS-x6748-ge-tx
The IOS is ipservicesk9-mz 12.2(33)SXH8b.Both switches have been running fine for quite a while(not connected to each other). I then ran a fiber connection between port Nexus:1/48 and 6509:Te9/1.When I ping (of any packet size) from the Nexus to the 6509 @172.19.4.254, the 6509's CPU goes to 100%. On occasion, we will get 1 out of 20 packets back in the reply.I reduced the MTU size on the three 6509 parameters until the CPU stopped going 100%.The magic number is 4175 bytes. 4176 and higher == 100% CPU.I am willing to put the fiber link to 1500, but how does one change that for just one port on the Nexus? I tried and it refuses to set the mtu. I also tried to setup a new service-policy but that didn't seem to work either.The Nexus users are all jumbo frame users. The users on the 6509 are all 1500 byte frame users, except for one user on a 1 gig port (ws-6748-ge-tx) line card. It is this user whom would like jumbos.
Cisco WAN :: 6509 With Sup 720 Configuration Upgrade
Jan 20, 2011I currently have this in our Sup720:
boot system flash bootflash:s72033-jk9o3sv-mz.122-17a.SX3.bin
boot bootldr sup-bootflash:s72033-psv-mz.122-17a.SX1.bin
I downloaded s72033-mp001-pz.122-33.SXH5
I read the documentation on Upgrading Software Images on Catalyst 6000/6500 Series SwitchesURL
I was wondering do I copy the s72033-mp001-pz.122-33.SXH5 to the sup-bootflash and bootflash? In the example it also uses disk0: but I get a <No device available>. Also keep in mind we're upgrading the application and maintanence partitions also. So this is a big upgrade and I've never done this before.
I guess the 2 things I want to know is:
1) Can I copy the s72033-mp001-pz.122-33.SXH5 to both the sup-bootflash and the bootflash? Can I run it just copying it to the sup-bootflash?
2) It was my understanding that I only needed one image file for the upgrade but the documentation says I need
"a. the main software image
b. the bootloader image"
Do I need another file? I'm a little confused. I did notice the files had different names and sizes and so do the ones on my current Sup 720.
And we are doing this tomorrow and I just happened to be reviewing the documentation one more time and somehow missed this.
Cisco WAN :: 6509 - How To Upgrade IOS On SUP2T
Jan 15, 2013Have a new 6509-E router with 2 sup2T blades. However it came with IPbase and we need to put Ipservices on it. I have copied ipservices IOS to bootdisk and slavebootdisk.
However I cannot get get to the boot command to point to bootdisk. It only allows me to point to flash:
)#boot system flash ?
WORD System image filename
<cr>
Yet I don't seem to have an option to copy this new IOS to flash. How do I get to copy it to flash:
Here is the original show boot command:
sh boot
BOOT variable = bootflash:s2t54-ipbasek9_npe-mz.SPA.150-1.SY1.bin,1;
CONFIG_FILE variable =
[Code].....
Cisco WAN :: 6509 Choosing IOS For Functionality
Nov 2, 2011choosing Ios for a funcionality.
We need to upgrade Ios in a 6509, the reason for we need to upgrade IOs is that we need implement the command xconnect in a interface. The current version of Ios not suport this comand.
How do we select the new IOS that suport this command?, ..we see a long list of IOS in the software download section of 6509, but not sure which one to choose..
Cisco WAN :: 6509 - VRF Limit In VSS With VS-S720-10G
May 8, 2011I'm planning to implement a VSS system with two 6509 and VS-S720-10G supervisor engines. In technical specifications is said that this card can support up to 1024 VRFs. Is this limit the same when working in VSS?
View 6 Replies View RelatedCisco :: 6509 Sup-2T Management Through CMP Interface
Dec 3, 2012 We acquired recentlty a new Cisco 6509 with Sup-2T supervisor card
My question is the following : we have a management subnet on a Copper-based switch; we manage all equipments through this network. I planned to configure the management interface on the 6509 to connect this switch & monitor the VSS through it However, since it is a CMP interface, most of the actions (SNMP, IOS upgrade.. won't be possible through this link) Moreover, I don't think LMS would be able to get the configuration through it (except by configuring a script running "attach" command & show run
Is there something I miss or must I add another interface of the Catalyst to this network (the problem being that I have no copper line card)
Cisco WAN :: DHCP On WAN Interface 6509
Mar 1, 2011I have a 6509 with SUP2 w/msfc2 at home, I am currently have dsl for internet with static IP addresses. Due to AT&T not wanting to support faster speeds in my area, I have to look at another option. All of these will be dynamic IP addresses, cable, uverse, etc.
I need to be able to enable dhcp on the wan interface so I can connect directly into one of the gig ports (either on SUP2 or 6316) or on a 10/100 port on a 6348.
I have the following image installed s222-adventerprisek9_wan-mz.122-18.SXF13.bin, according to Cisco's feature tool, it is supported.
I have tried "ip address dhcp" on the interfaces but they will only accept "ip address x.x.x.x", I looked at "ip dhcp" as well and only get the option for "relay".
I would hate to have to put something else in the mix to handle the dhcp portion. I may be keeping the adsl for my mail server traffic and backup in case of an outage on the new provider. So I need to be able to track if a link is up.
Cisco WAN :: Can't Enable MPLS On 6509-E
Apr 17, 2012I've got a 6509-E in the lab at the moment for some pre-deployment testing, however I don't seem to be able to enable MPLS on a select interface.
router#conf t
router(config)# interface gi1/48
router(config-if)#mpls ip
router(config)#
As you can see after I enter the "MPLS IP" command it simply backs out of interface level configuration back to global exec, and naturally the MPLS command doesn't show in configuration for that interface.
I'm running a SUP720-3BXL with WS-X6748-GE-TX line cards with the DFC upgrade (WS-F6700-3BXL).
The IOS is: s72033-adventerprisek9_wan-mz.122-33.SXI2a.bin
Cisco WAN :: 6509 Says Not Supported Due To Hardware
Feb 6, 2011I have a 6509 and a 6506- same IOS version and flavor, same hardware, etc. One supports rate limiting on the VLAN interfaces, the 6509 says "not supported due to hardware". What is the difference here? Im very confused on this since I was under the impression the chassis were the same- just in size.
View 1 Replies View RelatedCisco :: Unable To Get 6509 IOS Via Add To Repository Job
May 16, 2012This is a new install of LMS 4.2 evaluation. I have a current install of LMS 3.2 which is working. When I run an Add job for our core 6509 in Software Repository using cisco.com on the 3.2 LMS it works normally. When I attempt the same job in LMS 4.2 for the same device the device is not selectable in the left hand window and it has a message that says (This operation requires Containment data in Inventory. Either this is unavailable) Or (Add Image from CCO not supported). Also and probably related is that LMS 4.2 cannot complete an inventory update on the 6509s that we have and does not say why the inventory job collection failed. So far as I can tell the other devices inventory and offer IOS updates correctly. I ran a job to get all device package updates before I ran any of the jobs. The devices all pass credential checks except for HTTP, which is not activated on the devices.
View 4 Replies View Related
