Cisco WAN :: New 1921 Doesn't Display Running Configuration
Apr 28, 2013
I've recently received this new Cisco 1921 routers with Cisco CP loaded, so it comes up with the annoying change username and password at first access. I've removed all of those files from the flash memory, and rebooted it, and it came up with the proper initial configuration dialog, which is what I wanted. But, whenever I configure the router with a set of basic configuration, like interface, routing, and snmp loggings, and hit wr mem, it doesn't display at all when I do "sh run". It's weird cause when I do sh run | sec rip or any other stuff that I have configured, it shows up , but not in sh run at all.
What's the deal with the new routers? Even sh version doesn't show the config-register or memory allocation details.
xxxxx#sh ver
Cisco IOS Software, C1900 Software (C1900-UNIVERSALK9-M), Version 15.1(4)M4, RELEASE SOFTWARE (fc1)
Technical Support: [URL]
[Code].....
View 5 Replies
ADVERTISEMENT
Jun 11, 2013
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies
View Related
May 7, 2013
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies
View Related
Sep 30, 2011
I have extension mobility configured and working fine. Except that when you log into the phone, the phone does not exit back to the main display. To get back you either need to exit out of the menus by pressing exit a few times or press the globe / web button on the phone.
View 6 Replies
View Related
Mar 27, 2012
I have an issue with the syslog of 7600 router, I have configured the logging level to informational, but when I execute changes such as up or down an interface, the syslog messages aren't displayed? Why is the reason? This symptom exist after I changed the buffer size from default to 32768.
Router#sh log
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 2 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 40 messages logged, xml disabled,
[code]....
View 4 Replies
View Related
Mar 13, 2013
Region : UnitedKingdom
Model : TD-W8970
Hardware Version : V1
Firmware Version : 0.6.0 0.11 v000c.0 Build 121203 Rel.46289n
ISP :
However, when I initially connect to the router, either on the LAN or remotely via the internet, the router takes a long time to display the initial page (up to 1 minute) and then usually displays the page without any variable data included. Frequently it also fails to show the menu on the left either. By hitting Refresh several times, eventually it will load the page fully.
View 2 Replies
View Related
Jul 2, 2011
My router is the WRT160N, and it doesn't display the version number on the bottom which according to your website means my router is a VERSION 1.SO, why is it that my router says it has:
Firmware Version: v1.53.0 Dec 19, 2007
And the latest firmware is
Firmware 11/08/2010 Ver.1.02.11
That looks like an EARLIER firmware version to me judging by the firmware version yet it is dated later. **bleep**. If you want, I can upload a photo of my router's model no. for all to see.My question is, am I safe to 'upgrade' to this 'earlier but dated later' firmware version or not? Why is mine showing as having a later version.
View 4 Replies
View Related
May 27, 2012
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies
View Related
Dec 21, 2011
I just installed a new RV 120W to replace my dlink router.The problem is i cant display the configuration site (192.168.1.1). My internet is working fine and when i go to 192.168.1.1 i can logon (with the password i set using the installation disk) but then i see the top of the config site (blue) but where the config panel should be i see `site cannot be displayed`.
View 4 Replies
View Related
May 31, 2013
Here is a copy of my cisco 881 easy vpn config. What I need to modify so this will work on a cisco 1921.
hostname BTLvpn
boot-start-markerboot system flash:c870-advipservicesk9-mz.124-11.T3.binboot-end-marker
no logging bufferedenable secret 5 XXXXXX
no aaa new-modelclock timezone EASTERN -5
crypto pki trustpoint TP-self-signed-733417695enrollment selfsignedsubject-name cn=IOS-Self-Signed-Certificate-733417695revocation-check nonersakeypair TP-self-signed-733417695
crypto pki certificate chain TP-self-signed-733417695certificate self-signed 01 30820244 308201AD A0030201(code)
View 9 Replies
View Related
Jan 31, 2011
I'm having a problem when configuring this cisco router 1921 with an ip base software. Accordingly with the Cisco software adviser this software allows to configure the l2tp Client Initiated Tunneling. But configuring the router the commands are not recognized:
Router(config)#pseudo wire-class L2TP_PSEUDO
^
% Invalid input detected at '^' marker.
Router(config)#interface Virtual-PPP1.
View 1 Replies
View Related
May 18, 2011
Since Cisco 2511 is out of sale now and Cisco 1900 series are recommended to replace for the purpose of terminal/comm server. How to configure terminal server on HWIC-8A module?
View 3 Replies
View Related
Dec 15, 2011
I have a Cisco 1921 in place with the security IOS so it is also acting as a firewall.
I am wondering if I can enable the GUI so I can configure it remotely.
View 3 Replies
View Related
Dec 15, 2011
I have to open several ports from the WAN to LAN on a 1921:
For example:
Say I need port 41795 both UDP and TCP to go from the WAN to the LAN, can some provide me the context I have to follow?
