I have a 6509 on my network and also have LMS4.1 for management. My 6509 is listed in my lms as a device. The config is in LMS. But I am not getting any syslog messages in LMS for my 6509. I have logging turned on and I have my LMS server listed in the config using the logging IP address command. What could be missing that would prevent the syslog messages from showing up in LMS. I have other devices that send syslog messages fine.
View 2 RepliesI have a VPN tunnel between two 892s. When either ISAKMP or IPSec SA lifetime expires tunnel stops processing traffic. However nothing is logged in the syslog. But when I enable debug crypto isakmp error and debug crypto ipsec error following entries appear:
ISAKMP:(0):Can't decrement IKE Call Admission Control stat outgoing_active since it's already 0
ISAKMP:(2041):R-U-THERE-ACK sequence number 0x63D809BB does not correspond to expected value 0x63D809BC
%CRYPTO-4-RECVD_PKT_INV_SPI: decaps: rec'd IPSEC packet has invalid spi for destaddr=XX.XX.XX.XX, prot=50, spi=0x3560099E(895486366), srcaddr=YY.YY.YY.YY, input interface=GigabitEthernet0
ISAKMP:(2043): IPSec policy invalidated proposal with error 4
Is this a bug? IOS is Cisco IOS Software, C890 Software (C890-UNIVERSALK9-M), Version 15.1(2)T2, RELEASE SOFTWARE (fc1)
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedRecently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedI have successfully completed HSRP and failover configuration.When both switch are runnign then the failover run successful and wheneber one link fail then the failover run successfully but when down one 6509(total box) the failover not working.....
View 7 Replies View Related6509 - Not working
1 6 Firewall Module
2 8 Intrusion Detection System
3 1 Application Control Engine Module
[Code].....
The Policy applied to the interface is just completely ignoring the configuration.
I am sure it is related to the 6500 architecture in some way. Same config is fine on the switch with the higher version on the sup card.
We have a 6509 running 5.4(2). We have set up a hyperterm session and connect to multiple devices, then we get to the 6509 and it will not work. When we reload the 6509 and we are consoled into it, we get data until it is finished reloading. Then the console connections is no longer there.
View 5 Replies View RelatedThe power supply on 6509 NEB A is not working with me . I have installed only one power supply on the box WS-CAC-3000W
It is showing me that "Input OK , Output fail " from the LCD
I tried with another WS-CAC-3000W , another power source but still same problem .
I have configured cisco 6509 to do nating and its not working. Static nat is perfectly working fine below is the config.
View 6 Replies View RelatedI have the following connectivity :Nexus(7004) - M1 8Port card with x2-10GB-SR <----------------------> 6509 -- 6704 card -- xenpak-10GB-SR ,The fiber link is not coming up.
View 4 Replies View Relatedinterface Vlan24
description Internal Wireless Internet
ip address 10.x.0.1 255.255.254.0
[Code]....
So, I am trying to limit the bandwidth used by this vlan. The service-policy output statement works, the service-policy input statement does not. My test is to get on that vlan and go to speedtest.net. My download speeds are about 3.5Mb/s, my upload speeds are about 20Mb/s.
it has something to do with this:
sh mls qos ip
QoS Summary [IPv4]: (* - shared aggregates, Mod - switch module Sid - Switch Id)
Int Sid Mod Dir Class-map DSCP Agg Trust Fl AgForward-By AgPoliced-By
[Code].....
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3
I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis?Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
I currently have a couple of 6509 chassis (router/switches) with the following hardware blades:
x3 48 ports
x1 NAM
x2 Sup720
Running 12.2(18)SXF3.I am keeping the four Sup720 modules and have purchased new versions of the others blades including two new 6509-E chassis. Can I take my stand-by Sup720 out of the production machine and insert it into the new chassis?
when we try to configure syslog to run over tcp it seems Cisco routers (12.4) do not send proper messages as syslog server does not record anything!Tested with syslog-ng (Linux) and Kiwi (windows) and both syslog servers have the same problem.These are some indications of the possible syslog tcp problems:
[URL]
Apparently Cisco ASA (8.2) seem to process this well!
