Linksys Wireless Router :: EA 4500 Way To Switch Back To Access?

Dec 2, 2012

I signed up for Linksys Cloud access.. now going to my browser 'the old way' is disabled.. is there any way to switch back to accessing my EA 4500 using the old way by putting in 192.168.1.1 into the browser?

View 2 Replies


ADVERTISEMENT

Linksys Wireless Router :: Get Download Speed Up To 25 Mbps Before Switch Back To E1000

Oct 9, 2012

I just "upgraded" from an E1000 to an E1200 wireless router.  I had good performance with the E1000, and I only upgraded to the E1200 because it was on sale.My only complaint with the E1200 is the slower download speed on my desktop PC that is connected directly to the router.  My normal download speed on the desktop PC was 25 Mbps with the E1000 model.  After I disabled the WMM on the E1200 as others suggested, the download speed on the desktop machine immediately increased from 5 Mbps up to 15 Mbps.   Any other suggestions to get the download speed up to 25 Mbps before I switch back to my E1000? The E1200 router is connected to my Arris TM602G modem.  Both modem and router were reset during the installation process. I setup parental controls for a couple of iPods and configured Open DNS, but other than that, the router is using default settings.  All wireless devices in the house seem to be performing fine with the E1200.

View 8 Replies View Related

Linksys Wireless Router :: EA6500 / How To Switch Back To Old Router

Sep 30, 2012

I need to switch back to my old router currently I am using the EA6500 in the GUI of the latest firmware there is no longer a button "Release IP Address" but it has been replaced with "Release and Renew" button this is causing that the IP address lease form ISP never gets released and I can not switch the routers.

View 9 Replies View Related

Linksys Wireless Router :: EA2700 / 3500 / 4500 Access Restrictions

Jun 29, 2012

I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]

View 2 Replies View Related

Cisco Switching/Routing :: Connect HP 420 Access Point To 4500 Switch

Apr 3, 2012

i am trying to configure my HP 420 access point. I have configure different  SSID on it, This access point is connected to cisco 4500 switch, i have configure trunk on up link to  access point.my problem is the client are not able to get an IP address form the correct vlan if i tagged the SSID to it.

in the following the output of show run int in cisco 4500 switch:
 
interface GigabitEthernet3/13 
description ==== HP ACCess point ====
 switchport trunk allowed vlan 99,130,132 
switchport mode trunk

[code]....

View 1 Replies View Related

Possible To Assign Loop Back Address To Typical Switch Port On 2950 Switch

Jan 16, 2011

is it possible to assign a loopback address to a typical switch port on a 2950 switch? I want to be able to have some devices connected to a switch to test access lists and VLANs.

View 3 Replies View Related

Linksys Wireless Router :: EA 4500 And VPN

Jun 16, 2012

I needed a faster router because of expanding peripherals.  I bought the EA 4500 because I was told that it was the top of the line and the next thing to sliced bread.  I needed a VPN to use with this router but when attempting to subscribe I found out that it was not compatible to with VPN and that I needed a firmware,,,DD-WRT, Tomato or PF-Sense compatibility.....Further research indicates that none of those firmware can work with the EA 4500.

View 9 Replies View Related

Linksys Wireless Router :: BEFW11S4 Connection Goes Out And Itself Come Back

Dec 7, 2011

I have my laptop and my Xbox 360 currently hooked up to this router trough ethernet cables (yes I know it's a very old model, but it's all I have for the time being). I'm having issues with connection that I know is on the router end because the router I had before (that has now gone bad) connected fine, but this one has issues. Literally almost every hour on the dot, the connection goes out and will immediately come back on as soon as I simply unplug the router and plug it back in. Basically, I have to turn the router off and on every hour to continue to stay connected all day, everyday.reason?

View 2 Replies View Related

Linksys Wireless Router :: Turning E2000 Into Access Point / Switch?

