i want to configure asa 5510 to send syslog messages to syslog server which i placed in my inside interface. also if enableing syslog will inrease the cpu utilization or memory? the necessary configuration parts?
View 1 RepliesI've a problem with syslog logging on my Cisco ASA 5510 version 8.2(1). I need to:
- 1) log some ACL with warning level to log deny access.
- 2) log some ACL with informational level to log permit and deny access (notification level log only deny access and not permit access).
- 3) not log others ACL.
For 1), I configured the syslog server with warnings level and i enabled the logging rules with default level (syslog default level)
logging enable logging trap warnings logging host "interface" "host" . access-list "interface" extended permit ip any any log default.
For 2), I enabled the logging rules with specific level (informational).
access-list "interface" extended permit ip any any log 6 interval 300.
For 3), I disabled the logging rules.
access-list "interface" extended permit ip any any log disable
My problem is that the syslog logging level bypass the ACL logging level. Even if some ACL are configured with informational level, the ASA send only warnings logs to the syslog. I tried to configure the syslog default level to warnings, to remove the ACL and then put it back again with the specific logging level but I still have the problem.
I have an asa5510 on 8.2.2. I have my logging configuration as below [code] I am not getting any syslog output to the syslog server. I'm using kiwi syslog server latest version. Have tried disabling/reenabling logging and changing inside host destinations. Is there another command needed
View 4 Replies View RelatedI have recently setup Splunk to receive my syslog messages from my ASA 5510. In the past I used kiwi without observing this issue, but I needed more features than kiwi had available. Anyway, anytime I stop the splunk service my asa does not allow any outbound connections to be established.
View 2 Replies View RelatedRecently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedI have a Cisco ASA 5510 connected to 2 private lans (1 for my HQ pc's{inside} and 1 for the worldwide mpls{outside}) It is also connected to the public internet at interface "public" and my dmz at "dmz" interface. I suspect I have a routing issue because packet-trace yields allow, the nat looks ok and the objects look ok at least to me but I'm the one with the non working config so...Basically this is the desired flow:
1. I need all traffic from the inside to be able to flow to the outside unimpeded as they are both trusted networks. (this is ok right now as I allow everything via access-list 101.)
2. I need any host on the public internet to be able to reach a server on the dmz via the pat which I set up from the "public" interface to the "DMZ" interface. The desired flow would be that the person on the internet types in [URL] and this is directed to the public interface ip which forwards to the webserver object on the dmz. (I cannot get this working any which way)
3. I need the dmz to be able to communicate with another server on the mpls via the "outside" interface when it recieves the request from the public it then checks with this other server on the outside via nat(translating the dmz range into the ip of the outside interface on the firewall)I have a default route that points to the mpls or outside interface for 0.0.0.0 0.0.0.0 via 10.x.x.1 - (and although I'm not sure I suspect this could be conflicting with traffic that needs to be sent to the "public" interface .... meaning that the firewall should dump packets bound for 0.0.0.0 0.0.0.0 to the public interface - 184.x.x.194 but I'm very reluctant to change the default route as this is in production and I'm not sure how it will affect traffic).However, I do suspect that if I changed the route from default to static as such:
route 10.0.0.0 255.0.0.0 10.x.x.1 (this would get all lan and mpls traffic to the mpls gateway) route 0.0.0.0 0.0.0.0 184.x.x.193 (this would send everything else from public to the public internet gateway)I think this is accurate but then I would bypassing my corporate internet proxy which is behind the mpls gateway at 10.x.x.1? Is there a way to get http traffic originating from the lan (10.x.x.x) to use the mpls gateway and http traffic for the dmz to use the public internet gateway at 184.x.x.193. I don't want to start causing a flow problem for the internet nor do I want to bypass my corp internet proxy.Either way I cannot get this to work, eventhough the logic checks out, I cannot get even a ping response when I allow icmp any any for testing. Note: I can ping resources on each network from the firewall, not only it's own ports in the associated network but other resources on those networks as well.
Here is the running-config:
ciscoasa# sho run
: Saved
:
ASA Version 8.4(1)
!
hostname ciscoasa
domain-name marcjacobs.lvmh
[code].....
I am attempting to set up FTP behind this new CISCO ASA 5510 we just bought. I haven't configured a cisco device in 5 years, so I am having issues., i think i am close. If I FTP from outside (fixed) IP it connects and takes the password but hangs on PASV and gives no data connection below is my configuration. It is simple since I seem to have the connection inside correct. and yes you can connect to the FTP server from inside without issue.
Code...
I have one Asa 5510 with base license. now we wish to add one back up ISP for VPN fail over, is this possible to configure backup ISP with this ASA 5510 and how ?
