Cisco Firewall :: ASA 5510 Redundant Interface Configuration
Aug 14, 2012
I have configured redundant interface on ASA 5510
interface Redundant1
description *** INSIDES NETWORK ***
member-interface Ethernet0/1 (This is a 1000Mbps Port)
member-interface Ethernet0/2 (This one is 100Mbps)
no nameif
no security-level
no ip address
[code]....
Then... i issue following command and its OK!
ASA5510# show interface redundant 1 detail
Interface Redundant1 "", is up, line protocol is up
Hardware is i82546GB rev03, BW 1000 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(1000 Mbps)
Input flow control is unsupported, output flow control is off
[code]...
It's transfer correctly then i no shut and back to normal Primary core switch Gi0/30 Interface again, BUT redundant interface no revert back. I issued this command again BW remain 100Mbps.
ASA5510# show interface redundant 1 detail
Interface Redundant1 "", is up, line protocol is up
Hardware is i82546GB rev03, BW 100 Mbps, DLY 10 usec
Auto-Duplex(Full-duplex), Auto-Speed(100 Mbps)
[ code]....
I did manually shut down and no shut the secondary core switch interface Gi0/30 Its changed correctly to 1000Mbps .
View 1 Replies
ADVERTISEMENT
Feb 14, 2012
I am configuring a pix 525,i just found out how to activate the subinterface on it so that's good,the box has a primary unit and secondary unit, both are connected from G0 to redundant switches,if i do a show failover, it says it's using the serial based lan failover, which is fine by me,however, do i need to create a single, regular interface.. or a redundant interface?,i.e. if i create a regular subinterface, will failover still apply to this interface?,or for failover to work, do i need to create a redundant interface (with a redundant id)? i do not seem to have the option to create a subinterface when adding a redundant interface.
View 7 Replies
View Related
May 8, 2011
I have two ASA 5540s, ver 8.4 configured in Active/Standby failover.I am also using the redundant interface feature for my Inside interface. Gig0/0 is the active primary and Gig0/1 is standby.
I will activate failover monitoring of the Inside interface using the monitor inside command.
My question concerns the failover monitoring of the redundant interface. If the gig0/0 connection were to fail would the Gig0/1 interface become Active, AND simultaneously result in a full device failover?
Or, does Gig0/1 of the Inside interface redundant pair simply become active and not change the Inside interface device failover state? Thus NOT resulting in a device failover.
View 1 Replies
View Related
Jun 10, 2013
we have two ASA 5510 connected in failover, and a pair of cisco 2960s switch connected in stack. Currently one interface of primary ASA is terminated on switch1 and a interface from standby is connected to switch2 as Inside, and switch1 and switch2 are in stack. for redundancy purpose i want to use multiple interfaces of ASA for inside , so first i thought to use etherchannel , but it has a limitation that , it cannot be terminated on stack switch(as per cisco document [URL]
So my question is :
1. can we use redundant interface feature where 2 physical interfaces combined to a redundant interface (eg interface redundant 1) for inside redundancy purpose.
2. Can these ports from primary/standby ASA terminated on stack switches (2960s), will this work (if the switch with active port goes down, will the other port take over in the redundant interface with the other switch).
View 1 Replies
View Related
Jul 29, 2012
I am unable to see 4th interface on my firewall i.e fastether0/3 on my firewall ASA 5510.
Below is the output.
ciscoasa# sh int ip br Interface IP-Address OK? Method Status Protocol Ethernet0/0 x.x.x.x YES CONFIG up up Ethernet0/1 x.x.x.x YES CONFIG up up Ethernet0/2 unassigned YES unset administratively down down Internal-Control0/0 127.0.1.1 YES unset up up Internal-Data0/0 unassigned YES unset up up Management0/0 192.168.1.1 YES CONFIG up up
View 8 Replies
View Related
Feb 24, 2012
Does OSPF work between a VSS L3 MEC & an ASA Redundant Interface? Both 6509 are in VSS and a L3 MEC is formed to the ASA.Both ASA ports are a part of a L3 Redundant Interface. Please note there is only a single ASA in this topology. [code] Now, the OSPF neighboring does occur and go into the FULL state on this device, however soon enough, the state enters INIT/DROTHER state.But as soon as I disconnect the physical connection 6509(Standby) The OSPF adjacency goes into FULL mode.
View 5 Replies
View Related
Mar 20, 2011
Have an ASA 5510. Setting up a new DMZ zone for wireless and it will only have Internet access. What are the steps so that users on this new DMZ subnet can VPN into the Outside interface on the same ASA?