Dec 6, 2012

we got a At&T Modem/Router upstairs, and then we got a long ethernet cable running from there to the basement. The problem is that this only allows for one LAN connection at a time (an issue for LAN parties and such). I do have an E2000 Linksys router however and I want to be able to use that as like a switch/access point.I am pretty sure this is possible but I have forgotten all of the steps to do it.The att modem/router is running on 192.168.1.254, and my Linksys which is now directly connected is on 192.168.1.1, so I have a different address in that regards.Do I need to edit my Linksys settings now, or do I have to edit the at&t settings?Also I will be using this for Xbox Live at points so will I need to re-open all those ports up on my Linksys, or at least set the DHCP to the Xbox's static IP to keep my NAT good?

View 2 Replies View Related

Linksys Wireless Router :: E1200 No Internet Port On Back

Sep 19, 2011

I have a question about the function of an E1200 relative to a WRT54G. We currently have the 54G plugged into our LAN, the Ethernet cable plugged into one of the Ethernet ports, not the Internet port, on the back. It is giving wireless clients IP addresses according to our main LAN DHCP, as if they were hard-wired which is correct. Bad thing is, I have no idea what IP address is/was assigned to the 54G itself as it was not logged when done, way before my time. I cannot log into it and take a look at its settings and attempt to mimic what is going on in there on something like an E1200.
 
Therin lies my next questions. What could be occurring on the 54G that is enabling it to dish out like a WAP and does the E1200 support WAP function? If not, which models do that can be added to the 54G? 

View 8 Replies View Related

Linksys Wireless Router :: EA4500 Off / On And Internet Port Came Back On With 1Gb

May 26, 2012

I have a CISCO modem from SHAW set as bridge. I recently bought a CISCO EA4500 which got automatically upgrade to the current Firmware 2.0.37 after connecting it to my ISP. After a few days I noticed my internet speed was slow. When I checked the router I saw it flipped from 1Gb to 100Mb. Called Shaw they could not figure this one out, while waiting I decided to turn everything off / on and internet port came back to 1Gb. 2 days later same thing again, I just turned off both the modem and EA500 router.  A couple of days later again same problem but this time I just turned EA4500 off/on and internet port came back on with 1Gb.Otherwise I will have to turn this one back in to the store for an exchange.

View 9 Replies View Related

Linksys Wireless Router :: WRT54G V1 Disconnect Power From Router For About 15 Seconds / Plug It Back In

Apr 27, 2013

I have a Linksys WRT54G2 v1 router which is having a daily problem of connectiing to the Internet on my home wireless LAN. My temporary solution is to disconnect the power from the router for about 15 seconds and plug it back in .... and all is well.... at least for another day or so.The real problem is that instead of properly connecting to IPv4 address 192.168.1.100 ..... it randomly connects to Autoconfiguration IPv4 address 169.254.29.54 When this problem occurs the SSID list shows both my 192 connection as well as a public network with no Internet connection?
 
I've used this router for several years without a problem until I recently bought a new  Canon wireless MG5320 printer which initially had problems connecting to my LAN. After a telco with tech support the printer works fine but now I am now experiencing the Autoconfig address problem.My LAN consist of the WRT54G router, a Motorola cable modem, a Lenovo laptop running Win7 64bit, a Hp desktop running Win7 64bit  and the Canon wireless printer. (all connected wirelessly)

View 2 Replies View Related

Linksys Wireless Router :: WRT610N Connected To Switch Not Providing Internet Access?

Dec 25, 2012

I just moved in to a new place and have connected my Wireless router (WRT610N) to my switch located in the smart panel in the basement (SE2500). Plugging my ultrabook in to the wall confirms that the signal from the switch in the basement is being sent up, however if I plug my wireless router in to the jack and connect to the wireless router I have no internet access.

View 3 Replies View Related

Linksys Wireless Router :: EA-4500 Freezes When Rebooting

Aug 4, 2012

I just bought an EA-4500 and i am having problems with rebooting the device. Every time I change a setting and the router reboots it never starts up again - and the logo LED doesn't flash, it is on constant. I have to cut the power and wait for about 15 minutes, and then it boots up fine - logo flashing and all.