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedI am only able to get InfoAlarm messages sent to via email notifications.My switch is sending logs to Cisco Works.Example:
13. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 UNBUNDLE Interface GigabitEthernet1/4 left the port-channel Port-channel2 *
14. 10.10.0.1 10.10.0.1 Apr 04 2008 10:34:41 EC 5 BUNDLE Interface GigabitEthernet1/4 joined port-channel Port-channel2
But I only recieve infoalarm messages:
ALERT ID = 00000UE
TIME = Fri 04-Apr-2008 11:04:00 PST
STATUS = Active
SEVERITY = Informational
MANAGED OBJECT = 10.10.0.1
MANAGED OBJECT TYPE = Switches and Hubs
EVENT DESCRIPTION = 10.10.0.1: Cisco Configuration Management Trap:InformAlarm; 10.10.0.1: Authentication Failure:MinorAlarm;
My switch is setup as:
logging source-interface Loopback0
logging 10.10.100.111
snmp-server enable traps bridge newroot topologychange
snmp-server enable traps syslog
I do not recieve critical or warning syslog messages.
I have a WCS working on version 7.0.172.0.Is there a way to send the alarms produced by WCS to another Syslog Server?
View 4 Replies View RelatedI have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies View RelatedI received a syslog message on my cisco 3845 router, what is that message mean. 11 13:36:06.265 UTC: ASSERTION FAILED: file "../les/if_ng_dslsar_tx.c", line 385
View 2 Replies View RelatedI am trying to setup syslog server on LMS 4.0.Everything seems to be working fine but I have a lot of stragne logs in my syslog.log file.Every single day I receive logs like :
Mar 05 09:31:03 127.0.0.1 100: <30> dmgt[1136]: 3007(I):Started application(1015) "e:CSCOpxincwjava.exe -cw:jre lib/jre -cp e:CSCOpxMDC omcatsharedlibMICE.jar;e:CSCOpxMDC omcatsharedlibNATIVE.jar;e:CSCOpxMDC omcatsharedlibjdom.jar;e:CSCOpxMDC omcatsharedlibxalan.jar;e:CSCOpxMDC omcatsharedlibxerces.jar;e:CSCOpxMDC omcatcommonlibservlet.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5.jar;e:CSCOpxMDC omcatsharedlibcastor-0.9.5-xml.jar;e:CSCOpxlibclasspath;e:CSCOpxwwwclasspath;wwwclasspathvbjorb.jar;MDC omcatwebappsupmWEB-INFclasses;libjrelibendorsedjacorb.jar;MDC omcatwebappsupmWEB-INFlibctm.jar;MDC omcatwebappsupmWEB-INFliblog4j.jar;MDC omcatwebappsupmWEB-INFlibjep-3.2.0.jar;MDC omcatwebappsupmWEB-
[code]....
I dont want to get any logs from 127.0.0.1. Is it possible to filter out logs from server ?
It appears that there are two different types of log information generated by the WLC-5508. The stuff that can be sent directly to syslog seems to be very basic while most of the good log information is sent via snmp trap. Does this setup to log to a SIEM in a manner that gives a good security view into the wireless controller?
View 4 Replies View RelatedLMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies View RelatedI am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 Replies View RelatedMy Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies View RelatedI want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
I get the following error:
SyslogCollector - [Thread: SyslogObjectForwarder] ERROR, 27 Mar 2012 09:02:12,254, Could not send syslogs, removing the subscriber...Connection refused: connect
SyslogCollector - [Thread: SyslogObjectForwarder] ERROR, 27 Mar 2012 09:03:15,223, Could not send syslogs, removing the subscriber...Connection refused: connect
Syslog subscription seems ok but syslog messages are dropped and not forwarded:
I attached SyslogCollector.log, SyslogAnalyzer.log, AnalyzerDebug.log
I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
I'm getting the Syslog messages frequently on daily basis.
View 4 Replies View RelatedIs there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedI am trying to log every connection (Build, deny, etc).But for some reason I don't see them sh log.
[Code]...
my LMS 4.2, syslog collector on LMS doesnt working even service syslog collector running normaly and also i saw in syslog_info is working to collect syslog from all router but not show up in dashboard monitoring.I have setting on every router to logging (ip address LMS) but on LMS no any syslog from router can collect.i did a selftest from LMS there are all PASS except nslookup fail, it is has relation with syslog not show up on dashboard?
View 5 Replies View Relatedi want to configure asa 5510 to send syslog messages to syslog server which i placed in my inside interface. also if enableing syslog will inrease the cpu utilization or memory? the necessary configuration parts?
View 1 Replies View Related