Linksys Wireless Router :: Cisco 4500 Configuration Without Running Setup CD?
Jul 28, 2012
My issue is that when trying to run the setup software for my new cisco 4500 router, an error message comes up which states that the new mac operating system 10.8 aka mountain lion is not supported. so now i had no choice but to leave my network unprotected as i cannot run setup. I was just wondering if there was another method by which i can configure the router without running the setup cd.
View 3 Replies
ADVERTISEMENT
Oct 26, 2012
I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.
View 9 Replies
View Related
Feb 5, 2013
I can't run the setup cd on my mac running OS 10.8.2.
View 2 Replies
View Related
Jan 11, 2012
Just picked up the E4200 and used Cisco Connect to install. Wanted to know a few things?
-Windows 7, 64 bit
-E4200 router
-AE2500 adapter
1) How can I tell if its running at optimal configuration?
2) Before with my previous router (netgear) I didn't see my router in Device Manager. Now its under Network Infrastructure Devices. It lists the name of my router, under that it lists Microsoft Wireless Router Module??
3) Before with my previous adapter (belkin) I would see my Network Adapter in Device Manager. I see my network adapter listed, under that Realtek PCI (LAN), but now there is another new device? Microsoft Virtual WiFi Miniadapter??
Why are these Microsoft devices showing in Device Manager? Did they not get installed correctly?
View 2 Replies
View Related
Apr 9, 2012
I have Verizon FIOS internet/wireless router and then a WRT310N wireless router connected to it thru Ethernet cable. I want to disable DHCP in the Linksys, but when I try to access the set up page at address 192.168.1.1 the Verizon router set up page shows up. I've tried to connect the router directly to the computer, but it needs the internet connection from the Verizon router. How do I get to the set up of the Linksys at the same time the Verizon is using the same address?
View 5 Replies
View Related
Jun 11, 2013
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies
View Related
May 7, 2013
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies
View Related
Jan 10, 2012
I have the Linksys BEFSX41 wired Firewall router. My ISP is Verizon DSL. The DSL modem is a Westell 6100G. I have the wall phone line connected to my modem. The output of the modem is going to the input of my Linksys router. I have two computers connected to the router outputs. In order for me to see the output or configuration of my Westall modem, I have to go http://192.168.1.1. In order for me to see the configuration of my Linksys router, I have to enter http://10.10.10.1. When I look at the instructions for setting up and configuring my Linksys router, it never mentions the above 10.10.10.1 address, but instead it tells me to enter the 192.168.1.1 address. I have never done this because when I powered both units for the first time, and it worked, I noticed then that my Linksys address was the 10.10.10.1. Why is it then that none of the settings or instructions for the Linksys router never mention to enter the 10.10.10.1 address as oppose to the one the do call out to enter which is the address for the Westell modem? What would happen if both addresses on both devices were the same?
View 2 Replies
View Related
Jun 16, 2012
I needed a faster router because of expanding peripherals. I bought the EA 4500 because I was told that it was the top of the line and the next thing to sliced bread. I needed a VPN to use with this router but when attempting to subscribe I found out that it was not compatible to with VPN and that I needed a firmware,,,DD-WRT, Tomato or PF-Sense compatibility.....Further research indicates that none of those firmware can work with the EA 4500.
View 9 Replies
View Related
Aug 4, 2012
I just bought an EA-4500 and i am having problems with rebooting the device. Every time I change a setting and the router reboots it never starts up again - and the logo LED doesn't flash, it is on constant. I have to cut the power and wait for about 15 minutes, and then it boots up fine - logo flashing and all.
View 5 Replies
View Related
Mar 26, 2013
I have TV set box connected to modem router supplied by ISP provider. To the same router I connected EA 4500 to which I wired connected Network Hard Disc at which I store music, photos and films, which I can not access via TV set box. If I connect Hard Disc direct to the modem router to which set box is connected, access works fine.
Whar shall I do to establish accesability of Network Hard Disc over all network ?
View 1 Replies
View Related
Jun 14, 2012
My EA 4500 wireless speed and range vary drastically by the day under the same conditions.I have tried everything listed on this forum from changing the channels to enabling the Space Time Blk Code mode. It seems to be working fine for a day or so, but eventually the speed and range goes back to being pretty bad!Even with my Ipad or Ipod touch right next to my router, my speed is cut in half compared to the PC connected via Ethernet to the EA 4500 (24 Mbps on PC side and 0.5-10 Mbps on wireless devices.)This router is a really big disappointment for me. It seems very unstable.