Currently I have this in place
Another piece of this is that the devices that will need to be accessed remotely are on VLAN10 - will that cause a problem?
is installed at a clients home for a very complex Crestron network that included 5 Cisco POE GB switches, 2 VLANS, with VLAN10 utilizing QOS and is the AV network (VLAN1 is the computer network), 8 1142 WAP's, and this 1921.
=~=~=~=~=~=~=~=~=~=~=~= PuTTY log 2011.12.16 19:52:41 =~=~=~=~=~=~=~=~=~=~=~=show runBuilding configuration...
Current configuration : 3340 bytes!! No configuration change since last restartversion 15.1service timestamps debug datetime msecservice timestamps log datetime msecno service password-encryption!hostname DHOWE_Router!boot-start-markerboot-end-marker!!enable secret 5 $1$JuTn$zn6CnXIm1bJGgPhtRCfB0.enable password ********!no aaa new-model!!no ipv6 cefip source-routeip cef!!ip dhcp excluded-address 192.168.39.0 192.168.39.49ip
[Code] ........
View 3 Replies
View Related
Mar 27, 2012
I have recently configured a cisco 1921 router for internal routing on my network. Here is what i am trying to accomplish:
Main network 10.65.1.0 mask 255.255.255.0- all office devies and computers.
Second network 10.65.2.0 mask 255.255.255.0 - All plant equipment machinery and production lines
i have configure gig 0/0 for my company network and gig 0/1 for my plant network. I can ping the router from both networks but am unable to route traffic betwenn them. what am i missing?
View 8 Replies
View Related
Sep 22, 2011
sample configuration for internet failover . i have 2 ISPs with one coming in thought a serial cable and another through internet and would wish one take over after the other has failed .The router is Cisco 1921 .
View 4 Replies
View Related
Feb 24, 2013
We have frame relay T1 circuit at one of our remote site. Which is connected to our core frame relay router which have DS3 circuit.Now we bought second T1 line at remote site and now I have to configure Bounded T1 with Cisco 1921 router.good config example or document on how to configure frame relay bounded T1 ?
View 1 Replies
View Related
May 20, 2012
i'm having some trouble setting up the correct NAT configuration of a Cisco 1921 router. The NAT is not working as I want - I think my configuration is wrong somewhere. All clients in 172.16.0.0/24 have the correct outgoing address of 1.1.1.3. But the NAT for 10.10.0.4 (and 10.10.0.5, 10.10.0.6) is partially broken: Ping and ssh from the outside world to 1.1.1.4 is "natted" to 10.10.0.4 and works as expected. But from inside (172.16.0.0/24) ssh to 1.1.1.4 should be "natted" to 10.10.0.4, but doesn't work (ping works). ssh from 172.16.0.0/24 to 10.10.0.4 (without doing NAT) works.
network design:
===============
172.16.0.0/16: network for normal use
192.168.64.0/24: network for specific clients and servers
[Code].....
View 1 Replies
View Related
Nov 17, 2011
Whenever some other laptop in my room is using internet with its wifi my wifi stops working. I checked my ping when no laptop was using wifi that its runnig quite smoothly. But as soon as my room mates laptop gets connected to the same network my ping gives me output that "Request timed out".
View 2 Replies
View Related
Jun 19, 2012
This is IOS 15.1(4)M3 on a 1921 router. The LAN is 192.168.42.1/24. (DHCP config is further down.) We have a small range that we want to assign via DHCP to devices; .200 through .220 . At the same time, we have a handful of Macintosh systems to which we want to assign a specific address that is not in that 200-220 range. I don't want to configure the assignment based on the Ethernet MAC addresses because these systems might connect via UTP or wireless; that is to say, they have more than one MAC address. They only ever connect using one interface/MAC address at a time, but it's their choice; in some areas wi-fi is available, and in some areas they have to cable-up.
The Mac OSX network settings has a field for "DHCP Client ID". It would be much easier to tell the users of these systems to put their Mac's name in the Client ID field for both their wired and wireless DHCP configs. (As opposed to having them all lookup, and then give me their Ethernet MAC addresses for both of their interfaces.) I tried this with my Mac's (named "shrike") wi-fi interface, but I don't get the 192.168.42.14 address that I expected. I get an address from the .200 to .220 range.
Here's the DHCP-related config from the router:
router#sh run | s dhcp
ip dhcp excluded-address 192.168.42.1 192.168.42.199
ip dhcp excluded-address 192.168.42.221 192.168.42.254
ip dhcp pool OurOffice
network 192.168.42.0 255.255.255.0
[code]....
Is "client-name" the wrong place to configure the DHCP Client ID?
View 3 Replies
View Related
May 10, 2012
It's exactly the same situation like was described in link below in... 2008 on different forum.PS3 doesn't see the NAS in Wi FI.