View 4 Replies
View Related
Mar 1, 2011
I have a trouble with Cisco ASA 5510. I configured an SSL VPN with bookmarks to some application. When the users make access to the Web Portal they have to login twice: one for enter in the SSL and one for enter in the application.
How to bypass double authentication?
View 1 Replies
View Related
Mar 26, 2013
I attached the complete config. The earlier discussion, I cannot select reply. Looks like ACL is denying it. But I am not sure which one or how to permit it.
sh run
: Saved
:
ASA Version 8.0(4)
[Code].....
View 7 Replies
View Related
Sep 14, 2011
I would like to route traffic that are coming in and going out to the same interface on ASA. I am using inside interface with security-level 100. In this URL, [URL], ASA is able to do that.
View 5 Replies
View Related
Oct 5, 2012
I need the ssh access on my ASA outside interface and have added
ssh ipremoved 255.255.255.255 outside access-list acl_outside extended permit tcp host ipremoved any eq 22 but this is the log i get from ASA
Oct 06 2012 16:10:04: %ASA-3-710003: TCP access denied by ACL from ipremoved/39884 to outside:ipremoved/22
Cisco Adaptive Security Appliance Software Version 8.2(5) Device Manager Version 6.4(5)
View 7 Replies
View Related
Mar 26, 2013
I have a WAN interface and 2 LAN interface. I need both the LAN be able to access a server outside the network via the WAN (outside) interface. I am using a ASA 5510 firewall instead of a router, because I don't have a router. It looks simple enough but it does not work. I ping from the a PC (172.16.22.8) connected to LAN (inside) Network to 10.10.10.1 which is the WAN local interface also did not work. But from the ASA Firewall, I could ping my LAN (inside) PC. I followed a config i get from this forum. However, it did not work. Below my config.
interface Ethernet0/0
nameif outside
security-level 0
[Code]....
View 5 Replies
View Related
Feb 4, 2013
I'm not clear about the capabilities of the ASA 5510 GigE interfaces (eth0/0 and eth0/1) with an without IPSEC tunnels enabled.
This page [URL] shows a figure of 170Mbps 'Maximum 3DES/AES VPN Throughput'. Does that mean per IPSEC tunnel or for the whole interface if it is IPSEC-enabled?
View 3 Replies
View Related
Feb 13, 2012
I am having issues with the ASA 5510 management interface. I can't communicate with this interface. It is showing DOWN/DWON even if I type NO SHUT several times.
My existing config is as follows
our-asa-01# sh run
Saved
ASA Version 7.2(5)
hostname our-asa-01
names
dns-guard
interface Ethernet0/0
[code]....
View 5 Replies
View Related
Jun 20, 2011
On our ASA 5510 we already have one ISP link terminated on outside interface. There is correspoinding nat and global configured for outbound access to internet.
Now we need to terminate second ISP link on one of the DMZ interface to have redundancy for the primary ISP.
When primary ISP link or router is down we need to send all the traffic to secondary ISP router. How do we configure NAT and global for this condition that only when primary is down then only this NAT -Global should be used. Do we have anything like object tracking associated with the NAT-global.
So that as long as Primary RTR - object is up ASA will use the first NAT-Global pair. When primary ISP is down RTR-Object is not reachable then ASA will perform the second NAT-Global operation.
Also can we have default route pointing to Outside interface (primary ISP router) and in case of primary router failure it will point to secondary ISP. Do we have "track" in the static route commands on ASA.
View 2 Replies
View Related
Mar 23, 2013
May I know the reason why we cannot create interface vlan on Cisco ASA 5510?
View 2 Replies
View Related
Dec 20, 2011
FTP traffic routed from outside to the inside interface works fine. I have another interface with multiple sub-interfaces and vlans configured. FTP traffic routed from the outside to vlan2_servers is not making it through the firewall. I must be missing something. I have attached my config.
View 4 Replies
View Related
Jan 13, 2013
Whether it is possible to have same vlan on multiple interface on ASA 5510 and higher models ?
View 2 Replies
View Related
May 26, 2011
I am replacing an old Fw with a New ASA 5510 and I have a problem with a TCP Connection on My LAN InterfaceI joined a picture of what I want to do. [code] From the PC,I can Ping the Video Camera But I can't connect to it with HTTP.I don't understand, Packet Tracert allow the Http packet too. [code]
View 7 Replies
View Related
Jul 31, 2012
I have little experience with firewalls, what I've learned has been by dealing with issues like this that arise from time to time.I know, I need to upgrade the version. It's in the works now. Anyways, my question/problem is: Today I've received reports of slow internet access/activity and have noticed myself that it seems a bit slow today. On the dashboard of our asa 5510 the "outside interface" traffic usage is running contstantly high. It's at the top of the graph. How can I tell what is causing the spike in utilization. It usually runs at about 1500-2000 Kbps, and now it's up over 10,000.
View 2 Replies
View Related
Oct 25, 2012
I copied a Cisco 5510 startup-config to an identical Cisco 5510.After copying through tftp, I executed a reload. Everything looks good. Line by line compare results are the same.The problem is I can no longer use ASDM or ssh to interface with Cisco 5510.
View 25 Replies
View Related
Apr 13, 2013
I ran into a very strange icmp ping issue. The network has been working fine other than the issue listed below, L2L VPN works fine and all three data centers can access each other via L2L VPN.I have three ASA5510. [code]
View 5 Replies
View Related
Oct 21, 2012
I have two ASA 5510 in an active-standby cluster, not that I think that the fact that they are clustered will be of any importance here so feel free to think of it as a single 5510. The internet connection is delivered in a single RJ45 connection. To be able to use it with the cluster there is a simple unmanaged switch connected between the ISP and the ASA's. I have two subnets with public addresses, for simplicity lets call them 1.1.1.0/24 and 2.2.2.0/24. Default routers are 1.1.1.1 and 2.2.2.1 respectively.
Can I somehow use both these subnets in the ASA's? Im currently using the first subnet and use PAT to direct traffic to internal servers. But if I want to use adresses from the second subnet wont that mess up the routing, since there is no way I can specify the default router for the second subnet? I have as of yet not tried anything, Im just trying to plan ahead and I cant seem to wrap my head around how this could possibly be done.
View 5 Replies
View Related
Jan 16, 2012
I can't move traffic (isakmp udp_port: 500 & ipsec nat traverse udp_port: 4500) from my dmz to the outside interface
View 1 Replies
View Related
Feb 24, 2011
I have disabled Unicast RPF on a Cisco ASA 5510 for one specific interface. However, how do I verify that RPF indeed has been disabled on that particular interface? It doesn't show up in the config, neither does it up when I issue the command "sh int interface'.
To disable the RPF feature, I issued the following command: no ip verify reverse-path interface interface_name
View 1 Replies
View Related
Feb 5, 2012
i have here a ASA 5510 sec k9.
I build a Config with a DMZ,INSIDE and OUTSIDE Interface. My Plan is to use the IP-Address of the OUTSIDE Interface with PORT to setup a HTTP Server In the DMZ
But my Config doesn't work. And I have no Plan why .....
The Inside Interface have to work normal. The Traffic to the Internet is TRiggert from Inside with Dynamic PAT
ciscoasa(config)# exit
ciscoasa# show run
: Saved
:
ASA Version 8.4(1)
[Code].....
View 2 Replies
View Related
Jun 11, 2012
I working on a security solution using ASA firewall. Is it possible to setup a IPSec tunnels on each subinterface of a physical interface on ASA 5510?
View 3 Replies
View Related
Apr 4, 2012
The ASA is configured in very simple transparent mode. As desired, traffic can flow in each direction between inside and outside. I can manage the ASA via console and direct connection to the management interface. The problem is that I cannot ping or ssh to the ASA via the inside interface. I need to be able to manage the ASA from any PC on the inside LAN. I suspect I am missing some easy aspect of the configuration but after a lot of hours I'm about at the end of my patience with it. Here is what I believe to be the relevant parts of the config.
ASA Version 8.2(1)
!
firewall transparent
hostname issr1
enable password 2alej83t5cqT0FWd encrypted
passwd 4kleUY438I93.4ljdh encrypted
names
[code]....
View 4 Replies
View Related
Jun 28, 2012
we have a server that has an outside IP and an inside IP. It's inside ip is 192.168.222.30/24 and it's outside IP is 199.204.50.2/29. The connection to this server from the outside is perfectly fine, but access from inside users to the NAT'd IP which is 199.204.50.2/29 is having issues, however, access to the inside IP works fine (this part makes sense)Will It be a must to set the inside DNS A record to the inside IP and not the outside IP, or can users on the inside interface access the NAT'd IP which is assigned to the server
LAN(192.168.222.0/24)<=====>InsideASAOutside<=====>(Server with NAT IP 192.168.222.30/24, it's also physicall assigned to this server).This is an ASA 5510 with 8.4.
