Linksys Wireless Router :: EA 4500 And VPN

Jun 16, 2012

I needed a faster router because of expanding peripherals.  I bought the EA 4500 because I was told that it was the top of the line and the next thing to sliced bread.  I needed a VPN to use with this router but when attempting to subscribe I found out that it was not compatible to with VPN and that I needed a firmware,,,DD-WRT, Tomato or PF-Sense compatibility.....Further research indicates that none of those firmware can work with the EA 4500.

View 9 Replies


ADVERTISEMENT

Linksys Wireless Router :: EA-4500 Freezes When Rebooting

Aug 4, 2012

I just bought an EA-4500 and i am having problems with rebooting the device. Every time I change a setting and the router reboots it never starts up again - and the logo LED doesn't flash, it is on constant. I have to cut the power and wait for about 15 minutes, and then it boots up fine - logo flashing and all.

View 5 Replies View Related

Linksys Wireless Router :: EA 4500 - Network Storage Not Visible To TV Set Box?

Mar 26, 2013

I have TV set box connected to modem router supplied by ISP provider. To the same router I connected EA 4500 to which I wired connected Network Hard Disc at which I store music, photos and films, which I can not access via TV set box. If I connect Hard Disc direct to the modem router to which set box is connected, access works fine.
 
Whar shall I do to establish accesability of Network Hard Disc over all network ?

View 1 Replies View Related

Linksys Wireless Router :: EA 4500 Speed And Range Instability?

Jun 14, 2012

My EA 4500 wireless speed and range vary drastically by the day under the same conditions.I have tried everything listed on this forum from changing the channels to enabling the Space Time Blk Code mode. It seems to be working fine for a day or so, but eventually the speed and range goes back to being pretty bad!Even with my Ipad or Ipod touch right next to my router, my speed is cut in half compared to the PC connected via Ethernet to the EA 4500 (24 Mbps on PC side and 0.5-10 Mbps on wireless devices.)This router is a really big disappointment for me. It seems very unstable.

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 Can't Login Into Setup Page

Oct 26, 2012

I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.

View 9 Replies View Related

Linksys Wireless Router :: EA 4500 Way To Switch Back To Access?

Dec 2, 2012

I signed up for Linksys Cloud access.. now going to my browser 'the old way' is disabled.. is there any way to switch back to accessing my EA 4500 using the old way by putting in 192.168.1.1 into the browser?

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 Just Installed The Cloud Firmware?

Feb 4, 2013

Do i need to reset the router after the install all seems good the new firmware installed with no issues.

View 2 Replies View Related

Linksys Wireless Router :: EA-4500 - Download Speed Too Low Using IPad

Nov 17, 2012

I use steed test appnto check the speed of my wireless.   I am connected to 5ghz band and using the app most of the time my download speed are between 10-20 Mbps (red line range in app).  I noticed that some posts are referring to download speeds of 50mbps.  Are my download speed too low?  I am in ontario cogeco isp

View 1 Replies View Related

Linksys Wireless Router :: EA 4500's Guest Network Shows Unsecured

Feb 18, 2013

I'm not sure why the guest net work is unsecured.  I would have thought that would not be an option but it is unsecured.  How to secure the guest network [2.4 GHz]?  Also when I view the guest list some devices stay displayed whether they are in the vicinity or even turned off.  That adds to my paranoia with the guest network being unsecured.   I also can't edit the screen names to know who the device belongs to like is available in "my devices", forcing me to keep a MAC address list. 

View 2 Replies View Related

Linksys Wireless Router :: EA2700 / 3500 / 4500 Access Restrictions

Jun 29, 2012

I can't find info about Access Restrictions in new series of routers.[URL]Do new routers have both Parental Controls + Internet Access Policy? I need this [URL]

View 2 Replies View Related

Linksys Wireless Router :: 2 Story House To Extend Coverage EA-4500

Nov 18, 2012

I have 2 story house and trying t extend wireless coverage in the house.  I have have 2 routers. One is just wrt54g while the second dual mode EA-4500. Cable modem is located in the basement so i would like to have one of the routers connected to it and use another router as bridge. So which router would be best to use a bridge.   If i use ea4500 as a bridge then i would lose dual band features of it.

View 9 Replies View Related

Linksys Wireless Router :: Cisco 4500 Configuration Without Running Setup CD?

Jul 28, 2012

My issue is that when trying to run the setup software for my new cisco 4500 router, an error message comes up which states that the new mac operating system 10.8 aka mountain lion is not supported. so now i had no choice but to leave my network unprotected as i cannot run setup. I was just wondering if there was another method by which i can configure the router without running the setup cd.

View 3 Replies View Related

Linksys Wireless Router :: EA 4500 Slow Upload And Download Speeds?

May 13, 2013

Since we purchased our router in February, we've had intermittent problems with speed, and now it seems to be permanent.  If we connect directly to the Comcast modem, everything is fine.  If we connect to the router, directly or wirelessly, speeds drop to <3. 

View 9 Replies View Related

Linksys Wireless Router :: EA Series 4500 And 6500 Routers Disconnecting

May 5, 2013

I have had an EA4500 and EA6500 have the following problem:I have time warner cable internet, Motorola SB6141 modem.  The modem connects to an Ooma Telo.  The 4500 and then 6500 are connected to the ooma.I have this problem when the routers where placed in front of the ooma as well.
 
1 time per day, always at the same time, the router stops working.  for both wired and wireless connections.  i need to unplug the router to work.  The modem and ooma continue to work, so i know there is internet getting passed from the modem to the ooma. However, the internet gets disruptted with the routers.
 
this must be a settings issue with the router.  where everyday at the same time, maybe when timewarner changes over or something the router does not pick it up?? i dont know. i have gone through 2 routers and same identical problem.

View 3 Replies View Related

D-Link DGL-4500 / Using Second Wi-Fi Router As Wireless Bridge?

Oct 16, 2012

I purchased a D-Link DGL-4500 to replace my aging WRT54G around a year ago, only to find it nowhere near as reliable. It's been collecting dust since.I'm wondering if there is a way to use it as a wireless bridge so I can connect it to my home network and then use it's ethernet ports to provide network access to several devices.

View 2 Replies View Related

D-Link DGL-4500 - Long Range Wireless Router

Apr 21, 2012

I currently have a D-Link DGL-4500.

I am looking for a more powerful wireless router that has a larger range. I want to have the ability to use the laptop at the house next door, so I need a range of like 150 ft, going through multiple walls (both concrete and wood) and still have enough for general Internet access.

My first question is if it's even possible and if so, what is a good router/system to use.

I would still need the ability to connect Ethernet to the router (at least 4 ports) and the wireless, obviously.

A major benefit as well would be the ability to install something like pfSense or DD-WRT onto for further management.

View 8 Replies View Related

HP Officejet 4500 - Does Wireless Printer Tether To Dsl Router With Cable?

Sep 11, 2011

i just bought an HP Officejet 4500 wireless all-in-one printer. i imagined this would mean that my laptop can print to the printer without a USB cable, but also that the printer itself would not have to "cable" to anything, but rather be wireless and located anywhere in the house. was i wrong? does this printer HAVE to connect physically with the router box?

View 1 Replies View Related

Keep Getting Disconnected From Dlink DGL-4500 Router?