View 2 Replies
View Related
Dec 2, 2012
I signed up for Linksys Cloud access.. now going to my browser 'the old way' is disabled.. is there any way to switch back to accessing my EA 4500 using the old way by putting in 192.168.1.1 into the browser?
View 2 Replies
View Related
Feb 4, 2013
Do i need to reset the router after the install all seems good the new firmware installed with no issues.
View 2 Replies
View Related
Nov 17, 2012
I use steed test appnto check the speed of my wireless. I am connected to 5ghz band and using the app most of the time my download speed are between 10-20 Mbps (red line range in app). I noticed that some posts are referring to download speeds of 50mbps. Are my download speed too low? I am in ontario cogeco isp
View 1 Replies
View Related
Feb 18, 2013
I'm not sure why the guest net work is unsecured. I would have thought that would not be an option but it is unsecured. How to secure the guest network [2.4 GHz]? Also when I view the guest list some devices stay displayed whether they are in the vicinity or even turned off. That adds to my paranoia with the guest network being unsecured. I also can't edit the screen names to know who the device belongs to like is available in "my devices", forcing me to keep a MAC address list.
View 2 Replies
View Related
Jun 29, 2012
I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]
View 2 Replies
View Related
Nov 18, 2012
I have 2 story house and trying t extend wireless coverage in the house. I have have 2 routers. One is just wrt54g while the second dual mode EA-4500. Cable modem is located in the basement so i would like to have one of the routers connected to it and use another router as bridge. So which router would be best to use a bridge. If i use ea4500 as a bridge then i would lose dual band features of it.
View 9 Replies
View Related
May 13, 2013
Since we purchased our router in February, we've had intermittent problems with speed, and now it seems to be permanent. If we connect directly to the Comcast modem, everything is fine. If we connect to the router, directly or wirelessly, speeds drop to <3.
View 9 Replies
View Related
May 5, 2013
I have had an EA4500 and EA6500 have the following problem:I have time warner cable internet, Motorola SB6141 modem. The modem connects to an Ooma Telo. The 4500 and then 6500 are connected to the ooma.I have this problem when the routers where placed in front of the ooma as well.
1 time per day, always at the same time, the router stops working. for both wired and wireless connections. i need to unplug the router to work. The modem and ooma continue to work, so i know there is internet getting passed from the modem to the ooma. However, the internet gets disruptted with the routers.
this must be a settings issue with the router. where everyday at the same time, maybe when timewarner changes over or something the router does not pick it up?? i dont know. i have gone through 2 routers and same identical problem.
View 3 Replies
View Related
Apr 25, 2013
I am trying to have a setup where the AP running in autonomous mode also act dhcp server for the wireless clients.The only thing is that the vlan is switched across to the wired network.
So basically i am having 2 vlans, one for mgmt and other for data (for wireless clients) and both vlans are trunked to the switch.
[CODE]...
View 1 Replies
View Related
Oct 26, 2011
how to setup this old switch 4500. It is running CATOS and I want to make sure that when I connect it to the network it doesn't create a loop since it has to be compatible with other vendors, not just Cisco.I don't have anything connected but these are my concerns: It doesn't show my lacp-channel (i believe this is what is used to for Teaming network cards), it doesn't show my trunk ports.
TestSwitch> (enable) show lacp-channel
No ports channelling
TestSwitch> (enable) show trunk ?
detail Show detailed information
<mod> Module number
<mod/port> Module number and Port number(s)
[code]....
View 4 Replies
View Related
Dec 24, 2011
I've gone through a couple modems, only possible reason I can think this is happening, but I don't know for sure if it could be a factor. Anyway, it seems my router is running two... networks? I've reset my router, set up my wireless network, configure the SSID name, password lock it, but there still appears to be a "Linksys" network running with no password. I'm afraid it's being used by someone else, seeing as it's free wifi. I've reset my router a couple times and set up my wifi and this linksys still appears to be running. The reason why I feel it's mine is because one night our net went out and when my brother attempted to log onto the linksys, its net wasn't working either. When our net came back up, the linksys was running with working net once more. It seems like too much coincidence to not be true. I'm really not sure what is causing this and I've never experienced this before.