Check ASA features
Cisco Adaptive Security Appliance Software Version 8.2(2)
Device Manager Version 6.2(1)
Compiled on Mon 11-Jan-10 14:19 by builders
System image file is "disk0:/asa822-k8.bin"
Config file at boot was "startup-config"
Cisco asa up 3 hours 35 min
Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
We have some users who use citrix outside corporate network through citrix web interface.These users are high priority users and we want to prioritize the citrix traffic. I want to make sure that my configuration will fullfill our requirements. Below is the configuration i was thinking to implement.:
ASA(config)# priority-queue outside
ASA(config-priority-queue)# exit
ASA(config)#access-list CTX-QoS extended permit tcp any 10.1.1.200
255.255.255.255 eq https
ASA(config)# class-map CTX-QoS-CMAP
ASA(config-cmap)# match dscp ef
ASA(config-cmap)# match access-list CTX-QoS
ASA(config-cmap)# exit
ASA(config)# policy-map CTX-QoS-PolicyMap
ASA(config-pmap)# class CTX-QoS-CMAP
ASA(config-pmap-c)# priority
ASA(config-pmap-c)# exit
ASA(config)# service-policy CTX-QoS-PolicyMap interface outside
I have created the following config for an ASA 5510. I implemented a DMZ on it. Is this config as secure as I can get it. I want the web server in the DMZ to only be able to access port 80 and 1433 on the SQL box inside.
ASA Version 8.2(1)
!
hostname fw
domain-name xxxxx
enable password k4HlcGX2lC1ypFOm encrypted
passwd 2KFQnbNIdI.2KYOU encrypted
names
[code]....
BTW, the ASA is running version 7.0 (8) and I'm doing this through the command line.I've got a group of workers coming in a couple times per week that need wireless access to 1 printer on our network and internet access; I'll deny them access to the rest of our LAN.I've already configured an AP with WPA2 on a seperate subnet and put a router between it and our network. I've setup the router to apply an ACL to allow access to the printer's IP, deny to the rest of our main subnet, and permit everything else to go to our ASA 5510 that is serving as our gateway. From a laptop connected to the access point:I'm able to ping the printer's ipI'm not able to ping other workstations or our servers, as intendedI'm able to ping the ASA's inside interface The only part I can't seem to pull off is the final part of getting the ASA to translate the IP's from the new subnet to the outside interface.
So we have:
Laptop > Wireless AP > Router with ACL > Primary LAN > ASA5510 > internet
PAT is working fine for the primary LAN, but the laptop can't hit the internet.
creating a DMZ with my current configuration. Most of my configuration has been through the ASDM as I am still learning. I'm looking for a good tutorial through the ASDM to get me on my way. What I need to accomplish is this:
I have an internal GIS server which needs to have a constant database connection to an remote GIS Server which is already configured. I've got a separate VLAN setup on my 3750 switch which connects to the DMZ configured port on my ASA with a security level of 50. My GIS server has been placed in the DMZ VLAN which is accessible from my internal clients. I have a /30 Internet block which is being used for Internet and VPN. I have a separate /28 block that I'm assuming I'll need for the DMZ to work properly.
Will give configuration of NAT for my internal users with 192.168.1.0/24 with single public IP.
I new to configure IOS version 8.3.
I'm working on getting a ASA 5510 set up and am having major difficulties. I'm really new to ASA and coming over from Microsoft ISA. Below is my configuration, how to get this all sorted out. As of nwo it doesn't appear that any traffic is going through whether it's incoming or outgoing. [code]
View 3 Replies View RelatedI want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
when we are configuring ASA 5510 8.2(5) for Authenticating with ACS 5.X Server is not authentication fail error.
View 2 Replies View RelatedI have existing Sonic FW in my company we are moving from sonic FW to ASA 5510 Security plus lice. I have two ISP currently connected to sonic Firewall I am planning to implement Dual ISP configuration on ASA5510.
View 12 Replies View Related I have Cisco 877-K9 router which sits behind an ASA 5510 FW. The Design :
Cisco 877-K9 DSL router (DSL with Static IP) ( DMVPN HUB )
||
ASA 5510 Firewall (Outside INT with Static IP / Inside INT LAN) (PAT & ACL)
||
Switch
||
LAN
Now my problem is, My Dmvpn configuration works just fine, I'm able to ping from my Cisco 877 to any Spoke & vise versa. I'm also able to Ping from my LAN to any Spoke Tunnel IP, but Im not able to ping any LAN IP at Spoke site nor am I able to ping my LAN from any Spoke site. I've googled alot but have come at designs where the ASA's are behind the Cisco Routers and not infront.
What protocol the firewall configuration replicate and monitor the interfaces?