Oct 5, 2011

Our router is a Dlink DGL-4500. Over the last 15 minutes I've been disconnected and reconnected about 5 or 6 times. This happens every so often. But even without it I get disconnected several times per day.I need to be able to stay online and for some certain programs to run, if they get disconnected I will have to reconnect manually and I can't do this if I am not near my computer.I think the problem is specific to my laptop. Most of the time I stay online ok, except for the lapses I've mentioned. I asked someone else in our house if they have been getting disconnected and they say they haven't. Here's an IPconfig and in the next quote box, I did an IPconfig/all>C:esults.txt, which I've posted the content of[CODE]

View 14 Replies View Related

Cisco WAN :: Configure QoS In Router 1841 For Port (500 / 4500)

May 29, 2013

how can I configure QoS in the router CISCO1841 for  the port IPSEC(UDP 500 ,UDP 4500) and the port tcp 4433

View 5 Replies View Related

Cisco Switching/Routing :: 4500 - Run Dhcp Off The Router

Jan 2, 2013

I have setup a 4500 series core/router.. the customer decided to run dhcp off the router for whatever reason... I have 20 different scopes handing out to their vlans. Does each vlan interface need an helper address?
 
vlan 1 on router is 10.85.0.1
i used the ip dhcp-server command pointed to 10.85.0.1
 and then for ex. 
int vlan 20
ip add 10.85.20.1 255.255.248.0   
ip helper-address 10.85.0.1 
 
i am now getting a loopback error on the router, and i believe this is the cause...

View 2 Replies View Related

DGL 4500 DLink Router - Accessing Computers / Printers On Other Side Of Bridge?

Oct 13, 2011

I have a DGL-4500 D-Link router as a base. And a DAP 1522 Ethernet Bridge I use to connect 3 devices and another router I am looking to host a media Server for the house(on the bridge).

View 5 Replies View Related

Cisco VPN :: Preventing Remote Router From Using Random Port Numbers / Only Allowed To Use 4500

Nov 1, 2011

I have a remote site that is using port 4500 for within the isakmp phase of creating a IPSEC tunnel, but for some reason it is also using random port numbers constantly (in bold): [code] These are all blocked by the firewall when trying to communicate with our central router in the trusted network. The central router does not display the same symptoms, it only uses port 4500.Is there a way of preventing the remote router from using random port numbers and only allowed to use 4500??

View 9 Replies View Related

Cisco Wireless :: 4500 - Single WLAN To Multiple VLANs

Feb 27, 2013

I read from this forum some discussion about the WLC VLAN Select feature. [URL]. I see that you can use this feature to have multiple VLANS (interfaces) to map to the same WLAN (SSID).
 
What I try to learn is under what scenarios would people need to have mutliple vlan mapped to single SSID?
 
In my environment, I have 50+ AP int he campus on 20+ Cisco 4500 switches.  I have single WLAN and it is mapped to one subnet.  All wireless users would be on that subnets, whereas wired users are on 20+ subnets of their own.

View 6 Replies View Related

D-Link DGL-4500 Configuring Rock Solid Small Network Of Around 20 Wireless Devices

Sep 27, 2011

I have a single WRT54G v5 that has treated me very well over the years. I have too many devices right now and I'd like to throughput of N, but have failed to find one that is measurably faster or as stable than my current equipment. Most recently I tried a D-Link DGL-4500 and regardless of hours of configuration, research and support I was left with slower-than-expected speeds and dropped connectivity about once a day.

I want to be able to stream media to all 3 BoxeeBox's simultaneously while browsing the internet on a few of my devices and I don't want to have to reboot my router daily or even weekly.

So far I have come to a preliminary conclusion that a solid setup for me would be a ZyXEL ZyWALL USG20 and 2 to 3 Ubiquiti UniFi AP's. While the USG20 does intimidate me, I have several solid network admins that have told me they'll set up the network for me and walk me through it.

View 19 Replies View Related

Cisco WAN :: IOS XE Upgrade On 4500-x

Feb 20, 2013

Have a new 4500-x (Comes with IPBase enabled), but I see only universal image is available for download  (Which I understand has "all" features)...assume it is safe to use the latest universal image on 4500-x and the IPBase license will be automatically applied?
 
I also see there is a new rom upgrade available - Is this the correct procedure to follow:  [URL]
 
Should I be doing the rom upgrade first?