View 5 Replies View Related

Cisco Switching/Routing :: HWIC-4SHDSL-E Router Back To Back Connection?

Apr 11, 2013

I have two site that has a copper wire ( 2 wire) connection between each router ( No Telco in between ). Now I want to use 1921 router with HWIC-4SHDSL-E card to connect these two site together. Can I use attach configuration to make the connection reference from the diagram ?

View 1 Replies View Related

Cisco Switching/Routing :: Connecting 2650XM - 2620 Router Back To Back WIC - T1?

Nov 25, 2011

I have 2650XM  router and 2620 Router Both routers have built in WIC  T1 CSU/DSU cards
 
2620Router --
 
2620Router#sh int se0/0
Serial0/0 is down, line protocol is down
  Hardware is PQUICC with Fractional T1 CSU/DSU
  Description: DTE  side
  MTU 1500 bytes, BW 1544 Kbit, DLY 20000 usec,
     reliability 255/255, txload 1/255, rxload 1/255
  Encapsulation HDLC, loopback not set

[code]....
 
My question is that cisco website says there are two type of cable connections for this type of config --which are  --T1 CSU/DSU ConfigurationSet one CSU/DSU to clock source internal, and the other CSU/DSU to clock source line. The linecode, framing, data-coding, and timeslots must be set the same on both CSU/DSUs.Four-Wire 56k CSU/DSU Configuration For my network connection which type of config i should use??Secondly i try to connect these ports by normal crossover cable  it did not work.So for this type of connection i know i need T1 cross over cable--  which has RJ 48 connections at both sides.I check cable from ebay which is RJ45 RJ48 cross over  --  will this cable work in my router to router connection.

View 5 Replies View Related

Cisco WAN :: 1921 / Connect Two Router Back To Back Via 2 Pin Copper Wire?

Jan 8, 2013

I would like configure two router (e.g. 1921) back to back via a 2 pin copper wire.  Can I use HWIC-4SHDSL-E card to do it? What is the configuration I can use?

View 7 Replies View Related

Linksys Wireless Router :: EA3500 Upgrade Automatically Turned Back On?

Jul 5, 2012

After I restored my router to the classic firmware last week I unchecked the automatic upgrade box. This morning I found the box checked again. The router still has the firmware version I rolled back to last week. It appears Cisco has the ability to make changes to my router whenever they want.

View 2 Replies View Related

Linksys Wireless Router :: Reverting Back To Old Interface After Using Cisco EA4500

Feb 2, 2013

I have the Cisco Linksys EA4500 router.  It was set up to use the Cisco Cloud Connect.  This interface is horrible.  I can be online and not access my router through ciscocloudconnect.com or 192.168.1.1 while I am on my network.  How is this possible?  I used to have the WRTG54 router and that interface was perfect. How can I switch back to that interface with the EA4500?Cisco Linksys really should have tested their cloud more thoroughly before rolling it out to the public.

View 5 Replies View Related

Linksys Wireless Router :: Get EA6500 Back To Classic Style Firmware?

Nov 18, 2012

Anyway to get the EA6500 back to Classic Style Firmware? I know they offered the roll back on the EA4500.

View 1 Replies View Related

Cisco WAN :: HWIC-4SHDSL-E Router Back To Back Connection

Apr 14, 2013

I have two site that has a copper wire (2 wire) connection between each router ( No Telco in between )Now I want to use 1921 router with HWIC-4SH DSL-E card to connect these two ste together.Can I use attach configuration to make the connection reference from the diagram?

View 2 Replies View Related

Linksys Wireless Router :: EA 4500 - Network Storage Not Visible To TV Set Box?

Mar 26, 2013

I have TV set box connected to modem router supplied by ISP provider. To the same router I connected EA 4500 to which I wired connected Network Hard Disc at which I store music, photos and films, which I can not access via TV set box. If I connect Hard Disc direct to the modem router to which set box is connected, access works fine.
 
