Cisco Switching/Routing :: 2955 - Send Configuration Changes To Syslog Server?
Apr 27, 2012
I can't seem to send config changes to our syslog server on a 2950, I'm fine with 2960's and 3750's. The Cisco 2955 is using the latest IOS c2955-i6k2l2q4-mz.121-22.EA14.bin.
Here is what I have added:
logging buffered 64000 debugging
logging console informational
logging monitor informational
[Code].....
The only sylog message I get is "Configured from console by username on vty0 (10.1.1.35)
View 5 Replies
ADVERTISEMENT
Dec 21, 2011
I have configured my 2951 router to send logs to my Kiwi syslog server like below.
#logging 10.20.20.52
But I am not receiving any logs from my router, the same has configured on my asa5520 and its sending logs.
View 3 Replies
View Related
Dec 15, 2012
I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
View 2 Replies
View Related
Jul 2, 2012
Query is, Can i send my syslog messages to SNMP sever? if so, what command needs to be enabled on nexus 7k?
View 3 Replies
View Related
Mar 9, 2013
I'm having an issue with the syslog.
My configuration is:
LAN A (RV042)<-> GW to GW tunnel <-> (RV082) LAN B
On LAN A, I got a NAS with a syslog server. On the RV042, I've set the parameters for the syslog server, and it's working fine. On the RV082, I've set the same parameters and noting is happening.
As troubleshooting, I've done the following:
-On the RV082, I can ping the NAS without problems.
-On the RV082, I've set my computer IP adress as syslog server IP and with packet analyser, I not seing any UDP packets.
View 6 Replies
View Related
Aug 8, 2011
Can i send "show conn" to syslog server? for example:
[code]...
ESTAB5082
View 1 Replies
View Related
Jul 7, 2012
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies
View Related
Sep 10, 2012
we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
View 3 Replies
View Related
Feb 5, 2012
I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?
View 6 Replies
View Related
May 5, 2013
I'm trying to view the logs from a Cisco 857W router to a workstation running the Kiwi Syslog server. what I've done is the following:
Config term
Logging on
Logging source-interface BVI1
Logging Facility Local7 (or any other facility you want to allocate for this router.)
Logging [IP Address or Hostname of machine running Kiwi Syslog Server]
End
I see noting on the syslog server. Although I can see the log information on the router Also is there a command to stop the logging from generating or is this on by default.
View 1 Replies
View Related
Apr 16, 2013
I have installed a switch (3560) that was from another site and changed all it's config and hostname etc and it is now live, however the syslog messages still see the old hostname, what could be causing this?
View 3 Replies
View Related
Apr 5, 2012
I'm been telnetting onto a 2955 and then upgraded the IOS and enabled ssh version 2 and then issues a "write", when I came back the exec-timeout had been issued and I was logged out of the router and now it is asking for a username and password and not just a password liek it did before enabling ssh. I havent yet put a username and password on yet, just the telnet.What would the username be if I havent set one?
View 12 Replies
View Related
May 2, 2012
I'm on a Cisco 2955 switch and need to get ssh working which I have done on another 2955 (but don't have near me), what am I doing wrong?
2955-02-PJ-CamdT.LU#sh run Building configuration...
Current configuration : 4061 bytes!version 12.1no service padservice timestamps debug datetime msec [code]....
View 4 Replies
View Related
Apr 15, 2012
I'm trying to allow 2 users to access as 2955 switch.
-admin privilege 15
-eousers privilege 2
When they both log in they just get to the user exec mode, how can I get them to go to their respective modes? [code]
View 1 Replies
View Related
Apr 3, 2012
I'm about to configure radius on a 2960 and 2955 switch as I have been testing this on a 1841 router and to my dismay I can't see the options to configure radius, do these L2 switches not supoprt radius?
edit - apoligies I forgot the "aaa new-model" all ok now
Although when I added:
radius-server host 10.1.1.1 auth-port 1645 acct-port 1646 key 123456789
radius-server host 10.1.1.2 auth-port 1645 acct-port 1646 key 123456789
radius-server vsa send accountingradius-server vsa send authentication
I got this:
Warning: This CLI will be deprecated soon. Please move to radius server <name> CLI.
And what woudl the above look like if I configured it that way?
View 6 Replies
View Related
Jan 21, 2013
I have installed Cisco 2955 Switch which already have x.x.x.x EA12 IOS and I copied x.x.x.x.EA13 into the flash: with intention to have EA13 enabled for IOS. I set the Global config for boot system by 'boot system (no falsh)x.x.EA13;x.x.EA12' but then also no luck and was showing EA12 in 'sh ver'. I then deleted the EA12 IOS and set the 'boot system flash:x.x.EA13'. I also had varified IOS EA13 by 'verify flash:IOS Filename', it verified the IOS.
But when I reloaded my switch, I'm unable to login and its in 'switch:' prompt (ROMmon mode - I believe). I then tried for flash_init, load_helper, dir flash: (showing me EA13 there) and finally boot flash:IOS Image file but no good news here... Output like this
Error loading "flash:IOS Image File EA13" Interrupt within 5 seconds to abort boot process. Error loading "flash:c2950-i6q4l2-mz.121-12c.EA1.bin"Interrupt within 5 seconds to abort boot process.
My guessing is that the IOS is corrupted (but its not showing me Error loading Image blabla...) I'm trying with EA14 of 4MB and I have 3 MB free spare and decided to remove EA13 first then through XModem try to upload EA14.
Any useful way and recommend me deleting EA13 and upgrading EA14... Also option to set boot image with having two IOS at the same time for permanent use.
View 5 Replies
View Related
Jan 15, 2012
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies
View Related
Feb 6, 2012
I come across to use the Catalyst Switch 2955 and it has two Relay Connector with one Major (MAJ) and one Minor (MIN) as below picture.There is command line to trigger these two Relay Connectors. As below command to set the Relay Connector to minor for monitoring the power supply: alarm facility power-supply relay minor
1. My questions are when there is power-supply faulty, the Minor Relay Connctor (right picture) will be short-circuited, right?
2. If we connector the two ports (ports 4 & 5 at the left picture) with a normal cable to drive an Alram Bell (in short-circuiled or closed loop situation), do we need an external power supply to the Alram Bell? Or there will be power supply from Catalyst 2955 to the Alram Bell as well?
View 1 Replies
View Related
Oct 25, 2011
I am having an issue with this device after setting the ip address and rebooting. I have tried renaming the config.text file without success. I have also tried the steps mentioned here: [URL]
View 1 Replies
View Related
Nov 3, 2012
I have found that the Catalyst 2955 series switches do not use an external MODE button for getting a switch into the switch: prompt, but they use a break sequence like routers do to get into Rommon state URL
So I was wondering if there is a similar mecanism that applies to other kind of Catalyst switches, like 2960, 3560 or 3750.
View 7 Replies
View Related
May 20, 2012
I need to only allow 5 Mac Addresses on a range of ports on a 2955 switch. If I do the following it only changes the first port in the range:
interface range fastEthernet 0/5 - 10
no spanning-tree portfastswitchport port-securityswitchport port-security maximum 5switchport port-security violation restrictswitchport port-security mac-address 00:1D:24:25:F7:AA
[Code].....
View 2 Replies
View Related
Feb 5, 2012
One of my clients is using Cisco catalyst 2955 industrial switch.I am doing the configuration for them and come across one setting of FCS Error Hysterasis Threshold. I know FCS is Frame Check Sequence.
I do not understand is what is the meaning the setting of Hysteresis in term of percentage stand for what purpose?For example, the default is 10 percent. If I set the value to be lower 5% and what is the impact on that? Is this more stringent than default of 10% or less stringent than default of 10%?
View 4 Replies
View Related
Dec 4, 2011
how can I configure ACS 5.2 to send syslog messages to CS-MARS?
View 3 Replies
View Related
Mar 5, 2013
I absolutely need to collect the router logs and send them to a syslog daemon or via email.
View 9 Replies
View Related
Jul 24, 2012
I am trying to connect my Access Server to my main network via the AUI port and I am not able to ping any device..
Current Config:
Access_Server#show run
Building configuration...
Current configuration : 1113 bytes
!
version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
[code].....
View 14 Replies
View Related
Dec 6, 2012
what is the best configuration between vmware ESX server with 10 Physical NIC card and cisco 6500 , This ESX Server host 12 vm with VLAN 100,150.200.
View 6 Replies
View Related
Feb 28, 2012
We had core(4503), distribution(3750), and access switches(2960) in our environment. Currently we configured the clock manually in each switch, but a reboot of the switch resets the clock also. We are planning to make a single switch as a NTP servers and others are clients to synchronise the correct time even after a reboot of the access switches.
View 6 Replies
View Related
Apr 12, 2012
I need to transfer a config from a TFTP Server to a 4507 and a 6513. When I transfer the config to both those switches, does it require a reboot?
View 5 Replies
View Related
Jan 28, 2013
I am going to creat VLANs very 1st time therefore for test purpose I have following simple scnerio.I have created 2 VLANs , VLAN2 and VLAN3 on Cisco Catalyst 2960 series switch. Ports 1-12 is assigned to VLAN2 and Ports 13-24 are assiged to VLAN3. Now I have configured DHCP on Microsoft Server 2003 defining 2 scopes with following configurations.
Scope 1 for VLAN 2--- Range is 172.16.0.17 to 172.16.0.30 with subnet mask=255.255.255.240 . Server IP address 172.16.0.17
( Note: Address 172.16.0.17 is excluded from dhcp server Scope 1 and give to the MS server itself)
Scope 2 for VLAN 3----Range is 172.16.0.33 to 172.16.0.46 with subnet mask=255.255.255.240 .
Now in Cisco 2960 series switches, under Vlan 2 and Vlan 3, I have following configurations...
interface Vlan2
ip address 172.16.0.30 255.255.255.240
ip helper-address 172.16.0.17
interface Vlan3
ip address 172.16.0.46 255.255.255.240
ip helper-address 172.16.0.17
Now the problem is when i connect a client computer to any port from 1-12, It gets correct IP address from Scope 1 but when I connect a computer to any port from 13-24, it does not get the ip address.
Further I want to do inter VLAN comunication as well for that purpose i Have an ISR 2900 series router. What further configuration i will have to do on router for inter vlan communication.
View 3 Replies
View Related
Feb 22, 2013
I came across an interesting issue and thought I would see if anyone else has encountered it before contacting TAC.I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54).
View 2 Replies
View Related
Apr 23, 2012
I have two Cisco Catalyst WS-4510R-E switches with a single Supervisor V module in each chassis. Both Sup cards are now running 12.2(54) SG1; ipbasek9 firmware; yes, I plan to move both switches to 15 code but that's another story. Anyways, prior to the upgrade the one switch was running 12.2 (33) code; I suspect the code was never upgraded; running ipbase non - K9 code. The other switch was running 12.2(44) with K9 prior to upgrade to 12.2(54). With the background set, one switch reports the following:SwitchA (config)#r?radius-server redundancy regexp represourc rmon route-map router.
View 4 Replies
View Related
Feb 11, 2012
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies
View Related
Mar 30, 2013
how to enable snmp traps for syslog message in Cisco Nexus platform ?
Mean what would be equivalent CLI for the below
"snmp-server enable traps syslog"
View 2 Replies
View Related