View 1 Replies
View Related
Apr 4, 2013
I purchased an EA6500 router on March 1 2013 – since then my wireless network has became very unreliable. The network runs fine for a short period of time then it gets extremely slow. I constantly have to reboot the router to see better performance. When I run the built-in router speed check, it shows that I am getting 20 Mbps for downloads which is what I expected to see and then as time goes on, the speed goes as slow as 1 Mbps for downloads. I finally had to go back to my very old Linksys WRT54GS router to have a stable network again. I called Linksys customer support and they want to charge me a fee to diagnose the router that will only be refundable if they find any issues. I find it completely unacceptable to have to spend more money for an item that is only a month old that will probably show no issues when they run their diagnoses since they had me reboot the router while I was on the phone with them. I want to warn others not buy this router especially when the company cannot stand behind their product that is only 34 days old!
View 2 Replies
View Related
Jun 3, 2012
My network consists of a Hughes 7000S modem and Linksys WRT55AG Router. My Windows 7 desktop is hardwired to the router while my wife's Vista computer is connected wirelessly.I recently had to reset the router. When I tried to change the router's password from the familiar "Admin" to a WEP code, the change was never made, although I clicked on "save settings". This has been a persistant problem. I solved this by clicking on "Administration>Management" and entering my own code, however, this has never been necessary before.I am also getting inconsistant "DNS errors". It appears erroneous addresses are being generated.I've downloaded and installed updated firmware.This Linksys router uses WEP security.
View 6 Replies
View Related
Oct 31, 2011
I set up the router in our office and all is working well. BUT, when I have to FTP from my pc to our web server wich is at a typical web hosting company, now we are having time out issues, stalls, an closed sessions.Our server company checked everything and all is clear. I can FTP from outside my office (home) with no issuies at all. So this leads to the E3000 causing the issue. Simply everythign worked on Thursday, we installed on Friday and now we have the issue.
View 3 Replies
View Related
Sep 23, 2011
Apparently the setup cd does not work with Mac OS Lion. Anyone else out there is using this router on a Mac running Lion...if so, how did you set up the router.
View 3 Replies
View Related
Feb 20, 2012
Running an E4200 with Mac OS X Mountain Lion?
View 3 Replies
View Related
Jul 4, 2012
I would like to know on what frequency band running Linksys EA4500 for 5 GHz because in Israel only allowed frequencies from 5150 to 5350 MHz.
View 1 Replies
View Related
Dec 18, 2011
I am unable to connect both of my smart phones to the access point. I am using WPA2 encryption on the AP. I can connect my phones to other AP's using WPA2. I have other devices that connect to the AP except my Android phones. I would like to be able to get some debug logs except the web interface says that the logging fictions are disabled when in bridge mode. Cisco/Linksys tech support: Any troubleshooting tips other than resetting the access point and or reflashing it.
View 4 Replies
View Related
Feb 15, 2012
I have an e4200 set up using a trendnet TEW-684ub. Connection on 2.4Ghz and 5Ghz seems fine, but when the 5Ghz network is under load, such as running speedtest, the network drops for a second. This does not appear to happen on the 2.4Ghz network.
2.4Ghz and 5Ghz networks are set to Auto width and channel using WPA2 and I've tried raising the router up a bit to increase airflow to try to eliminate overheating as a possible issue. I'm also running the latest firmware...1.0.0.3, I believe.
View 5 Replies
View Related
Dec 19, 2011
I have replaced my main router WRT300N running dd-wrt with the a stock E4200 and an old WRT54G aslo running dd-wrt configured for wireless client bridge. Now that I'm learning more about 802.11N, I was wondering what client can I use to achieve 5ghz simultaneously radio transmission since my current setup cannot do this in the 5ghz band. Can the E3000 be ran in wireless client bridge mode, if not what product can provide this? On the other thought am I understanding MIMO?
Old setup: 802.11G 2.4ghz
WRT54G ))) ((( WRT300N ->ISP
Current Setup: 802.11N 2.4ghz MIMO?
WRT300N ))) ((( E4200 ->ISP
Wanted Setup: 802.11N 5ghz MIMO
( E4200 ->ISP)
View 3 Replies
View Related
Oct 9, 2012
Just got an EA6500 - updated to the latest available firmware.I've attached 2 x WD NAS and 1 x WD via USB to the unit.Everytime AFTER I finished running Time Machine on the MacBookPro (writing to one of the WD NAS), I can no longer login to the router neither from the local IP address nor the cisco cloud connect. The error message that I get (loosely phrased) is: can't connect to Router. Please ensure the router is connected to the internet.
View 2 Replies
View Related