Whar shall I do to establish accesability of Network Hard Disc over all network ?

View 1 Replies View Related

Linksys Wireless Router :: EA 4500 Speed And Range Instability?

Jun 14, 2012

My EA 4500 wireless speed and range vary drastically by the day under the same conditions.I have tried everything listed on this forum from changing the channels to enabling the Space Time Blk Code mode. It seems to be working fine for a day or so, but eventually the speed and range goes back to being pretty bad!Even with my Ipad or Ipod touch right next to my router, my speed is cut in half compared to the PC connected via Ethernet to the EA 4500 (24 Mbps on PC side and 0.5-10 Mbps on wireless devices.)This router is a really big disappointment for me. It seems very unstable.

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 Can't Login Into Setup Page

Oct 26, 2012

I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.

View 9 Replies View Related

Linksys Wireless Router :: EA-4500 Just Installed The Cloud Firmware?

Feb 4, 2013

Do i need to reset the router after the install all seems good the new firmware installed with no issues.

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 - Download Speed Too Low Using IPad

Nov 17, 2012

I use steed test appnto check the speed of my wireless.   I am connected to 5ghz band and using the app most of the time my download speed are between 10-20 Mbps (red line range in app).  I noticed that some posts are referring to download speeds of 50mbps.  Are my download speed too low?  I am in ontario cogeco isp

View 1 Replies View Related

Linksys Wireless Router :: Bridge Mode E2500 - Reset It Back To Normal

Nov 18, 2012

I accidently went into bridge mode on my linksys E2500 router. I want to reset it back to normal but i'm not sure how to do it. i tried the little reset button on the router but that didn't change it.

View 4 Replies View Related

Linksys Wireless Router :: WRT54GL Randomly Resets Settings Back To Default?

Mar 18, 2012

I've had my WRT54GL for a couple of months now, and it keeps wiping my saved settings and reverting back to the default. It works fine with all devices for a week or so after the initial set-up, then will only work on the system that is wired.

View 1 Replies View Related

Linksys Wireless Router :: WRT610N - Network Name Reverts Back / Loss Of Password?

May 16, 2012

The network id name for my router has reverted back to linksys a couple of times, also with the loss of password.

View 4 Replies View Related

Linksys Wireless Router :: E2500 Power Led Light On Back Started Blinking

Nov 8, 2012

I have a Linksys E2500 and recently the power led light on the back of the router started blinking.  The router itself seems to be working fine.  I can access the router and the router seems to be assigning the IP addresses fine.  I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking.  Not sure what to do anymore.

View 5 Replies View Related

Linksys Wireless Router :: WRT54GL Manually Power-cycle To Get Internet Back

Aug 15, 2012

We have a Model WRT54GLWireless-G router. At least once a day it loses it's internet connection. All computers that are wired to the switch that is connected to it lose their internet as well as any wireless devices. I have to manually power-cycle the router to get internet back.

View 9 Replies View Related

Linksys Wireless Router :: EA 4500's Guest Network Shows Unsecured

Feb 18, 2013

I'm not sure why the guest net work is unsecured.  I would have thought that would not be an option but it is unsecured.  How to secure the guest network [2.4 GHz]?  Also when I view the guest list some devices stay displayed whether they are in the vicinity or even turned off.  That adds to my paranoia with the guest network being unsecured.   I also can't edit the screen names to know who the device belongs to like is available in "my devices", forcing me to keep a MAC address list. 

View 2 Replies View Related

Linksys Wireless Router :: 2 Story House To Extend Coverage EA-4500

Nov 18, 2012

I have 2 story house and trying t extend wireless coverage in the house.  I have have 2 routers. One is just wrt54g while the second dual mode EA-4500. Cable modem is located in the basement so i would like to have one of the routers connected to it and use another router as bridge. So which router would be best to use a bridge.   If i use ea4500 as a bridge then i would lose dual band features of it.

View 9 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved