Cisco :: 6509 / EEM Command To Read OID Value?
Feb 2, 2012
I am trying to change SNMPv2 community string on 6509 remotely, without using expect script. I tried EEM applet (we cannot use TCL scripts), but it does not work. EEM command "action 10 info snmp oid 1.3.6.1.2.1.1.4 get-type exact" is supposed to store the result into an environment variable. It does not. Or at least not in the one that is documented. Is it a bug? We have IOS 12.2(17r)SX5. To get EEM version i ran "sh event manager version" and got "eem: (v240_throttle) 2.21.32". Does it mean i have EEM version 2.21?
View 6 Replies
ADVERTISEMENT
Jan 13, 2009
What is the command for creating a user on an ASA 5500 running 7.2(3) that can only view the config but not make any changes?
View 8 Replies
View Related
Dec 10, 2012
I have a 6509 witch a sup vs-Sup2T, and I´m very confuse for to configure QoS. is diferent in the old supervisor..What is the command similar to map cos to DSCP.. look
This is a configuration in a sw 4507
qos map dscp 56 to tx-queue 1
qos map cos 1 to dscp 10
qos map cos 2 to dscp 18
qos map cos 3 to dscp 26
qos map cos 4 to dscp 34
qos map cos 5 to dscp 46
qos
In 6509 with sup2T and version 15.0.SY2 Im no sure.. I see two command
platform qos map cos-mutation testmap 4 5 6 7 0 1 2 3
and
table-map cos-discard-class-map 0 1 2 3 4 5 6 7
View 1 Replies
View Related
Dec 15, 2012
in my LAN the all access layer switchs/stacks are connected directly to core backbone switch (cisco 6509) via sfp fiber-optic, i want to protect my spanning tree setup with the "root guard" command.
1. where would i set this ? on uplink ports on access layer switches ? or on core backbone ports to which the access layer swithes connect to?.
2. can this be set on active (production) ports without downtime?
View 5 Replies
View Related
Oct 23, 2011
What is PIM? give me an example when I will use and not use the PIM command.
View 4 Replies
View Related
Nov 15, 2012
I have 1x Cisco 6509 with Sup2 and MSFC2 and it is running on IOS (c6k222-jk9sv-mz.122-17d.SXB11). I have following policy map :
Policy Map VOIP
Class IP PHONE
priority percent 75
and the following command on each interface: service-policy output VOIP those configuration are working fine on SUP2 with MSFC2 but last week I tried to upgrade the SUP2 to SUP32 on the switch and upgrade the IOS to the latest version (s3223-adventerprisek9-mz.122-33.SXJ4) but when I try to put service-policy output VOIP on each physical interface I am getting the following error:
"Priority command is not supported in output direction for this interface" and when I try to add service-policy output VOIP on a V LAN interface I am getting following error:
MQC features are not supported in output direction for this interface. Will I need to change something after upgrading to SUP32..
View 3 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
Nov 21, 2011
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
View 2 Replies
View Related
May 10, 2011
i have a 1841 Router that hang up @ boot.
Output:
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcb80
program load complete, entry point: 0x8000f000, size: 0xcdc3e0
[Code].....
View 1 Replies
View Related
Jun 13, 2012
I am using ACS 5.3 with the internal Database for user authentication, I would like to attribute to some users read only rights on the systems. by not configuring an enable password for these users?
View 2 Replies
View Related
May 18, 2011
I can create a read-only account on the ACS 5 server? I have the ACSAdmin account.
View 1 Replies
View Related
Mar 19, 2013
I'm switching from using a wireless usb adapter to a wired connection via ethernet cable.
When I plug the ethernet cable in however nothing happens, I've tried using it with a different computer and it works like a charm but this one doesn't seem to be working right.
HP Pro Small Form Factor 3010 Windows 7 32bit (Other computer was using windows vista)
Windows IP Configuration
Host Name . . . . . . . . . . . . : HPPro3010
Primary Dns Suffix . . . . . . . :
[Code]....
View 1 Replies
View Related
Mar 27, 2012
i have issue with whenever i m trying to download any file it's get upto almost 95-98%,but after suddenly stop.this issue with firefox, chrome browser
View 1 Replies
View Related
Jul 15, 2012
am looking for free software to read pdf, etc.
View 4 Replies
View Related
Sep 30, 2010
We are using ACS ver 4.2 and trying to setup users with limited access to our switchs and routers. Here is what we did:
1) Created a user in ACS
2) Create Shell command Autorization Set - ReadOnly
Unmatched Commands - Deny
Commands Added
show
exit
* this should limit the user to the show and exit command only (correct)?
3) Created a group - HelpDesk with the following TACACS+ Settings
Shell (exec) is checked
Priviledge level is check with 15 as the assigned level
Assign a Shell Command Authorization Set for any network device - selected
ReadOnly - shell command autorization set seleted
When the user logs on to the router/switch it appears that he has full access. He can enter the enable command, config terminal command, etc. All we want him to be able to do is to issue the show command.