View 1 Replies View RelatedI have new ASA 5520 units currently we are using ASA 5510... I have to migrate all the configuration to the new ASA 5520 units....I am wondering is there a possible way to export and import certificates from ASA 5510 to 5520....
how to export or copy all the configurations, plug-ins, certificates from 5510 to 5520.Existing configuration snapshot...CA certificates from third party installed for authentication and identity certificate from Verisign
WebVPN
Anyconnect
Plug-ins
IPSEC tunnels
NAT
I have configured redundant interface on ASA 5510
interface Redundant1
description *** INSIDES NETWORK ***
member-interface Ethernet0/1 (This is a 1000Mbps Port)
member-interface Ethernet0/2 (This one is 100Mbps)
no nameif
no security-level
no ip address
[code]....
Then... i issue following command and its OK!
ASA5510# show interface redundant 1 detail
Interface Redundant1 "", is up, line protocol is up
Hardware is i82546GB rev03, BW 1000 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
Input flow control is unsupported, output flow control is off
[code]...
It's transfer correctly then i no shut and back to normal Primary core switch Gi0/30 Interface again, BUT redundant interface no revert back. I issued this command again BW remain 100Mbps.
ASA5510# show interface redundant 1 detail
Interface Redundant1 "", is up, line protocol is up
Hardware is i82546GB rev03, BW 100 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
[ code]....
I did manually shut down and no shut the secondary core switch interface Gi0/30 Its changed correctly to 1000Mbps .
I want to configure ASA 5510 with complete redundancy first time. I have already studied all material from cisco web site. but there are avalible alot of material. and i'm confused about the exact my requirment material.
This is current configuration:
active# sh running-config
: Saved
:
ASA Version 8.2(5)
[Code].....
I currently have a LAN-based failover setup between two 5510s. The failover link is a crossover cable. In the current setup, if I unplug the crossover cable both units become active. From what I understood from Cisco documentation, each unit should mark the failover interface as down and there shouldn't be any failover. That's exactly how I want this setup to work.
View 5 Replies View Relatedconfigure the Firewall ASA 5510 in context based configuration in HA Mode with two different subnet....
IP Details are below.....:
interface Ethernet0/0
nameif outside
security-level 0
[Code].....
I have seen a few of these 305005 threads and they're usually related to NAT and resolved quickly. I have poked around a little, but can't seem to get it right. I'm using the Real-Time Log Viewer in my ASA 5510 and see lots of these 305005 errors between VPN clients and a server. Packet Tracer says it's being stopped at the PAT_POOL dynamic traslation to pool 1. I'm not solidly sure of what to change. [code]
View 9 Replies View RelatedWe have 2 ASA 5510's setup in an active, standby failover configuration. When the primary fails over to standby, the 3rd party cert does not failover to the standby ASA. The users then receive the CERT missing, invalid message and have to select yes, no to move on. This does not occur when the primary is not in failover mode. It is my understanding that failover fails over certs but in our case it does not apper to be working correctly.
View 1 Replies View RelatedI had a working active/passive pair of ASA5510's, and then I had to do a rush firmware upgrade, but didn't have time to do it on the secondary at the same time. Now I have made config changes and upgraded the secondary firmware to be the same, and wish to know if I plug it back in if it will think the secondary has the "correct" config or if it will know that the primary is newer. I disconnected the failover cable because it was complaining about version mismatches constantly.
Is it safe to add the secondary back in or is it possible it will be declared newer and overwrite the config?
I have turned on the aaa command authorization without applying adequate privileges to the user. I can now log in through that user but the ASA 5510 displays an error :ASA 5510# show running-config
ERROR: % Invalid input detected at '^' marker.
ERROR: Command authorization failed.
I am unable to make any configuration changes on the firewall. Is there any default user through which I can log in and disable the aaa authorization ? if not, how can I resolve this situation ?
I can't seem to send config changes to our syslog server on a 2950, I'm fine with 2960's and 3750's. The Cisco 2955 is using the latest IOS c2955-i6k2l2q4-mz.121-22.EA14.bin.
Here is what I have added:
logging buffered 64000 debugging
logging console informational
logging monitor informational
[Code].....
The only sylog message I get is "Configured from console by username on vty0 (10.1.1.35)
we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedI have cisco 5550 Firewall, one messages appear in syslog server from Firewall, (warning) i want to stop this message from appearing syslog traps.
View 2 Replies View RelatedI am try to configure ASA 5510 with 8.3 IOS version.My internal users are 192.168.2.0/24 and i configured dynamic PAT and are all internet .
i want configure identity NAT for remote access VPN.Remote users IP pool is 10.10.10.0 to 10.10.10.10
i know to configure NAT exemption in IOS 7.2 version. But here IOS 8.3 version. configure NAT exemption for 192.168.2.0/24 to my remote pool( 10.10.10.0 to 10.10.10.10).