1. X3000 Annex A with latest firmware v1.0.01 build 002 Nov 22,2011
2. NAS Zyxel NSA310 with latest firmware 4.50(AFK.0)D0_20120405 running Twonky Media Server (TMS) Twonky 7.0.5 Special connected to X3000 via network cable.
3. Sony Playstation 3 (PS3) with latest firmware 4.11 connected to X3000 via WIFI.
When PS3 is connected via WIFI to X3000, TMS is not visible in PS3. When PS3 is connected via network cable to X3000, TMS is visible and working as hell. No static IP's, whole network based on DHCP. UPnP is ON.Problem mentioned on that different forum was solved by firmware update. Can I expect firmware update also here?
View 1 Replies
View Related
Oct 25, 2011
Would it be possible to change output style of "sh running-config" in SF-300 switches to Cisco IOS-like format (eg.: options related to the specific interface put together, add tabs) in the next release?
View 24 Replies
View Related
Jun 22, 2011
There are some troubles in my 7206 vxr . The process of this problem below.
LOG:
Self decompressing the image : ####################################################################################################################################################################################################################################################################################################################################################################
[Code]...
View 2 Replies
View Related
Jul 13, 2011
command to get running config of Cisco VPN 3000 concentrator.
View 3 Replies
View Related
Feb 3, 2013
I'm running LMS3.2 and RME 4.3.1. I deployed a netconfig job to our network which consisted of approximately 800 devices.The report said that the job completed successfully however some of the devices didn't save thier running config to startup.
Is it possible to add a command or issue another netconfig job just to save the running config, so I can identify if the job fails on some devices? Using the tick box in the netconfig job doesn't seem to alert you if its not successful.
View 2 Replies
View Related
Mar 21, 2012
We were having a discussion in my group about startup vs running configs, and how often some network managers forget to "click save" when they configure a switch. Is there a way to configure Ciscoworks to copy the running config to the startup?
View 2 Replies
View Related
May 24, 2012
I am using ACS5.2 I want user to access the device with all necessary command like show run/ver/int/log… I try to set user privilege using Shell from 1 to 10 but show run doesn't work.
View 15 Replies
View Related
Jan 9, 2012
I am wondering if it's possible to convert a Pix 501 configuration running version 6.3(5) to a new ASA5505 which we just purchased? We have site to site VPN on this device and i am just trying to save some time. I believe Cisco TAC might have a tool to do this but i am not sure.
View 4 Replies
View Related
Aug 7, 2008
We have a bunch of switches that are running fine but the running-config file is missing and we can't save the config to the tftp server. IOS is c3550-ipbasek9-mz.122-37.SE1. I've got lots of these switches running the same code that are just fine.
View 8 Replies
View Related
Oct 5, 2012
We want to puchase new Cisco ISR 1921/K9 . i want to know does it support the following sample IP-SLA commands
ip sla 2icmp-echo 172.16.1.2timeout 500frequency 1ip sla schedule 2 life forever start-time now
track 10 rtr 1 reachability
delay down 1 up 1
!
track 20 rtr 2 reachability
delay down 1 up 1
ip route 0.0.0.0 0.0.0.0 192.168.1.2 track 10ip route 0.0.0.0 0.0.0.0 172.16.1.2 track 20
Im asking above question because we will need to enable ip-sla on the mentioned router. as i read on the cisco webside, it says Cisco-ISR-1921/K9-IP Base support only IP-SLA RESPONDER feature nothing else. If Cisco-921/K9 does not support the above commands , should i go for ordering Cisco-1921-SEC/K9 ?
View 4 Replies
View Related
Jul 28, 2012
My issue is that when trying to run the setup software for my new cisco 4500 router, an error message comes up which states that the new mac operating system 10.8 aka mountain lion is not supported. so now i had no choice but to leave my network unprotected as i cannot run setup. I was just wondering if there was another method by which i can configure the router without running the setup cd.
View 3 Replies
View Related
Apr 2, 2012
My company is beginning to have a lot of sites were we are stacking 3 to 4 C2960S-48 switche.This is making "show running-config" very very long because of the 4 x 48 interfaces.I can’t find a CLI command that show me the running-config of a ranges of interfaces. If I for example would like to see running-config for switch 3 (interfaces 3/0/1-52)The Show Running-config will show all the interfaces (for the two first swtiche = 104 interfaces), which take a time before I reach to switch 3.I miss a CLI command like: show Running-config switch 3, or module 3, or show running-config interface range x/x/x-x ?I’m well aware of the CLI command show running-config interface x/x/x, but this will only show me one interface.
View 3 Replies
View Related
Jun 26, 2011
we have a pix 515E firewall with software version Cisco PIX Security Appliance Software Version 7.0(4) and ASDM version Device Manager Version 5.0(4). we are in a process of upgrading the software. Kindly suggest the software and ASDM version most fit for the device. Also the software should be compatilbe for the current configuation running.
View 3 Replies
View Related