View 13 Replies
View Related
Mar 11, 2011
I am trying to configure a 1941, but the router boots into readonly rommon . after configuring the router and copy running config to startup config, on reboot, none of the changes are saved, and boots back into readonly rommon
View 2 Replies
View Related
Apr 9, 2011
cannot read and receive emails
View 1 Replies
View Related
Dec 14, 2011
At each time I open the internet page,at the left in the bottom of the page near of the STARt buton, it's written:"Error on page".And like that I can't read my emails on YAHOO and I can't post any picture in FACEBOOK.
View 10 Replies
View Related
Feb 7, 2013
I am currently facing a major problem. I am a user of the Smart FTP software and have several files in it.However, the "Sites" folder is showing a blank screen. It shows nothing, when there are supposed to be at least 30 files.
I think I have discovered the cause of this; the "Read" permissions are off. Here is where my problem comes in, when I enable it and select "Apply Changes Recursively", it goes back to the unchecked "Read" permission. It doesn't seem to take into account the fact that I want to enable it.
View 1 Replies
View Related
Oct 7, 2012
I am currently using Time Warner Cable as my internet provider and I have been experiencing very slow internet connection speeds for the past few weeks. This has happened across multiple laptops and desktops both wireless and wired connections. I have done a ping and tracert test but am unable to read the results.
View 7 Replies
View Related
May 22, 2012
I have a motherboard intel DG41RQ and it has a built in lan card but i wanted to put another lan card via the PCI express slot and i put it and the flash lights on the network card are flashing but still the hardware manager and everything on the computer haven't even noticed that i put a new hardware.
View 36 Replies
View Related
Sep 18, 2011
tried to read the NEXUS 5000 cpu load: cseSysCPUUtilization 1.3.6.1.4.1.9.9.305.1.1.1 but there is a timeout: Timeout: No Response from 10.100.224.16 Other MIB values readout, like the system value, is ok.We use snmpv3.
View 4 Replies
View Related
Aug 27, 2011
When adding a new 256M card to ant slot on BXL SUP, it shows up in log as inserted, but am unable to format it and of course access it. I tried formatting to FAT16 on my MacBook, card gets formatted but remains unaccessible.
View 2 Replies
View Related
Nov 25, 2012
I am getting the following problem each time i restart the router
%Mainboard-2-initfail: read failure - device @ 0xA8
It does trows a lot of this errors and then restarts again making a clycle of the problem i have no clue what is going on.
View 1 Replies
View Related
Aug 25, 2011
Is there a way to create an account for the ASA using ASDM that is only read only and cannot make firewall changes?
View 1 Replies
View Related
Jul 8, 2011
Any tcp client software other than telnet and can read data in other formats than ASCII ? the problem i am facing with telnet is that it only reads ASCII format.
View 6 Replies
View Related
Jul 13, 2011
I have a network hard drive (NAS) in my LAN. I would like that a few computers in the LAN were able to only read but not write and the other computers could both write and read. Is there any way I could do this?
View 2 Replies
View Related
Jul 31, 2012
I was using the household Ethernet cord this morning and it was working normally. Then I stopped using the Internet to do a program tidy up. - there were a few program's that had been extras to other program's I don't need. Then I went to use the Internet again and it wouldn't connect through the Ethernet cord. I was able to establish that my computer is still able to access the Internet through wireless (which we don't often use on account of it been spotty). Could I have done/deleted/turned off something that allows my computer to read Ethernet cords?
View 2 Replies
View Related
Jul 9, 2011
I connected my Western Digital Studio II 2TB external harddrive which is formatted NTFS. I can access the drive and read it. But I can't write it. It says I do not have rights. I tried to get to be the owner of the device but it gave some kind of error.
View 2 Replies
View Related
Apr 13, 2011
I have a wireless router namely D-LINK 524. i know its a prtty old router..but its never let me down ever before..but thn today i decided to play a couple of games online using the psp/ps3 and well both the devices couldnt read the access point..
Then i go onto my pc and the internet on the pc dont work either :'( so then i reboot the modem nd wifi router..but to no avail.So i unplug da routerand connect da modem directly to the pc and it worked..so i was quite stunned..nd i miss playing online..
So to trim it down the problem basically is my phone/ps3/psp cannot find my access point AND my pc doesnt work when connected through the wireless router.
View 4 Replies
View Related
Mar 20, 2011
I have a customer that has a FWSM on a 6500, I want to create a read only account for them, i believe user privelage of lvl_3 When I log into the firewall it prompts me for a password straight away.
Is there a way that i can create a login that when it prompts me for a password, I can have a password setup to put into that prompt to get a certain level of access, instead of the standard lvl_15 access
View 9 Replies
View Related
Jun 16, 2012
How can I recover deleted read inbox messages?
View 1 Replies
View Related
Jan 25, 2011
we are on a p2p network with 4) windows xp, and 2) windows 7x64. I have a problem with one pc opening files in a shared folder. Only one pc will open the files in the folder as read only and the others will open with full control. I have checked if someone has the files open and no one did. I have checked the share attributes and they are set to full control to all users. The files are in word and xl and did not try anything other type of files. Is there a setting that makes the files read only for one user? This system is the owner and boss (win xp) and need a fix fast.
View 8 Replies
View Related