View 1 Replies View Related

Cisco :: 4500 Won't Change To SSO Redundancy

Sep 6, 2011

I have a 4510R+E switch that won't change to the SSO redundancy mode. After entering the 'mode SSO' command, the switch reboots the peer supervisor (as it says it will), but after it comes back up it remains in RPR mode. I've tried rebooting the peer supervisor manually, rebooting the entire chassis, manually power cycling the entire chassis, and reseating the sups, but the switch remains in RPR mode. The issue started when I swapped the switch's supervisor with the supervisor of another 4500. The same issue was observed on the other 4500 as well, but after several reboots, I got it to change to SSO mode. Prior to the swap, both switches were running in SSO mode just fine.Since we're running IOS version 15.0 with the 'spare sup' license, I suspect the issue arose because of licensing complications (with relation to the chassis serial number and the like) when I swapped the sups....although this doesn't explain why the other switch changed to SSO after some troubleshooting.

View 1 Replies View Related

Cisco :: 4500 Can't See Status Of Interface

Oct 27, 2012

I do terminal monitor on my 4500 switch.I can't see the status of the interface ( when it become up or down)What is the problem? I need to add a command?

View 3 Replies View Related

Cisco WAN :: 4500 - PDLM RTP Audio

Dec 12, 2011

Im trying to locate the PDLM for the RTP audio for the 4500 series switch,
 
 System image file is "boot flash:cat4500-entservices-mz.150-2.SG.bin"
  
Cisco WS-C4507R+E (MPC8245) processor (revision 7) with 524288K bytes of memory.
MPC8245 CPU at 333Mhz, Supervisor IV
Last reset from Power Up
8 Virtual Ethernet interfaces
48 Fast Ethernet interfaces
100 Gigabit Ethernet interfaces
403K bytes of non-volatile configuration memory.
  
It seems to be an easy task for routers:
 
[URL]
 
But not for these 4500's
 
[URL]

View 1 Replies View Related

Cisco WAN :: How To Setup 4500 CatOs

Oct 26, 2011

how to setup this old switch 4500. It is running CATOS and I want to make sure that when I connect it to the network it doesn't create a loop since it has to be compatible with other vendors, not just Cisco.I don't have anything connected but these are my concerns:  It doesn't show my lacp-channel (i believe this is what is used to for Teaming network cards), it doesn't show my trunk ports.
  
TestSwitch> (enable) show lacp-channel
No ports channelling
 TestSwitch> (enable) show trunk ?
  detail                     Show detailed information
  <mod>                      Module number
  <mod/port>                 Module number and Port number(s)

[code]....

View 4 Replies View Related

DGL-4500 - Unable To Connect To Internet?

Jul 23, 2011

Got this router based on the above sticky. Logged into the router and did the Internet connection wizard. Won't connect to the internet. Did it manually and entered in the correct dns ip's. Still nothing.

Got this to finally update to N. Upgrading from a wrt54g which works perfectly with the same cables but not with the dgl4500.

Ps: hardware version is A1 and the firmware is stock 1.02.

View 7 Replies View Related

Cisco WAN :: 4500 Switches With Supervisor 6E-L

Jun 8, 2011

we got 2 Cisco 4005 Switches with IOS 12.x. t.Now we have two new Cisco 4500 Switches with Supervisor 6E-L.But i dont really understand the new syntax / configuration method of ios 15.

View 2 Replies View Related

Cisco :: 4500 Adding Additional Module?

Jul 28, 2012

Im wanting to add an additional module in to my Cisco 4500. Is as simple as plug and play or is there some commands that I need to add or anything I should be aware of.

View 2 Replies View Related

Cisco :: Disabling CPP On 4500 Series Switch?

Dec 1, 2011

We inherited a lot of the equipment from another team of network administrators and every now and then, we run into a switch with some old code or configuration that was left behind and missed by us. Today, I discovered that CPP was enabled on 3 of our access-layer switches in one of the buildings we support.

View 3 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved