Cisco WAN :: 7600 / Syslog Doesn't Display Informational Level Messages
Mar 27, 2012
I have an issue with the syslog of 7600 router, I have configured the logging level to informational, but when I execute changes such as up or down an interface, the syslog messages aren't displayed? Why is the reason? This symptom exist after I changed the buffer size from default to 32768.
Router#sh log
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 2 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 40 messages logged, xml disabled,
[code]....
View 4 Replies
ADVERTISEMENT
May 9, 2012
I have a situation in which I want to log a specific message (informational - 6 level), but don't want to enable informational logging and get all the messages that come with it. Is there a feature in IOS, 3560 12.2(25r)SEE4, similar to the 'logging lists' feature on the ASA that allows you to specify logs that you want to capture without having to change your logging level? I didn't want to have to write an EEM applet for this, but if that's the only way, I'd consider it.
View 3 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Jul 26, 2012
I'm getting the Syslog messages frequently on daily basis.
View 4 Replies
View Related
Mar 12, 2012
I have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies
View Related
Sep 28, 2011
LMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies
View Related
Jun 19, 2012
My Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies
View Related
Mar 3, 2013
I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
View 0 Replies
View Related
Aug 22, 2011
I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
View 1 Replies
View Related
Mar 5, 2012
I'm fine tuning some of our ASA logging config, and am having an issue with one particular syslog ID.The message is: syslog 106100: default-level informational (enabled)and the log settings are:
Syslog logging: enabled
Facility: 20
Timestamp logging: enabled
Standby logging: disabled
Debug-trace logging: disabled
[code]....
This ACE log entry is generated by explicit deny any any statements at the end of all the ACLs, e.g.access-list inside_access_in extended deny ip any any log interval 600 Based on the config, I would expect to see this being logged to the syslog server, but not to the local buffer, but am still seeing them locally in the buffer:
Feb 22 2012 10:58:20: %ASA-4-106100: access-list inside_access_in denied udp INSIDE/HOSTABC(52629) -> OUTSIDE/HOSTXXX(162) hit-cnt 5 300-second interval [0x3baecf1e, 0x0]
It also still shows these as level "warning", %ASA-4-106100, instead of the default %ASA-6-106100 I've tried removing and re-applying the config at different levels but it still reports in the buffer log as level "warning", %ASA-4-106100 This also doesnt affect every 106100 log that is generated. Most messages are generated at the correct level 6 severity but some seem to randomly log at level 4. There doesn't seem to be any pattern to this. The same access-list line can produce severity level 4 and 6 106100 messages.
View 2 Replies
View Related
Jun 26, 2012
Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies
View Related
Feb 11, 2012
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies
View Related
Mar 6, 2012
I bought a RV110W wireless router a couple months ago that I've been pretty happy with.
However, I have one significant problem with it. It is configured to send syslog messages to an internal server. Twice now it has gone into a mode where it starts dumping messages like,
ip_conntrack_is_ipc_allowed: ipc_entry_is_full
continuously, at a rate of about 20 per second. It otherwise seems to function normally, but of course if unnoticed my syslog file quickly grows to hundreds or thousands of megabytes. A reboot restores normal operation. It is running firmware 1.1.0.9. A search on the internet turned up no information about this problem.
It may be some corruption is occuring in the router's OS, or perhaps this is something that can be triggered externally (in which case it would be a weak form of DoS attack? Or maybe worse if in this state it is unable to properly apply the firewall rules.)
View 2 Replies
View Related
May 19, 2010
I want to use IP SLA to perform simple up/down monitoring of an IP host and to generate a syslog alert if the host goes down. I have a 2650XM router running 12.4(23) IP Voice IOS. My basic IP SLA config is hown below:
ip sla monitor 10
type echo protocol ipIcmpEcho 10.55.1.1
timeout 1000
frequency 10
ip sla monitor schedule 10 life forever start-time now.
View 7 Replies
View Related
May 10, 2012
We started getting the below syslog messages from one of our ASA5520 which was recently upgraded to 8.4(2). Any bugs on 8.4(2) that cause this or its simply the RAM failure?
%ASA-3-105010: (Primary) Failover message block alloc failed
%ASA-3-321007: System is low on free memory blocks of size 1550 (0 CNT out of 18709 MAX)
View 2 Replies
View Related
Dec 4, 2011
how can I configure ACS 5.2 to send syslog messages to CS-MARS?
View 3 Replies
View Related
May 7, 2013
I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior. I'm doing this step.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the URL
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it.URL
NOTE: from the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired
I don't think i completely understand this statement, by sitting does it mean that it is passively sniffing coming in/out on trunk link?
Considering the above steps are accurate, after this will i be able to see rogue detection behavior in syslogs? What exactly would be the messages that would produce this behavior.
View 7 Replies
View Related
Jun 12, 2012
Is there any way to change the port that is used for syslog messages on a Cisco 9500 switch?By default this is set to UDP port 514.There doesn't seem to be a command to change the port.
View 1 Replies
View Related
May 9, 2013
I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the WLC. url...
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it. url...the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired.
View 2 Replies
View Related
Jul 2, 2012
Query is, Can i send my syslog messages to SNMP sever? if so, what command needs to be enabled on nexus 7k?
View 3 Replies
View Related
Dec 15, 2012
I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
View 2 Replies
View Related
Apr 28, 2013
I've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
View 5 Replies
View Related
May 21, 2013
my LMS 4.2, syslog collector on LMS doesnt working even service syslog collector running normaly and also i saw in syslog_info is working to collect syslog from all router but not show up in dashboard monitoring.I have setting on every router to logging (ip address LMS) but on LMS no any syslog from router can collect.i did a selftest from LMS there are all PASS except nslookup fail, it is has relation with syslog not show up on dashboard?
View 5 Replies
View Related
Sep 30, 2011
I have extension mobility configured and working fine. Except that when you log into the phone, the phone does not exit back to the main display. To get back you either need to exit out of the menus by pressing exit a few times or press the globe / web button on the phone.
View 6 Replies
View Related
Mar 13, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
View 2 Replies
View Related
Jul 2, 2011
My router is the WRT160N, and it doesn't display the version number on the bottom which according to your website means my router is a VERSION 1.SO, why is it that my router says it has:
Firmware Version: v1.53.0 Dec 19, 2007
And the latest firmware is
Firmware 11/08/2010 Ver.1.02.11
That looks like an EARLIER firmware version to me judging by the firmware version yet it is dated later. **bleep**. If you want, I can upload a photo of my router's model no. for all to see.My question is, am I safe to 'upgrade' to this 'earlier but dated later' firmware version or not? Why is mine showing as having a later version.
View 4 Replies
View Related
Sep 10, 2012
we've been using IOS for a long time, but are relatively new to NX-OS. We've got a central syslog server that all our devices log to. No matter what we do, we can't get our Nexus switches to log there. Here's my current attempt:
Nexus 7009, NX-OS 6.0(1)
# sh logging server
Logging server: enabled
{redacted}
server severity: debugging
server facility: local7
server VRF: default
[code].....
The default VRF is working. I see log entries in the logfile, but nothing arrives at the syslog server. It's not a config issue on the server, because tcpdump shows that no packets arrive from the IP for loopback 0.
View 3 Replies
View Related
Jul 7, 2012
Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers. I know the functionality is currently in the RV220W because we utilized it. It would be great if you could configure the syslog servers by event type as well. For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.
View 0 Replies
View Related
Jan 15, 2012
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies
View Related
Dec 12, 2010
what ios for 827-4v from 12.4 can i use for IPSEC+ddns?i tested some from 12.4 but normally working only 12.3(26)GD, but i want ddns feature? some from 12.4 is working with tracebacks, other is not loading - with error (loadprog: error - program section linked to illegal address)
View 4 Replies
View Related
Jan 18, 2012
We have a 7206VXR with an NPE-G1 processor. We're running the standard stuff on it, but here are the highlights.We just enabled netflow on it to send the data to an external source for analysis and the overall CPU level increased, but not significantly. About what should we expect for the overall CPU level? At this point, it's averaging close to 40% during peak hours.
View 4 Replies
View Related
Jun 27, 2011
I have ASA 5505 that has two inside security level 100 interfaces and an outside interface.On the inside interface we have corporate domain subnet with DC and 30 hosts. On the inside2 interface I have few servers that runs specific application important for our business needs, and dumb terminals that are connected to them.I have a laptop user that periodically needs access from our corporate vlan1 to one of the servers on inside 2 vlan via remote desktop or some other remote viewer client,so he can view reports etc.I have enabled same-security-traffic intra-interface command and added nat exempt command pointing specific laptop host machine to that specific server.
Now my main concern is regarding security. This user carries his laptop home, browses the web, puts USB memory, and you can imagine how this machine is susceptible to all kind of malicious software. Inside2 vlan is very important and until now it has been a very secure environment.This is no longer the case since all traffic between this inside sec level 100 vlan host and corresponding inside2 sec level 100 server is now allowed because of the enabled same level interface traffic and nat exemption rule. Do I have another solution that would allow communication based on just a tcp port number for this host? Something like port forwarding from outside to inside Vlan interface?
View 10 Replies
View Related
Jun 13, 2011
I have cisco ACS 5.2 and external identity source as RSA secure ID.Currently when the RSA user login to AAA Network devices, User id & passcode prompt coming after giving the credential its going to user exec mode.Then after "enable" command again asking for Passcode giving passcode then user able to logged in successfully.
I need RSA users to get direct privlege level15 (privlege mode) ? no need to ask enable password ?
I checked this for local ACS users it is working and loca users getting directly privelege mode access...
View 2 Replies
View Related