View 10 Replies
View Related
Dec 26, 2011
I have a Cisco ASA 5510 connected to 2 private lans (1 for my HQ pc's{inside} and 1 for the worldwide mpls{outside}) It is also connected to the public internet at interface "public" and my dmz at "dmz" interface. I suspect I have a routing issue because packet-trace yields allow, the nat looks ok and the objects look ok at least to me but I'm the one with the non working config so...Basically this is the desired flow:
1. I need all traffic from the inside to be able to flow to the outside unimpeded as they are both trusted networks. (this is ok right now as I allow everything via access-list 101.)
2. I need any host on the public internet to be able to reach a server on the dmz via the pat which I set up from the "public" interface to the "DMZ" interface. The desired flow would be that the person on the internet types in [URL] and this is directed to the public interface ip which forwards to the webserver object on the dmz. (I cannot get this working any which way)
3. I need the dmz to be able to communicate with another server on the mpls via the "outside" interface when it recieves the request from the public it then checks with this other server on the outside via nat(translating the dmz range into the ip of the outside interface on the firewall)I have a default route that points to the mpls or outside interface for 0.0.0.0 0.0.0.0 via 10.x.x.1 - (and although I'm not sure I suspect this could be conflicting with traffic that needs to be sent to the "public" interface .... meaning that the firewall should dump packets bound for 0.0.0.0 0.0.0.0 to the public interface - 184.x.x.194 but I'm very reluctant to change the default route as this is in production and I'm not sure how it will affect traffic).However, I do suspect that if I changed the route from default to static as such:
route 10.0.0.0 255.0.0.0 10.x.x.1 (this would get all lan and mpls traffic to the mpls gateway) route 0.0.0.0 0.0.0.0 184.x.x.193 (this would send everything else from public to the public internet gateway)I think this is accurate but then I would bypassing my corporate internet proxy which is behind the mpls gateway at 10.x.x.1? Is there a way to get http traffic originating from the lan (10.x.x.x) to use the mpls gateway and http traffic for the dmz to use the public internet gateway at 184.x.x.193. I don't want to start causing a flow problem for the internet nor do I want to bypass my corp internet proxy.Either way I cannot get this to work, eventhough the logic checks out, I cannot get even a ping response when I allow icmp any any for testing. Note: I can ping resources on each network from the firewall, not only it's own ports in the associated network but other resources on those networks as well.
Here is the running-config:
ciscoasa# sho run
: Saved
:
ASA Version 8.4(1)
!
hostname ciscoasa
domain-name marcjacobs.lvmh
[code].....
View 16 Replies
View Related
Jan 24, 2013
I am attempting to set up FTP behind this new CISCO ASA 5510 we just bought. I haven't configured a cisco device in 5 years, so I am having issues., i think i am close. If I FTP from outside (fixed) IP it connects and takes the password but hangs on PASV and gives no data connection below is my configuration. It is simple since I seem to have the connection inside correct. and yes you can connect to the FTP server from inside without issue.
Code...
View 4 Replies
View Related
Jul 24, 2012
I have one Asa 5510 with base license. now we wish to add one back up ISP for VPN fail over, is this possible to configure backup ISP with this ASA 5510 and how ?
Check ASA features
Cisco Adaptive Security Appliance Software Version 8.2(2)
Device Manager Version 6.2(1)
Compiled on Mon 11-Jan-10 14:19 by builders
System image file is "disk0:/asa822-k8.bin"
Config file at boot was "startup-config"
Cisco asa up 3 hours 35 min
Hardware: ASA5510, 1024 MB RAM, CPU Pentium 4 Celeron 1600 MHz
Internal ATA Compact Flash, 256MB
BIOS Flash Firmware Hub @ 0xffe00000, 1024KB
View 3 Replies
View Related
Jun 11, 2009
We have some users who use citrix outside corporate network through citrix web interface.These users are high priority users and we want to prioritize the citrix traffic. I want to make sure that my configuration will fullfill our requirements. Below is the configuration i was thinking to implement.:
ASA(config)# priority-queue outside
ASA(config-priority-queue)# exit
ASA(config)#access-list CTX-QoS extended permit tcp any 10.1.1.200
255.255.255.255 eq https
ASA(config)# class-map CTX-QoS-CMAP
ASA(config-cmap)# match dscp ef
ASA(config-cmap)# match access-list CTX-QoS
ASA(config-cmap)# exit
ASA(config)# policy-map CTX-QoS-PolicyMap
ASA(config-pmap)# class CTX-QoS-CMAP
ASA(config-pmap-c)# priority
ASA(config-pmap-c)# exit
ASA(config)# service-policy CTX-QoS-PolicyMap interface outside
View 3 Replies
View Related
