Cisco AAA/Identity/Nac :: Configure ACS 5.2 To Send Syslog Messages To CS-MARS?
Dec 4, 2011how can I configure ACS 5.2 to send syslog messages to CS-MARS?
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Nexus 7k - Possible To Send Syslog Messages To SNMP Sever
Jul 2, 2012Query is, Can i send my syslog messages to SNMP sever? if so, what command needs to be enabled on nexus 7k?
View 3 Replies View RelatedCisco Switching/Routing :: 1841 - Unable To Make Router To Send Syslog Messages To Server
Dec 15, 2012I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
Cisco :: 2650 XM - Configure IP SLA To Generate Syslog Messages
May 19, 2010I want to use IP SLA to perform simple up/down monitoring of an IP host and to generate a syslog alert if the host goes down. I have a 2650XM router running 12.4(23) IP Voice IOS. My basic IP SLA config is hown below:
ip sla monitor 10
type echo protocol ipIcmpEcho 10.55.1.1
timeout 1000
frequency 10
ip sla monitor schedule 10 life forever start-time now.
Cisco Switching/Routing :: Configure 2951 To Send Logs To Kiwi Syslog Server?
Dec 21, 2011I have configured my 2951 router to send logs to my Kiwi syslog server like below.
#logging 10.20.20.52
But I am not receiving any logs from my router, the same has configured on my asa5520 and its sending logs.
Cisco Routers :: SA 500 - Ability To Send Syslog Events To Multiple Syslog Servers
Jul 7, 2012Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies View RelatedD-Link DIR-655 :: What Does Syslog Messages Mean
Jul 26, 2012I'm getting the Syslog messages frequently on daily basis.
View 4 Replies View RelatedCisco :: LMS 4.2 Not Processing Syslog Messages
Mar 12, 2012I have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies View RelatedCisco :: LMS 4.1 - No Syslog Messages Appearing?
Sep 28, 2011LMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies View RelatedCisco :: LMS 4.0.1 Not Processing Syslog Messages
Jun 19, 2012My Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies View RelatedCisco :: Syslog Messages Not Showing With LMS 4.1
Mar 3, 2013I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
Cisco :: LMS 3.2 - Invalid Syslog Messages
Aug 22, 2011I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
Cisco :: Debug Syslog Messages In Router
Jun 26, 2012Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedCisco Switching/Routing :: Way To Get More Messages Out Of 2950 Set To Syslog
Feb 11, 2012Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies View RelatedCisco Routers :: RV110W Excessive Syslog Messages?
Mar 6, 2012I bought a RV110W wireless router a couple months ago that I've been pretty happy with.
However, I have one significant problem with it. It is configured to send syslog messages to an internal server. Twice now it has gone into a mode where it starts dumping messages like,
ip_conntrack_is_ipc_allowed: ipc_entry_is_full
continuously, at a rate of about 20 per second. It otherwise seems to function normally, but of course if unnoticed my syslog file quickly grows to hundreds or thousands of megabytes. A reboot restores normal operation. It is running firmware 1.1.0.9. A search on the internet turned up no information about this problem.
It may be some corruption is occuring in the router's OS, or perhaps this is something that can be triggered externally (in which case it would be a weak form of DoS attack? Or maybe worse if in this state it is unable to properly apply the firewall rules.)
Cisco Firewall :: ASA 5520 Error Syslog Messages
May 10, 2012We started getting the below syslog messages from one of our ASA5520 which was recently upgraded to 8.4(2). Any bugs on 8.4(2) that cause this or its simply the RAM failure?
%ASA-3-105010: (Primary) Failover message block alloc failed
%ASA-3-321007: System is low on free memory blocks of size 1550 (0 CNT out of 18709 MAX)
Cisco :: Can IPM LMS 4.1 Send Messages Or Traps
Dec 21, 2011We need IPM (LMS 4.1) to send and e-mail, sms o trap to NNM, is it possible??
View 2 Replies View RelatedCisco :: Detecting Rogue AP Messages In Syslog And Configuring WLC 5500
May 7, 2013I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior. I'm doing this step.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the URL
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it.URL
NOTE: from the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired
I don't think i completely understand this statement, by sitting does it mean that it is passively sniffing coming in/out on trunk link?
Considering the above steps are accurate, after this will i be able to see rogue detection behavior in syslogs? What exactly would be the messages that would produce this behavior.
How To Send Messages On Outlook Using Wifi
Dec 4, 2012I am using a verizon wifi unit. I us outlook 2007. I can receive emails but I cannot send emails. How can I adjust the settings to send emails using my wifi?
View 3 Replies View RelatedCisco Switching/Routing :: 9500 Is It Possible To Change UDP Port For Syslog Messages
Jun 12, 2012Is there any way to change the port that is used for syslog messages on a Cisco 9500 switch?By default this is set to UDP port 514.There doesn't seem to be a command to change the port.
View 1 Replies View RelatedCisco WAN :: 7600 / Syslog Doesn't Display Informational Level Messages
Mar 27, 2012I have an issue with the syslog of 7600 router, I have configured the logging level to informational, but when I execute changes such as up or down an interface, the syslog messages aren't displayed? Why is the reason? This symptom exist after I changed the buffer size from default to 32768.
Router#sh log
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 2 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 40 messages logged, xml disabled,
[code]....
Cisco Wireless :: 5500 Detecting Rogue AP Messages In Syslog / Configuring WLC
May 9, 2013I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the WLC. url...
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it. url...the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired.
Linksys Cable / DSL :: How To Send Messages Log With Wag160
Jan 2, 2012on the reporting tab, a button gives access to the log. Is it possible to retrieve this log file in order to submit it to a specialist ?
View 3 Replies View RelatedDHCP - Which OS Actually Send Out Release Messages As Part Of Shutdown Sequence
Mar 2, 2012I've heard mixed things about the use of DHCP release messages. I've heard that some operating systems don't bother with them at all, which makes sense because many users disconnect the network media without shutting down the workstation. Which operating systems actually send out release messages as part of their shutdown sequence?
View 5 Replies View RelatedCisco Firewall :: FWSM 4.1 How To Send Mail Messages When Fail Over Occurs
Feb 16, 2012We are using FWSM with software version 4.1(6) with failover and multi contexts.We need to generate and send mail notifications when failover occurs.
With this configuration we are receiving syslog only! [code]
Cisco Routers :: Cannot Send Syslog To Server From A RV082
Mar 9, 2013I'm having an issue with the syslog.
My configuration is:
LAN A (RV042)<-> GW to GW tunnel <-> (RV082) LAN B
On LAN A, I got a NAS with a syslog server. On the RV042, I've set the parameters for the syslog server, and it's working fine. On the RV082, I've set the same parameters and noting is happening.
As troubleshooting, I've done the following:
-On the RV082, I can ping the NAS without problems.
-On the RV082, I've set my computer IP adress as syslog server IP and with packet analyser, I not seing any UDP packets.
Cisco Switching/Routing :: 2955 - Send Configuration Changes To Syslog Server?
Apr 27, 2012I can't seem to send config changes to our syslog server on a 2950, I'm fine with 2960's and 3750's. The Cisco 2955 is using the latest IOS c2955-i6k2l2q4-mz.121-22.EA14.bin.
Here is what I have added:
logging buffered 64000 debugging
logging console informational
logging monitor informational
[Code].....
The only sylog message I get is "Configured from console by username on vty0 (10.1.1.35)
Cisco Application :: 5082 - Send Show Connection To Syslog Server?
Aug 8, 2011Can i send "show conn" to syslog server? for example:
[code]...
ESTAB5082
Linksys Wireless Router :: EA4500 / How To Send Logs To Syslog Or Via Email
Mar 5, 2013I absolutely need to collect the router logs and send them to a syslog daemon or via email.
View 9 Replies View RelatedCisco AAA/Identity/Nac :: Syslog Configuration In ACS 5.2.0.26?
Feb 18, 2012I want send ACS logs to a syslog server .I have configured syslog under System Administration --> Configuration -->Remote Log Targets .
Name : Syslog Server
IP : x.x.x.x
Port : 514
Facility Code:Local 6
Maximum length :1024
I have open the respective ports also in firewall .But Syslog server is not getting any logs from ACS .I have another log target ,which is ACS secondary server to collect the log from primary and secondary with below config.whch is working fine
Name :Logcollector
IP : x.x.x.x
Port : 20514
Facility Code:Local 6
Maximum length :1024
Cisco Switching/Routing :: Configure 6500 To Respond To Messages As NTP Master
Feb 12, 2013Setting up NTP. Currently the source for NTP within our network is our core 6500.Currently the NTP source for the 6500 are internet based NTP Servers. I would like to configure the 6500 to respond to NTP messages as the NTP Master. However will the 6500's source remain as the internet based NTP Servers?? In other words if the 6500is configured to be NTP Master, where would it get it's time from?
View 5 Replies View RelatedCisco Firewall :: Can Configure More Than One Syslog Host On ASA 5500
May 31, 2012I would like to send my ASA 5500 logs to more than one syslog server - is this possible? I can't seem to find it in the documentation.
View 3 Replies View RelatedCisco :: How To Configure LMS 4.0 To Capture Syslog From Network Devices
Aug 23, 2011How can I configure my LMS 4.0 to capture syslog from network devices?
On the LMS CiscoWorks Portal, Syslog Alert window shows "No data is available".